Configuration Guidelines - Cisco Catalyst 2950 Software Configuration Manual
Hide thumbs
Also See for Catalyst 2950:
- Configuration manual (710 pages) ,
- Command reference manual (686 pages) ,
- Software configuration manual (544 pages)
Table of Contents
Advertisement
Chapter 10
Configuring Interface Characteristics
These sections describe how to configure the interface speed and duplex mode:
•
•
•
For information about configuring the CPE 10/100 port speed and duplex mode, see the
Catalyst 2950 LRE Switches" section on page 12-1
page
Configuration Guidelines
When configuring an interface speed and duplex mode, note these guidelines:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
78-11380-12
Configuration Guidelines, page 10-11
Setting the Interface Speed and Duplex Parameters on a Non-LRE Switch Port, page 10-12
Setting the Interface Speed and Duplex Parameters on an LRE Switch Port, page 10-13
12-11.
Ethernet ports set to 1000 Mbps should always be set to full duplex.
A Gigabit Ethernet port that does not match the settings of an attached device can lose connectivity
and does not generate statistics.
If both ends of the line support autonegotiation, we highly recommend the default setting of auto.
When connecting an interface to a 100BASE-T device that does not autonegotiate, set the speed to
a nonautonegotiation value (for example, nonegotiate), and set the duplex mode to full or half to
match the device. The speed value and duplex mode must be explicitly set.
When connecting an interface to a Gigabit Ethernet device that does not autonegotiate, disable
autonegotiation on the switch, and set the duplex and flow control parameters to be compatible with
the remote device.
100BASE-FX ports operate only at 100 Mbps and in full-duplex mode.
1000BASE-SX ports operate only at 1000 Mbps and in full-duplex mode.
1000BASE-T GBICs operate only at 1000Mbps and in full-duplex mode.
You can configure the 10/100/1000 ports on the Catalyst 2950T-24 and Catalyst 2950T-48-SI
switches to autonegotiate the duplex mode by using the duplex auto interface configuration
command, or you can manually set the duplex mode to full by using the duplex full command.
The 10/100/1000 ports on the Catalyst 2950T-24 switches operate only in full-duplex mode. The
ports do not support the half keyword in the duplex command.
The 10/100/1000 ports on the Catalyst 2950T-48-SI switches support the half keyword when the
interface speed is 10 or 100 Mbps.
10/100/1000 ports on the Catalyst 2950 LRE or the Catalyst 2955T-12 switch can operate at 10 or
100 Mbps in either half- or full-duplex mode. The ports can operate at 1000 Mbps only in
full-duplex mode.
Fiber-optic SFP-module ports on the Catalyst 2950 LRE switch operate only at 1000 Mbps in
full-duplex mode.
GigaStack-to-GigaStack cascade connections operate in half-duplex mode, and GigaStack-
to-GigaStack point-to-point connections operate in full-duplex mode.
When Spanning Tree Protocol (STP) is enabled and a port is reconfigured, the switch can take up to
30 seconds to check for loops. The port LED is amber while STP reconfigures.
On the 10/100/1000 ports on an LRE switch, use the speed and duplex interface commands. You
cannot configure the speed and duplex settings on the fiber-optic SFP-module ports.
and the
"CPE Ethernet Link Guidelines" section on
Catalyst 2950 and Catalyst 2955 Switch Software Configuration Guide
Configuring Ethernet Interfaces
"Ports on the
10-11
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
