Table of Contents
Advertisement
Quick Links
S e n d f e e d b a c k t o n e x u s 4 K - d o c f e e d b a c k @ c i s c o . c o m
Cisco Nexus 4001I and 4005I Switch Module for
IBM BladeCenter Getting Started Guide
This document includes the following sections:
•
•
•
•
•
•
•
•
Overview
This guide provides instructions on how to install, configure, and manage your Cisco Nexus 4001I and
4005I Switch Module for IBM BladeCenter-referred to as the switch module-in the IBM BladeCenter
enclosure, and how to set up and configure your switch module.
For additional installation and configuration information about the switch module, see the switch module
documentation on Cisco.com.
For blade enclosure compatibility, system requirements, important notes, limitations, open and resolved
caveats, and last-minute documentation updates about the switch module, see the release notes, also on
Cisco.com. When you use the online publications, refer to the documents that match the Cisco NX-OS
software version that is running on the switch module.
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Overview, page 1
Safety Warnings, page 2
Verifying your Shipping Contents, page 2
Connecting Devices, page 3
Configuring the Switch, page 4
Managing the Switch, page 9
Related Documentation, page 10
Advertisement
Table of Contents
Related Manuals for Cisco Nexus 4005I
Summary of Contents for Cisco Nexus 4005I
-
Page 1: Table Of Contents
• Overview This guide provides instructions on how to install, configure, and manage your Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter—referred to as the switch module—in the IBM BladeCenter enclosure, and how to set up and configure your switch module. -
Page 2: Safety Warnings
Use the guidelines in this section to ensure your own personal safety and to help protect your device from potential damage. For a complete list of all warnings and compliance information, see the Regulatory Compliance and Safety Information for the Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter, which ships with the switch module. -
Page 3: Connecting Devices
EEPROM that is encoded with security information. This encoding provides a way for Cisco to identify and validate that the module meets the requirements for the switch module. If the validation fails, the software will not bring up the port. -
Page 4: Configuring The Switch
For more information about enabling or disabling autonegotiation and auto-MDIX, see the Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter NX-OS Command Reference and the Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter NX-OS Configuration Guide on Cisco.com. - Page 5 The applicable bay number appears in the pane, followed by other related I/O-module information, including the IP address. The I/O-module information is divided into two areas: Current IP Configuration and New Static IP Configuration (see Figure Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter Getting Started Guide OL-19952-02...
-
Page 6: Initial Setup
Telnet to the mgmt1 IP address and log in using the following (default) user ID and password: Login ID is USERID. • • Password is PASSW0RD (the 0 in PASSW0RD is a zero). You can now configure the switch module. Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter Getting Started Guide OL-19952-02... - Page 7 Mgmt0 IPv4 netmask: 255.255.255.0 Configure the IPv4 default gateway (recommended) by entering yes (or y). Enter the gateway IP address. Step 9 Configure the default gateway? (yes/no) [y]:y Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter Getting Started Guide OL-19952-02...
- Page 8 Note The switch module has two out-of-band management interfaces. The AMM configuration is mgmt1. The mgmt0 interface must be placed on a different subnet than mgmt1. Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter Getting Started Guide OL-19952-02...
-
Page 9: Managing The Switch
CLI by connecting your management station directly to the switch module console port or by using Telnet from a remote management station. For more information about using the CLI, see the Cisco Nexus 4001I and 4005I Switch Module for IBM BladeCenter NX-OS Command Reference. -
Page 10: Related Documentation
ROSA, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.