Sony STR-V200 Operating Instructions Manual
Hide thumbs
Also See for STR-V200:
- Operating instructions manual (24 pages) ,
- Limited warranty (1 page) ,
- Service manual (32 pages)
Related Manuals for Sony STR-V200
Summary of Contents for Sony STR-V200
- Page 1 3-862-695-12(1) FM Stereo FM-AM Receiver Operating Instructions STR-V200 © 1998 by Sony Corporation...
- Page 2 (servicing) Before connecting other components, be below. Refer to them whenever you call instructions in the literature sure to turn off and unplug the receiver. upon your Sony dealer regarding this accompanying the appliance. product. On cleaning INFORMATION Clean the cabinet, panel and controls Model No.
-
Page 3: Table Of Contents
ABLE OF CONTENTS About This Manual Getting Started The instructions in this manual are for Unpacking 4 model STR-V200. Hookup Overview 4 Conventions Antenna Hookups 5 • The instructions in this manual Audio Component Hookups 6 describe the controls on the receiver. -
Page 4: Getting Started
Getting Started Getting Started Unpacking Hookup Overview Check that you received the following items with the The receiver allows you to connect and control the receiver: following audio/video components. Follow the • FM wire antenna (1) hookup procedures for the components that you want •... -
Page 5: Antenna Hookups
Getting Started Getting Started Important Antenna Hookups If you connect an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Overview This section describes how to connect AM and FM Note antennas to the receiver. -
Page 6: Audio Component Hookups
Getting Started Audio Component Hookups Speaker System Hookups Overview Overview This section describes how to connect your audio This section describes how to connect your speakers to components to the receiver. If you want to use the the receiver. Although front (left and right) speakers receiver as an amplifier, complete these connections. -
Page 7: Video Component Hookups
Getting Started Getting Started Hookups Video Component Hookups Front speakers Front speaker Front speaker Receiver Overview SPEAKERS REAR CENTER FRONT This section describes how to connect video components to the receiver. – – – – IMPEDANCE USE 8-16Ω TV/DBS VIDEO Note ANTENNA SPEAKERS... -
Page 8: Ac Hookups
Getting Started AC Hookups Before using the receiver for the first time Connect the AC power cord from this receiver and Do the procedure below to set the receiver’s stored from your audio/video components to a wall outlet. parameters (preset stations, etc.) to their factory If you connect a component to AC OUTLET on the settings. -
Page 9: Receiver Operations
Getting Started Receiver Operations Receiver Operations Do this Selecting a Component Mute the sound Z Press MUTING on the remote. Press again to restore the sound. To listen to or watch a connected component, first Reinforce the bass Z Press BASS BOOST on the remote select the function on the receiver or with the remote. - Page 10 If you use a Sony TV When you press TV to watch a TV program, the TV The remote lets you operate the receiver and the Sony turns on and switches to the TV input. The TV also components that are connected to it.
-
Page 11: Receiving Broadcasts
Press 1/u to turn on the receiver. ENTER DVD player Press TUNER. Sony VCRs are operated with a VTR 1, 2 or 3 setting The last received station is tuned in. that corresponds to Beta, 8mm, and VHS, respectively. Press FM or AM to select FM or AM stations. -
Page 12: Presetting Radio Stations
Receiver Operations If you cannot tune in a station and the entered Presetting Radio Stations numbers are flashing Make sure you’ve entered the right frequency. If not, press DIRECT and reenter the frequency you want. You’ll most likely want to preset the receiver with the If the entered numbers still flash, the frequency is not radio stations you listen to often so that you don’t have used in your area. -
Page 13: Recording
Getting Started Receiver Operations Tuning preset stations (preset tuning) Recording You can tune directly to a preset station by entering its preset number. If you don’t know which stations are This receiver makes it easy to record to and from the preset on which numbers, you can tune by scanning components connected to the receiver. -
Page 14: Selecting A Surround Mode
Receiver Operations Recording on a video tape Selecting a Surround Mode You can record the audio portion of TV programs or DBS programs using the receiver. You can also add You can take advantage of surround sound simply by audio from a variety of audio sources when editing a selecting one of the three pre-programmed surround video tape. -
Page 15: Getting The Most Out Of Dolby Pro Logic Surround Sound
Getting Started Receiver Operations You can find Dolby Surround-encoded software by Getting the Most out of Dolby looking at the packaging However, some videos and laser discs may use Dolby Pro Logic Surround Sound Surround sound even if it’s not indicated on the package. - Page 16 Receiver Operations You can adjust all the speakers at one time Press SET UP repeatedly to select the center mode Press MASTER VOL +/– on the remote or turn you want by referring to the following table. MASTER VOLUME on the main unit. If you have Select So that...
-
Page 17: Additional Information
/ Set your TV to the appropriate input mode (press TV/ / The protective device on the receiver has been VIDEO on the remote for Sony TVs). activated because of a short circuit (“PROTECT” / Place your TV away from the audio components. -
Page 18: Specifications
Additional Information Outputs TAPE/MD REC OUT: General Specifications Voltage: 150 mV, System Tuner section: Impedance: 10 kilohms PLL quartz-locked digital VIDEO AUDIO OUT: synthesizer system Voltage: 150 mV, Preamplifier section: AUDIO POWER SPECIFICATIONS Impedance: 10 kilohms Low-noise NF type MIX AUDIO OUT: equalizer Voltage: 2 V Power amplifier section:... -
Page 19: Glossary
Getting Started Additional Information • PHANTOM mode Dolby Pro Logic Surround Glossary Select PHANTOM mode if you have Decoding system of Dolby Surround front and rear speakers and no center sound standardized in TV programs speaker. The sound of the center and movies. - Page 20 Additional Information Surround sound • In a system without a center speaker (PHANTOM mode) Sound that consists of three elements: The test tone is output from the front direct sound, early reflected sound (early reflections) and reverberative and the rear speakers alternately. sound (reverberation).
-
Page 21: Rear Panel Descriptions
Getting Started Additional Information Rear Panel Descriptions 2 3 4 !¡ ANTENNA SPEAKERS AC OUTLET AC 120V 60Hz REAR CENTER FRONT SWITCHED 120W/1A MAX TAPE/MD TV/DBS VIDEO AUDIO AUDIO AUDIO AUDIO – – – – 300Ω IMPEDANCE USE 8-16Ω 75Ω 1 ANTENNA 2 CD 3 TAPE/MD... -
Page 22: Remote Button Descriptions
–/– – — Not applicable Tape deck Sets tape deck to the record standby mode Only for Sony TVs with the picture-in-picture function r + ( Tape deck/MD Starts recording when pressed with ( (or 9 on deck/VCR Note tape deck) The PHONO button on the remote does not operate. -
Page 23: Index
Getting Started Index Advanced Remote Operations Adjusting Scanning radio stations. See delay time 16 Automatic tuning effect level 15 Selecting a component speaker volume 16 on the main unit 9 Automatic tuning 12 using the remote 10 Selecting center mode 15 surround mode 14 Battery 4 Speakers... -
Page 24: Quick Reference Guide
VIDEO – TUNING SURROUND ON/OFF – TUNING (To continue scanning.) SURROUND Press repeatedly to select MODE Receiving Preset Stations C.STUDIO Example: Receiving station number A7 Turn on the VCR. TUNER Start playing. SHIFT Select A. Sony Corporation Printed in China...