DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S MICROCOMPUTER’S TERMINAL DESCRIPTION ● SYSTEM μ-COM R5F3650KDFB (X34-700: IC301) Truth Value Pin No. Pin Name Application Processing Operation Description Table REMO Remote controller input (INFRARED, WIRED) Pulse width detection Not used Output L fi xed BYTE CNVSS Software writing-in mode control...
Page 7
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Value Pin No. Pin Name Application Processing Operation Description Table NC (9B1) Not used (9B1) Output L fi xed H: Can overwrite ROM correction ROMCOR_DET ROM correction writing-in request (Switch SDA6 and SCL6 to slave operation)
Page 8
Not used Output L fi xed AVSS Not used Output L fi xed VREF AVCC 98,99 NC Not used Output L fi xed Not used (Kenwood brand model) Output L fi xed (Kenwood brand model) STE_REMO Steering remote controller input (DOP)
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE 1. Overview ● Target models MODEL NAME DEVELOPMENT CODE TYPE DPX-308U C-1023WK DPX-U5120/DPX-U5120S C-1023WM DPX-U500 C-1023WJ DPX-404U C-1023WE DPX-MP3120 C-1024WM DPX-U304 C-1024WE ● Exterior specifi cation Exteriors and key assign and names in all the target models, are as shown below.
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE ● Description explanation Display specifi cation of this document is described by the following forms. ÷ ÷ ÷ ÷ Description of display Description Disc Eject count display (Max. 65535 times). Disc Eject While Disc Eject count is displayed, press and hold for 2 count display ■...
Page 12
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE • In the test mode, even if the prescribed period of time elapses, the backup memory items are not written in save area (Data Flash/ E2PROM). • In the test mode, the opening display shall be omitted for the easy recognition of the mode transfer.
Page 13
3 . 0 version display LOW: SYS04-x.xx DOP information display * Displays DOP type in 4 digits. * Displays “– – – –” for Kenwood brand model. DOP information (Pressing [PRESET-1] key briefl y again, MID model display (forward transfers to the mechanism model name and mecha-...
Page 14
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE Description of display Description Displays 00~50 in “XX”. Displays it for less than 1 hour Disc operation in the unit of 10 minutes. time display Displays 00001~10922 in “XXXXX”. MAX 10922 (hour) Disc operation Press and hold this key for 2 seconds in the Disc op- ■...
Page 15
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE Description of display Description In CD information display mode, perform the display CD information switch of displayed information (forward rotation). ROTARY UP display switching (Ex.) CD eject error information display (forward rotation) Eject error 1 → Eject error 2 → Eject error 3 →...
Page 16
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE Description of display Description Press and hold for 1 second to enter the TUNER set- ting adjustment mode (AUTO). When the source is FM, ■ DISP Mode transfer frequency is switched to 98.3MHz (M/E/K), 83.0kHz (J) at the start of the adjustment mode.
Page 17
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE w TUNER setting adjustment mode (MANUAL) Description of display Description [Level Offset adjustment (Manual)] S-xx: Current S-meter value (Hex) Normal display L-xx: Level offset value (Hex) – – * When the level offset value is not adjusted (0xFF or 0x00), “–...
Page 18
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE ● Test mode specifi cation with CD source Operation for CD-DA media (KTD-02A) Description of display Description Normal display P-TIME display (default) [ ] key operation enables the truck jumps in the fol- lowing sequence. No.9 → No.15 → No.10 → No.11 → No.12 → No.13 →...
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE Procedure in compressed media Description of display Description File type display (MP3) File type display The fi le format is displayed just before the fi le play- (WMA) back. File type display (AAC) ● Audio adjustment The operation specifi...
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE 4. Security code forced deletion function ● How to transfer to the mode (E destination) When a code is requested, press and hold [SEEK UP] key for 3 seconds while pressing [BAND] key to be transferred to the mode, ([–][–][–][–]) will be cleared.
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE Description of display Description DC error detection status display While pressing When DC error is detected (capacitor leaks, misconnections or any and holding [3] other errors are detected): “ERR” key and [6] key, When DC error is not detected (no capacitor leaks, misconnections reset-start.
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE 7. ROM correction writing-in function ● How to transfer to the mode While pressing and holding [PRESET-6] + [SEARCH], reset to transfer to the ROM correction writing-in mode. The opening display shall be omitted for the easy recognition of the mode transfer.
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S TEST MODE 8. DOP setting function ● How to transfer to the mode While pressing and holding [ATT] + [PRESET-6], reset to transfer to the DOP setting mode. The opening display shall be omitted for the easy recognition of the mode transfer.
Page 28
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S PC BOARD (COMPONENT SIDE VIEW) SWITCH UNIT X16-7120-2x (J76-0741-02) X16-7120-2x Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 29
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S PC BOARD (FOIL SIDE VIEW) SWITCH UNIT X16-7120-2x (J76-0741-02) X16-7120-2x Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 30
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S PC BOARD (COMPONENT SIDE VIEW) DPX304, DPX-MP3120 X32 B/2 12EJE CD PLAYER UNIT X32-6240-00 A/2 (J76-0546-02) 3.3V IOP- AGND RFRP BU1.5 D1.5V DM1.5V DGND S GND S 7.5V D3.3V MOTOR ZDET SLED IN/EJECT SLED OUT/LOAD X32-6240-00 Ref. No.
