Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Acer Aspire 4810 Series
Summary of Contents for Acer Aspire 4810 Series
- Page 1 Aspire 4810 Series Disassembly Instruction...
-
Page 2: Machine Disassembly And Replacement
Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. Disassembly Requirements To disassemble the computer, you need the following tools: Wrist grounding strap and conductive mat for preventing electrostatic discharge •... -
Page 3: Table Of Contents
General Information Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: Turn off the power to the system and all peripherals. Unplug the AC adapter and all power and signal cables from the system. Place the system on a flat, stable surface. -
Page 4: B M2 X L3
External Module Disassembly Process Item Screw Color M2 x L3 Silver M3 x L3 Black M2.5 x L11 Black... -
Page 5: Removing The Battery Pack
Removing the Battery Pack Turn base unit over. Slide the battery lock/unlock latch to the unlock position. Slide and hold the battery release latch to the release position. Then slide out the battery from the battery bay. Note: Battery has been highlighted with the red rectangle as above image shows. Please detach the battery and follow the local regulations for disposal. -
Page 6: Removing The Lower Cover
Removing the Lower Cover See “Removing the Battery Pack” on page 5. Remove the two screws (F) and five captive screws securing the lower cover. Step Size (Quantity) Color Torque M2.5 x L11 (2) Black 3.0 kgf-cm Use a plastic screw driver to carefully pry open the lower cover. Remove the lower cover from the lower case. -
Page 7: Removing The Optical Drive Module
Removing the Optical Drive Module See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover” on page 6. Use a screw driver and carefully push out and slide out the optical drive module out of the bay. Remove the one screw (B) securing the locker bracket and remove the locker bracket from the optical disk drive module. -
Page 8: Removing The Hard Disk Drive Module
Push out the latches on both sides of the DIMM socket to release the DIMM and remove it from the socket. Do the same to the other socket if there is any DIMM present. Removing the Hard Disk Drive Module See “Removing the Battery Pack”... -
Page 9: Removing The Ssd Module
Remove the two screws (D) securing the hard disk to the bracket and remove the hard disk from the bracket. Step Size (Quantity) Color Torque M3 x L3 (2) Black 3.0 kgf-cm Removing the SSD Module See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover”... - Page 10 Disconnect the RTC battery cable from the system board and lift to remove it. NOTE: Be careful when removing the RTC battery. It is glued to the system board. Note: Battery has been highlighted with the red rectangle as above image shows. Please detach the battery and follow the local regulations for disposal.
-
Page 11: E M2.5 X L6
Main Unit Disassembly Process Item Screw Color M2 x L4 Black M2.5 x L6 Black M2.5 x L5 Black M2 x L6 Black... -
Page 12: Removing The Keyboard
Removing the Keyboard See “Removing the Battery Pack” on page 5. Release the keyboard from the latches securing it. Carefully pry loose the keyboard. Place the keyboard below the LCD screen to gain access to the keyboard cable. -
Page 13: Removing The Wlan Board Module
Disconnect the keyboard cable from the main board to remove the keyboard. Removing the WLAN Board Module See “Removing the Battery Pack” on page 5. See “Removing the Keyboard” on page 12. Disconnect the antenna cables from the WLAN board. NOTE: There are 2 antenna cables connected to the WLAN board. -
Page 14: Black
Remove the one screw (A) on the WLAN board to release the WLAN board. Step Size (Quantity) Color Torque M2 x L4 (1) Black 1.6 kgf-cm Detach the WLAN board from the WLAN socket. NOTE: When attaching the antenna back to the WLAN board, make sure the cable are arranged properly. Separating the Upper Case from the Lower Case See “Removing the Battery Pack”... -
Page 15: Black
11. Remove the twelve screws (I, E, H) from the bottom panel. Step Size (Quantity) Color Torque M2.5 x L6 (2) Black 3.0 kgf-cm M2 x L4 (2) Black 3.0 kgf-cm 5~12 M2.5 x L5 (8) Black 3.0 kgf-cm 12. Disconnect the touchpad cable from the TPAD1 connector on the main board. 13. -
Page 16: Removing The Power Button Board
14. Disconnect the power button cable from the BTB2 connector on the system board. 15. Disconnect the speaker cable from the SPK1 connector on the system board. 16. Gently separate the upper case from the lower case. Removing the Power Button Board See “Removing the Battery Pack”... -
Page 17: Removing The Touchpad Module
See “Removing the Optical Drive Module” on page 7. See “Removing the DIMM” on page 7. See “Removing the Hard Disk Drive Module” on page 8. See “Removing the SSD Module” on page 9. See “Removing the RTC Battery” on page 9. See “Removing the Keyboard”... -
Page 18: Removing The Speaker Module
12. Disconnect the touchpad cable from the touchpad board; then carefully pry loose and remove the touch pad board WARNING:The touchpad board is glued to the upper case, only remove the touchpad board if it is defective. Note: Circuit board > 10cm has been highlighted with the red rectangle as shown in the figure above. -
Page 19: Removing The Led Board
12. Remove the two screws (A) securing the left and right speaker modules, peel off the stickers securing the speaker cables, and remove them from the upper case. Step Size (Quantity) Color Torque M2 x L4 (2) Black 1.6 kgf-cm Removing the LED Board See “Removing the Battery Pack”... -
Page 20: Removing The Lcd Module
13. Carefully pry loose and remove the LED board from the upper case. WARNING:The LED board is glued to the upper case, only remove the LED board if it is defective. Removing the LCD Module See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover”... - Page 21 13. Disconnect the LCD cable. 14. Pell off the LCD cable from the fan. 15. Remove the two screws (E) from the left and right hinge of the LCD module. Step Size (Quantity) Color Torque M2.5 x L6 (2) Black 3.0 kgf-cm...
