Page 4
SANYO Factory Code Z6BF Service Reference NO. 715 DP26671 SERVICE MANUAL 26" HDTV LCD / DVD Combo ORIGINAL MFR'S VERSION A Design and specifications are subject to change without notice.
IMPOTANT WARNING CAUTION: DVD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER THIS PLAYER USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE PLAYER. (Printed on the Rear Panel) WHEN THIS PLAYER IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF...
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. PERFORM A SAFETY CHECK AFTER SERVICING As for the places which need special attentions, they are indicated with the labels or seals on the Confirm that the screws, parts and wiring which cabinet, chassis and parts.
WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD MT PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector.
DISC REMOVAL METHOD AT NO POWER SUPPLY 1. Remove the Stand A'ssy, Back Cabi Ass'y. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) 2. Slide the Rack Base toward the arrow direction by hand to release the lock. (Refer to Fig. 1) 3.
HOW TO DSM-5 DISC IRREGULAR EJECT 1. You must be take off power cord first and waiting until Disc stop then proceeding further. 2. Insert the long wood bar or steel bar (diameter Caution: • Please take out Disc with the above method. If you use other method, it maybe NG. •...
ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.) Caution: • Pb free solder has a higher melting point than standard solder; Typically the melting point is 86 F~104 F(30...
HOTEL MODE FUNCTION To set the Hotel mode, please follow the steps below. 1. In power on mode, set the VOLUME to minimum. 2. Press and hold the VOLUME DOWN button on the front panel. 3. Simultaneously press and hold the MENU button on the remote control for more than 2 seconds.
TABLE OF CONTENTS IMPOTANT WARNING ..........................A1-1 SERVICING NOTICES ON CHECKING ....................A1-2 HOW TO ORDER PARTS …………………………………………………………………………………………. A1-2 IMPORTANT ............................A1-2 WHEN REPLACING DVD DECK ......................A1-3 PREPARATION OF SERVICING ......................A1-3 A1-4 DISC REMOVAL METHOD AT NO POWER SUPPLY ................A1-5 HOW TO DSM-5 DISC IRREGULAR EJECT ...................
GENERAL SPECIFICATIONS LCD Size / Visual Size 26.01 inch / 660.5mmV System LCD Type Color TFT LCD Number of Pixels 1366(H) x 768(V) Double Scan View Range Left/Right 80/80 degree Up/Down 80/70 degree < Bright Dot Zero Bright Dot Ratio Color System NTSC Speaker...
Page 14
Game Timer Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-SC Glow in Dark Remocon Control Remocon Format SANYO Format Custom Code 38-C7 h Power Source Voltage(D.C) UM size x pcs UM-3 x 2 pcs Total Keys...
Page 15
GENERAL SPECIFICATIONS Auto Shut Off G-11 Features Auto Search Power On Memory Hotel Mode Comb Filter Game Position Auto Setup Language TV Location E-POP Demo Signal Type Automatic Search Auto Setup(in Setup Menu) Picture Setting(TV) Picture Preference Brightness , Contrast , Color Tint Sharpness Color Temperature...
Page 16
GENERAL SPECIFICATIONS Yes (Some USB devices may not be usable.) Time Shift Playback File DivX MPEG-4 Visual H.264/MPEG-4 AVC Real Media MPEG-4 AAC FLAC JPEG iPod iPhone iPad Software Update Digital Out Dolby Digital MPEG PC Monitor Input VGA (640x480) Yes (60,72,75Hz) VGA (720x400) Yes (70Hz)
Page 17
GENERAL SPECIFICATIONS Wall Mount Size W x H(mm) Yes (100 x 100) Screw Size M4 x 10 Stand Tilt Swievel Features Progressive Video Out (DVD/CD) Digital Out (Dolby Digital) (MPEG) (PCM) (DTS) No (Possible to output) Decode(Down Mix) (Dolby Digital) (DTS) (SACD) (DVD-Audio)
Page 18
GENERAL SPECIFICATIONS Owner's Manual Language English / Spanish G-12 Accessories w/Guarantee Card Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet Quick Set-up Sheet...