Page 31
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S PC BOARD (FOIL SIDE VIEW) DPX304, DPX-MP3120 X32 B/2 CD PLAYER UNIT X32-6240-00 A/2 (J76-0546-02) X32-6240-00 Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 32
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S PC BOARD (COMPONENT SIDE VIEW) DPX308U/DPX404U, DPX-U5120/U5120S X32 B/2 12EJE ORG LOS GRE GND BLU R105 CD PLAYER UNIT R102 X32-6260-01 A/2 (J76-0572-02) AGND CD RST IOP+ BUCK A3.3V R119 R177 CP11 R101 R121 12EJE SW R171 R118...
Page 33
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S PC BOARD (FOIL SIDE VIEW) DPX308U/DPX404U, DPX-U5120/U5120S X32 B/2 CD PLAYER UNIT X32-6260-01 A/2 (J76-0572-02) R127 R120 R128 CP15 R166 CP12 C102 R167 R68 R69 R132 R131 X32-6260-01 Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 34
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S (X34-700x-xx) L422 A8V-2 4.7uH PRE OUT BU5V FRONT D421 IC300 ∗ ∗ J401 J401 VOUT REAR / SUB F412 PATTERN FUSE3 TP305 R306 IC420 R301 ∗ ∗ REAR / SUB FRONT E-VOL C401 C402 C405 C406 R302 1000P...
Page 36
: UDZW6.8(B) di vid u al in stru ments or/ Q120 : RT1N441M-T111 D120 : UDZW4.7(B) DGND Q400-403 : RT1N430M-T111 D203,401,421 : DAP202U and units. DPX304/308U/404U, DPX-MP3120/U5120/U5120S (1/2) (X34-700x-xx) SIGNAL LINE UNIT DESTI- R36,160-162, R163,164, IC301 MODEL NAME C525 C710...
Page 38
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S ED1 (SEGMENT) ED1 (COMMON) DPX304/308U/404U, DPX-MP3120/U5120/U5120S (2/2) DTC114YUA DTC144EUA CAUTION : For continued safety, re place safe ty critical com po nents only with manufacturer’s rec om- 2SA1576A mend ed parts (refer to parts list). Indicates safety critical com po nents. To reduce the...
Page 39
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S DPX304, DPX-MP3120 CD PLAYER UNIT (X32-6240-00) (A/2) MECHA. (X92- ) SLED OUT /LOAD TP28 4ch BTL DRIVER 1.7V TP345 7.5V D1.5V POWVCC1 R58 100 TP26 LOADING & POWGND1 SLED IN SLED /EJECT TP346 MOTOR SLIN VO1- R59 200K...
DPX304/DPX308U/DPX404U DPX-MP3120/U5120/U5120S EXPLODED VIEW (PANEL) : N80-2005-48 : N82-2006-48 (X16-) Depends on the models. Refer to the parts list. Parts with the exploded numbers larger than 700 are not supplied.
SOCKET FOR PIN ASSY 3F ✽ K24-5095-03 PUSH KNOB (BACK) M3E3 QNZ1057-001 USB CONNECTOR QNZ1057-001 USB CONNECTOR K1M1M2 E2: DPX404U E3: DPX304 (Europe) K1: DPX308U (North America) Indicates safety critical com po nents. M1: DPX-U5120 M2: DPX-U5120S M3: DPX-MP3120 (Other Areas)
Page 48
CD PLAYER UNIT (X32-6240-00/6260-01) CK73GB1H103K CHIP C 0.010UF K K1M1M2 CK73FB0J106K CHIP C 10UF M3E3 CK73GB1A105K CHIP C 1.0UF E2: DPX404U E3: DPX304 (Europe) K1: DPX308U (North America) Indicates safety critical com po nents. M1: DPX-U5120 M2: DPX-U5120S M3: DPX-MP3120 (Other Areas)
Page 49
CHIP C 1000PF RK73GB2A225J CHIP R 2.2M J 1/10W M3E3 C73 ,74 CK73GB1H102K CHIP C 1000PF K1M1M2 E2: DPX404U E3: DPX304 (Europe) K1: DPX308U (North America) Indicates safety critical com po nents. M1: DPX-U5120 M2: DPX-U5120S M3: DPX-MP3120 (Other Areas)
Page 50
J 1/10W E2 RK73GB2A000J CHIP R J 1/10W K1M1M2 R105 RK73GB2A104J CHIP R 100K J 1/10W K1M1M2 E2: DPX404U E3: DPX304 (Europe) K1: DPX308U (North America) Indicates safety critical com po nents. M1: DPX-U5120 M2: DPX-U5120S M3: DPX-MP3120 (Other Areas)
Frequency response (±1 dB) ......10 Hz – 20 kHz Total harmonic distortion (1 kHz) ......0.008 % KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be Signal to Noise ratio (1 kHz) ........110 dB Dynamic range .............
Page 57
Dynamic range ............. 93 dB MP3 decode ..Compliant with MPEG-1/2 Audio Layer-3 WMA decode .....Compliant with Windows Media Audio KENWOOD follows a policy of continuous advancements AAC decode .......... AAC-LC “.m4a” fi les in development. For this reason specifications may be changed without notice.
Frequency response (±1 dB) ......10 Hz – 20 kHz Total harmonic distortion (1 kHz) ......0.008 % KENWOOD follows a policy of continuous advancements Signal to Noise ratio (1 kHz) ........105 dB in development. For this reason specifications may be Dynamic range .............