-
Page 22: Removing The System Board
16. Carefully remove the LCD module from the base unit. NOTE: When connecting the cables back to the unit, please note that the cables should be routed well. Removing the System Board See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover”... - Page 23 14. Disconnect the top daughter board cable from the system board. 15. Disconnect the bottom system board cable from the daughter board. 16. Remove the one screw (A) securing the system board and the mini board.. Step Size (Quantity) Color Torque M2 x L4 (1) Black...
-
Page 24: Removing The Thermal Module
17. Carefully remove the main board. Removing the Thermal Module See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover” on page 6. See “Removing the Lower Cover” on page 6. See “Removing the Optical Drive Module” on page 7. See “Removing the DIMM”... -
Page 25: Removing The Mini Board Module
14. Turn over the system board and loosen the four captive screws securing the thermal module. 15. Carefully remove the heatsink module from the system. Removing the Mini Board Module See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover” on page 6. See “Removing the Lower Cover”... -
Page 26: Removing The Daughter Board Module
13. Remove the one screw (A) securing the mini board to the system board. Step Size (Quantity) Color Torque M2 x L4 (1) Black 1.6 kgf-cm 14. Detach the system board from the mini board. Note: Circuit boards > 10cm has been highlighted with the red rectangle as shown in the figure above. -
Page 27: Removing The Card Reader Board
12. See “Removing the System Board” on page 22. 13. Release the daughter board from the latch. 14. Carefully lift the daughter board and remove it from the lower case. Note: Circuit board > 10cm has been highlighted with the red rectangle as shown in the figure above. -
Page 28: Removing The Bluetooth Module
13. Remove the one screw (A) securing the card reader board to the lower case. Step Size (Quantity) Color Torque M2 x L4 (1) Black 1.6 kgf-cm 14. Remove the card reader board from the lower case. Note: Circuit board > 10cm has been highlighted with the red rectangle as shown in the figure above. -
Page 29: Removing The Touchpad Lock Board
12. See “Removing the Card Reader Board” on page 27. 13. Disconnect the Bluetooth module cable from the bottom of the card reader board. 14. Carefully pry loose and remove the Bluetooth module from the card reader board. WARNING:The Bluetooth module is glued to the card reader board, only remove the Bluetooth module if it is defective. - Page 30 12. Carefully pry loose and remove the touchpad lock board from the lower case. WARNING:The touchpad lock board is glued to the lower case, only remove the touchpad lock board if it is defective.
-
Page 31: Lcd Module Disassembly Process
LCD Module Disassembly Process Item Screw Color M2.5 X L3.5 Silver M2 x L2.5 Silver M2 x L3 Black... -
Page 32: Removing The Lcd Bezel
Removing the LCD Bezel See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover” on page 6. See “Removing the Lower Cover” on page 6. See “Removing the Optical Drive Module” on page 7. See “Removing the DIMM” on page 7. See “Removing the Hard Disk Drive Module”... -
Page 33: Removing The Lcd Panel
15. Carefully pry open the LCD bezel and and remove the bezel from the LCD panel. Removing the LCD Panel See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover” on page 6. See “Removing the Lower Cover” on page 6. See “Removing the Optical Drive Module”... - Page 34 15. Remove the four screws (G) securing the LCD panel to the back cover. Step Size (Quantity) Color Torque M2 x L2.5 (4) Silver 1.6 kgf-cm 16. Carefully lift up the LCD panel and turn it over to gain access to the LCD cable. 17.
-
Page 35: Removing The Lcd Panel Hinges
18. Detach the LCD cable from the LCD panel. 19. Remove the LCD panel from the back cover. Removing the LCD Panel Hinges See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover” on page 6. See “Removing the Lower Cover” on page 6. See “Removing the Optical Drive Module”... -
Page 36: Removing The Webcam
15. Remove the four screws (J) securing the left and right hinges, and remove the hinges Step Size (Quantity) Color Torque M2.5 x L2.5 (4) Black 1.6 kgf-cm Removing the Webcam See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover” on page 6. See “Removing the Lower Cover”... -
Page 37: Removing The Microphone
14. Disconnect the cable from the webcam. 15. Carefully pry loose the webcam. CAUTION: Only remove the webcam if it is defective as it is glued to the back cover. Removing the Microphone See “Removing the Battery Pack” on page 5. See “Removing the Lower Cover”... - Page 38 14. Disconnect the cable from the microphone, then remove the microphone.