Page 19
Container Stuffing (40' container) Sets/40' container w/Pallet w/Wrapping Cabinet Front ABS 94HB G-17 Material Rear PS 94V0 NON-DECABROM Stand PS 94HB Jack Panel Non-Halogen Demand Eyelet Demand G-18 Environment Environmental standard requirement Green procurement of SANYO Pb-free Phase3(Phase3A) Measures for Whisker Rohs A3-7...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: DVD MT PCB/LOADER UNIT (Refer to Fig. 1-3) AND P.C. BOARDS 1. Remove the 4 screws (1). 2. Remove the Shield Deck in the direction of arrow (A). CAUTION 3. Remove the screw (1). Be careful not to remove the LVDS cable forcibly, because 4.
Page 21
DISASSEMBLY INSTRUCTIONS 1-4: MAIN PCB ASS'Y (Refer to Fig. 1-4) 1. Remove the 6 screws (1) 2. Remove the Plate Jack in the direction of arrow (A). 3. Remove the Shield Jack in the direction of arrow (B). 4. Disconnect the following connectors: (CP2804, CP3002, CP3003, CP4201 and CP6201).
DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DVD DECK PARTS Check Lock NOTE 1. Disassemble only the DVD DECK PARTS parts listed here. Minute adjustments are needed if the Check Lock disassembly is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y. 2-1: TRAVERSE ASS'Y/LOADER SUB ASS'Y (Refer to Fig.
Page 23
DISASSEMBLY INSTRUCTIONS NOTE TOP SIDE 4 PIN FFC Check Hook 1. In case of the Gear Motor installation, check if the value Traverse Ass'y of the Fig. 2-2-B is correct. 2. When installing the wire of the PCB630 install it correctly Check Hook as Fig.
Page 24
DISASSEMBLY INSTRUCTIONS NOTE Roller Sub Ass'y 1. In case of the Shutter Roller Ass'y installation, Safety surface for check if the value of the Fig. 2-3-B is correct. pressing of the insert. 2. In case of the Roller Cone installation, install correctly as (OK) (NG) Fig.
Page 25
DISASSEMBLY INSTRUCTIONS Gear Middle 3 Loading Motor PCB Ass'y Rack Base Gear Middle 4 • Install wire from (1) to (2) in order. Pulley Motor Gear Pulley Clamper Magnet Loading Motor BROWN(2) Gear Main RED(1) Gear Middle 2 Fig. 2-4-D Gear Middle 1 Belt Loading •...
Page 26
DISASSEMBLY INSTRUCTIONS • Install the Rack Base as the arrow (1) • Install Boss of Rack Base as the arrow (2) After Ass'y Check Rib Frame Sub Ass'y Check Boss Check Lock Check Boss Rack Base Fig. 2-4-F 2-5: FFC WIRE HANDLING 1.
DISASSEMBLY INSTRUCTIONS 3. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after FLAT PACKAGE IC desoldering completely, pickup the corner of the IC using tweezers and remove the IC by moving with the IC REMOVAL desoldering machine.
Page 28
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- 1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 3-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition.
SERVICING FIXTURES AND TOOLS Ref. No. Part No. Parts Name Parts Name JG176 Up-Date Disc JG176 APJG176161 Up-Date Disc Up-Date of the Firmware RE-WRITE FOR DVD FIRMWARE 1. Turn on the power, and set the DVD mode. 2. Confirm that the "No Disc" will be appeared on the screen. 3.
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0".
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE NO. FUNCTION NO. FUNCTION Read and perform these adjustments when repairing the 03 R DRIVE (N) 35 TINT circuits or replacing electrical parts or PCB assemblies. 04 R CUTOFF (N) 36 SHARP H1 MAX 05 G DRIVE (N) 37 SHARP H1 MIN CAUTION 06 G CUTOFF (N)
Page 33
ELECTRICAL ADJUSTMENTS 2-2: BRIGHTNESS CENT 2-3: CONTRAST MAX 1. Place the set in Aging Test for more than 15 minutes. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the color bar pattern. (RF Input) 2.
