hit counter script
Toro 73471 Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 73471
  6. Setup instructions
Toro 73471 Setup Instructions

Toro 73471 Setup Instructions

Hide thumbs Also See for 73471:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Loose Parts
Note:
Use the chart below to identify parts for assembly.
DESCRIPTION
Seat Assembly
Shoulder Bolt – 5/16"
Locknut – 5/16"
Steering Wheel
Boot Washer
Nut
Lock Washer
Trim Cover
Bolt – 1/4"-20 x .88" Long
Washer – 1/4"
Hex Nut – 1/4"-20
Hitch Pin
Hairpin Cotter
Flat Washer – .50" I.D.
Key
Operator's Manual
Engine Operator's Manual
Riding Mower Safety Video
Installing the Seat
1.
Mount the seat to the seat base using two 5/16"
shoulder bolts and lock nuts (Fig. 1).
Printed in USA
518xi, 520xi & 522xi Tractor
Model Numbers 73471, 73542,
and 73561—200000001 & Up
QTY.
1
2
2
1
1
1
1
1
2
2
2
1
1
1
2
1
1
1
2.
3.
The Toro Company – 1999
All Rights Reserved
USE
Installing the seat
Installing the steering wheel
Attaching the battery cables
Installing the drawbar hitch pin
Use in ignition and "Key Choice" switches
Read before operating the tractor
Read before operating the tractor
Watch before operating the tractor
Insert the seat switch wire through the center
opening in the seat base (Fig 1).
Push the seat switch wire connector into the wire
harness connector.
Form No. 3323-484
Setup
Instructions

Advertisement

Table of Contents
loading

Related Manuals for Toro 73471

Summary of Contents for Toro 73471

  • Page 1 Form No. 3323-484 518xi, 520xi & 522xi Tractor Setup Model Numbers 73471, 73542, and 73561—200000001 & Up Instructions Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY. Seat Assembly Shoulder Bolt – 5/16” Installing the seat Locknut –...

  • Page 2: Installing The Steering Wheel

    Set-Up Instructions Secure the steering wheel to the shaft with a lock washer and nut (Fig. 2). Tighten the retaining nut to 45–50 ft–lbs. Install the trim cover on the steering wheel. m–3453 Figure 1 1. Seat 5. Seat switch wire connector 2.

  • Page 3: Checking Tire Pressure

    Set-Up Instructions Check to Insure that Steering Checking Tire Pressure Linkage is Centered Check front and rear tire pressure. The correct front and rear tire pressure is 20 psi (138 kPa). With the tractor on a level surface, turn the steering wheel fully to the left and check the clearance of the left hand spindle stop to the stop Activating the Battery...

  • Page 4: Installing The Drawbar Hitch Pin

    Set-Up Instructions 1262 Figure 4 1. Filler caps 3. Lower part of tube 2. Electrolyte 1254 Figure 5 1. Positive battery post 3. Red (+) charger lead 2. Negative battery post 4. Black (–) charger lead POTENTIAL HAZARD Slowly pour electrolyte into each cell until the Charging battery produces gasses.

  • Page 5: Checking The Wiring And Fasteners

    Set-Up Instructions Note: There must be a PTO driven attachment installed to provide a load in order to burnish the clutch facings properly. Run the engine at full throttle and engage the clutch bringing the load to full speed. Then disengage the clutch.
  • Page 6 Set-Up Instructions As applicable, check and test the operation of the following: Engine, choke and throttle controls Gauges Headlights and taillights Indicator lights PTO clutch and brake Lift system Service and parking brakes Transmission controls Steering Tractor operation in forward and reverse Test the operation of the safety interlock system (refer to the tractor Operator’s Manual for the correct procedure).

Table of Contents