Selecting X2/Twingig Convertor Mode - Cisco Catalyst 4500 Series Software Configuration Manual
Cisco ios xe release 3.9.xe and cisco ios release 15.2(5)ex
Hide thumbs
Also See for Catalyst 4500 Series:
- Administration manual (1814 pages) ,
- Configuration manual (1610 pages) ,
- Command reference manual (1230 pages)
Table of Contents
Advertisement
Selecting X2/TwinGig Convertor Mode
The default configuration mode is X2. If you plan to deploy 10-Gigabit Ethernet interfaces, you do not need to configure
anything. However, if you want to deploy Gigabit interfaces (that is, use TwinGig Convertors), you must configure the
associated port-group:
To determine how the X2 holes on a module are grouped, enter the show hw-module module m port-group p command.
Note
Place a 10-Gigabit Ethernet port that accepts CVR-X2-SFP into 1-Gigabit mode instead of 10-Gigabit Ethernet mode.
If you configure a 10-Gigabit Ethernet port as 1-Gigabit port, an output similar to the following appears:
Switch# show hw-module module 5 port-group
Module Port-group Active
-------------------------------------------------------------
5
1
Gi5/3-6
If the port is set to the default, 10-Gigabit Ethernet mode, an output similar to the following appears:
Switch# show hw-module module 6 port-group
Module Port-group Active
-------------------------------------------------------------
6
1
Te6/1-2
Switch# show int status mod 1
Port
Name
Te1/1
Te1/2
Te1/3
Te1/4
Te1/5
Te1/6
Gi1/7
Gi1/8
Gi1/9
Gi1/10
Gi1/11
Gi1/12
Gi1/13
Gi1/14
Gi1/15
Gi1/16
Gi1/17
Gi1/18
Switch#
•
To configure the modes of operation for each X2 port group in which you want to deploy Gigabit, enter the hw-module
module m port-group p select gigabitethernet command. This configuration is preserved across power cycles and
reloads.
To deploy Gigabit Ethernet interfaces using the TwinGig Convertor, perform this task:
Command
Step 1
Switch# configure terminal
Step 2
Switch(config)# hw-module module m port-group p
select [gigabitethernet | tengigabitethernet]
Deploying 10-Gigabit Ethernet or Gigabit Ethernet Ports
Status
notconnect
connected
notconnect
notconnect
notconnect
notconnect
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
inactive
Catalyst 4500 Series Switch, Cisco IOS Software Configuration Guide - Cisco IOS XE 3.9.xE and IOS
9
Inactive
Te5/1-2
Inactive
Gi6/3-6
Vlan
Duplex
Speed Type
1
full
10G 10GBase-LR
1
full
10G 10GBase-LR
1
full
10G No X2
1
full
10G No X2
1
full
10G No X2
1
full
10G No X2
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
1
full
1000 No Gbic
Purpose
Establishes global configuration mode.
Selects the mode of operation for each X2 port-group.
Default is 10-Gigabit Ethernet (x2).
Chapter 9
Configuring Interfaces
Advertisement
Chapters
Table of Contents
Troubleshooting