Page 34
ELECTRICAL ADJUSTMENTS 2-4: CONTRAST CENTER 2-5: CONTRAST 40 1. Place the set in Aging Test for more than 15 minutes. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the color bar pattern. (RF Input) 2.
Page 35
ELECTRICAL ADJUSTMENTS 2-6: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (TV/AV/COMPONENT/HDMI/PC/DVD/DTV) COMPONENT HDMI DVI--->HDMI FUNCTION CVBS 480i 480p 720p 1080i 480i 480p 720p 1080i 1080p 640×480 720×400...
BLOCK DIAGRAM <Main PCB> DVD_Power DISC_IN MT1389K UART (MediaTek) DSM-5 DDR2 SDRAM w/o USB Time Shift Model : 512Mbit EJ-WRITER Serial Flash (UPDATE) 32Mbit w/ USB Time Shift Model :1Gbit DVD_SPDI DVD AUDIO AA22 <Remocon PCB> DVD_Power DISC IN UART Remocon 受信部...
WAVEFORMS FLASH SOUND 20ns 10us 200mV 100mV 200mV SCALER VIDEO/AUDIO 20us 500mV 100mV 200mV MPEG/MICON/DSP 10us 0.5V 100mV 200mV JACK 20us 20ns 500mV 100mV 200mV 10us 200mV 100mV 200mV 200ns 10us 0.2us 200mV 100mV 200mV NOTE : The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 64
WAVEFORMS VIDEO/AUDIO IN/OUT 10us 200mV 10us 200mV 50ms NOTE : The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) SCREW ASS'Y, POLYBAG INSTRUCTION (RED CAUTION), INFORMATION SHEET (RETURN), INSTRUCTION BOOK (E/S), INFORMATION SHEET (PICTURE QUALITY) FILM BAG (791WHAA435) TRANSMITTER CD501 PACKAGE TOP PACKAGE TOP LAMIFILM BAG FILM BAG (791WHAA433) PACKAGE BOTTOM PACKAGE BOTTOM GIFT BOX LABEL CARTON LABEL GIFT BOX I1-3...
DVD DECK EXPLODED VIEW CD2301 PCB630 PCB610 (LOADING MOTOR PCB ASS'Y) Do not replace the parts. Because, minute adjustments are needed if CD2302 this condition is disassembled M2601 further more. SW002 If the repair is needed, replace the SW001 DVD MECHA ASS'Y. M2603 CLASS PART NO.
MECHANICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION 7A708A587A FRONT CABI ASS'Y 101A 708WPA0061 CABINET FRONT 101B 713WPA0464 GLASS LED 101C 800WQ00181 FELT SHEET 7A702B506A BACK CABI ASS'Y 102A 702WPA1572 CABINET BACK 102B 735WPA0991 BUTTON FRAME 102C 761WSA0790 ANGLE BACK 761WSA0791 ANGLE BACK 102D 761WSA0896 ANGLE BACK 2...
Page 73
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION CAPACITORS CAPACITORS C2308 CS0UCH4L1J CC PF 50V CH C2870 CS0UB0N15K CC 0.1 UF 10V B C2309 CS0UCH412J CC 100 PF 50V CH C2871 CS0UB0N15K CC 0.1 UF 10V B C2310 CS0UB0413K CC 0.001 UF 50V B...
Page 74
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION CAPACITORS CAPACITORS C3086 CS0RB0N17K CC UF 10V B C4038 CS0UB0N15K CC 0.1 UF 10V B C3090 CS0UB0N15K CC 0.1 UF 10V B C4043 CS0UB0314K CC 0.01 UF 25V B C3093 CS0RB0N17K CC UF 10V B...
Page 75
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION CAPACITORS CAPACITORS C5846 CS0UB0215K CC 0.1 UF 16V B C8533 CS0RB0N17K CC UF 10V B C5848 CS0UB04Q3K CC 0.0047UF 50V B C8534 CS0UCH412J CC 100 PF 50V CH C5849 CS0UB04Q3K CC 0.0047UF 50V B...