hit counter script
Toro Power Clear 518 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Snow Blower
  5. Power Clear 518
  6. Operator's manual

Toro Power Clear 518 Operator's Manual

Hide thumbs Also See for Power Clear 518:
Table of Contents

Advertisement

Quick Links

Power Clear® 518 Snowthrower
Model No. 38472—Serial No. 402082000 and Up
Model No. 38473—Serial No. 402082000 and Up

Introduction

This machine is intended to be used by residential
homeowners. It is designed primarily for removing
snow from paved surfaces, such as driveways and
sidewalks, and other surfaces for traffic on residential
or commercial properties. It is not designed for
removing materials other than snow, nor is it designed
for clearing gravel surfaces.
Note:
The machine may leave rubber marks on
new brushed or light-colored concrete. Test on an
inconspicuous location before use.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.
Important:
With your smartphone or tablet, scan
the QR code on the serial number decal to access
warranty, parts, and other product information.
1. Model and serial number location
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Figure 1
Figure 1
Register at www.Toro.com.
Model No.
Serial No.
This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(Figure
2), which signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
g216757
Original Instructions (EN)
Form No. 3415-616 Rev B
Operator's Manual
Figure 2
Safety-alert symbol
All Rights Reserved *3415-616* B
Printed in Mexico
g000502

Advertisement

Table of Contents
loading

Related Manuals for Toro Power Clear 518

Summary of Contents for Toro Power Clear 518

  • Page 1: Introduction

    Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product.

  • Page 2: Table Of Contents

    Clearing a Clogged Discharge Chute ....10 a dealer convenient to you, access our website Self-Propelling the Snowthrower ...... 10 at www.Toro.com or contact our Toro Customer Operating Tips ..........10 Care Department at the number(s) listed in your After Operation .............11 Emission Control Warranty Statement.

  • Page 3: Safety

    Safety • Do not operate the machine without all guards and other safety protective devices in place and working on the machine. General Safety • Keep clear of any discharge opening. Keep bystanders a safe distance away from the This machine complies with ANSI B71.3 specifications. machine.

  • Page 4: Setup

    Installing the Recoil-Start Setup Handle Installing the Handle g218390 Filling the Engine with Oil g218388 Installing the Discharge Chute g218389 g216207 Adjusting the Control Cable Refer to Checking and Adjusting the Control Cable (page 12).

  • Page 5: Product Overview

    Product Overview Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Before Operation Safety • For electric-start models only: Use extension cords and receptacles as specified in the manual. Thoroughly inspect the electrical cord before plugging it into a power source.

  • Page 6: Filling The Fuel Tank

    Filling the Fuel Tank Checking the Engine-Oil Level • For best results, use only clean, fresh (less than 30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). Service Interval: Before each use or daily •...

  • Page 7: During Operation

    Starting the Engine During Operation Push the ignition key fully inward to the O position (Figure 12). During Operation Safety • Shut off the engine before unclogging the machine and always use a stick or the snow-cleanout tool (if provided). •...
  • Page 8 WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it. Replace or repair the damaged cord immediately. Contact an Authorized Service Dealer for assistance.

  • Page 9: Engaging The Rotor Blades

    Engaging the Rotor Blades Shutting Off the Engine To engage the rotor blades, hold the control bar To shut off the engine, pull the ignition key outward against the handle (Figure 17). until it clicks into the O position (Figure 19) or move the choke lever fully to the right (Figure...

  • Page 10: Adjusting The Discharge Chute And Chute Deflector

    Adjusting the Discharge Self-Propelling the Chute and Chute Deflector Snowthrower To adjust the discharge chute, move the chute handle Lift the machine handle until the wheels are just off as shown in Figure the ground and the scraper and rotor blades touch the ground.

  • Page 11: After Operation

    After Operation After Operation Safety • Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

  • Page 12: Maintenance

    • Do not change the governor settings on the engine. • Purchase only genuine Toro replacement parts g011568 Figure 23 and accessories. 1. Control bar 2. 2 to 3 mm (1/16 to 1/8...

  • Page 13: Inspecting The Rotor Blades

    Adjusting the Control Cable Slide up the spring cover and unhook the spring from the adjuster link (Figure 24). g011544 Figure 25 1. The wear-indicator hole is 2. The wear-indicator hole is intact; you do not need to exposed; replace the rotor replace the rotor blades.

  • Page 14: Servicing The Spark Plug

    Servicing the Spark Plug Service Interval: Yearly—Service the spark plug and replace it if necessary. Use a Toro spark plug (Part No. 119-1961). Shut off the engine and wait for all moving parts to stop. Disconnect the wire from the spark plug...

  • Page 15: Replacing The Drive Belt

    Replacing the Drive Belt If drive belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt. Remove the 4 bolts that hold the drive-belt cover (Figure 29) in place. g011642 Figure 30 1. Belt guide 2. Engine pulley Note: Do not distort or damage the belt guide.

  • Page 16: Storage

    Storage Storing the Machine WARNING Fuel fumes are highly flammable, explosive, and dangerous if inhaled. If you store the product in an area with an open flame, the fuel fumes may ignite and cause an explosion. • Do not store the machine in a house (living area), basement, or any other area where ignition sources may be present, such g013829...

This manual is also suitable for:

3847338472

Table of Contents

Save PDF