Related Manuals for Toro 23511
Summary of Contents for Toro 23511
- Page 1 Form No. 3378-932 Rev A 18in Turf Seeder Model No. 23511—Serial No. 313000001 and Up Model No. 33511—Serial No. 313000001 and Up *3378-932* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Introduction
Note emphasizes general information worthy of special attention. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Whenever you need service, genuine Toro parts, or additional... -
Page 3: Table Of Contents
Contents Safety Introduction ..............2 Improper use or maintenance by the operator or Safety ................3 owner can result in injury. To reduce the potential Safe Operating Practices........... 3 for injury, comply with these safety instructions and Slope Indicator ............5 always pay attention to the safety alert symbol, which Safety and Instructional Decals ......... - Page 4 Replace all worn or damaged decals. into a trailer or truck. • • Use only Toro-approved attachments. The warranty Use care when approaching blind corners, shrubs, trees, may be voided if the machine is used with unapproved or other objects that may obscure vision.
-
Page 5: Slope Indicator
Slope Indicator G011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 20 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 20 degrees. Fold along the appropriate line to match the recommended slope. -
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93–7321 1. Warning—stay away from moving parts; keep all guards in place. - Page 7 127–4061 1. Cutting blades 4. Hold the handle to start the engine. 2. Fast 5. Release the handle to stop the engine. 3. Slow 125–3809 1. Warning—read the Operator’s Manual. 5. Thrown object hazard—keep bystanders away from the machine. 2. Warning—do not operate this machine unless you are trained. 6. Warning—stop the engine before walking away from the machine.
- Page 8 116–8537 117–4979 1. Entanglement hazard, belt—keep away from moving parts; keep all guards and shields in place.
-
Page 9: Setup
Setup Product Overview Unfolding the Handle 1. Raise the handle to the operating position (Figure 4). g023003 Figure 5 1. Operator presence bail 5. Fuel tank 2. Handlebar 6. Seeding rate gauge 3. Throttle control lever 7. Depth control lever 4. -
Page 10: Controls
Controls G023178 Figure 6 1. Recoil-starter 4. Choke lever 2. Sediment cup 5. Throttle lever 3. Fuel shutoff valve Figure 7 Recoil-Starter 1. Throttle lever Pull the recoil-starter handle to start engine (Figure 6). Fuel Shutoff Valve Operator Presence Bail Close the fuel shutoff valve when transporting or storing the The operator presence bail allows the machine to start/run.. - Page 11 Depth Control Lever The depth control lever allows you to set the depth of the cutting blades in 10 cutting positions along with one position for transportation. To adjust the depth, remove the hairpin cotter, pull the locking pin out, and move the lever forward or rearward to the desired depth setting (Figure 9).
-
Page 12: Specifications
Contact an Authorized Service Dealer or Distributor or go Seed Gate Control Lever to www.Toro.com for a list of all approved attachments and accessories. Push the seed gate control lever (Figure 11) forward to start the seed flow, and pull it rearward to stop the seed flow. -
Page 13: Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. Checking the Engine Oil Level Service Interval: Before each use or daily 1. Stop the machine on a level surface. Note: To ensure a more accurate measurement, adjust the depth control lever until the engine is also level. -
Page 14: Starting And Stopping The Engine
Using Stabilizer/Conditioner DANGER Use a fuel stabilizer/conditioner in the traction unit to keep In certain conditions, gasoline is extremely gasoline fresh during storage of 90 days or less. For longer flammable and highly explosive. A fire or explosion storage drain the fuel tank. from gasoline can burn you and others and can Important: Do not use fuel additives containing damage property. -
Page 15: Operating The Machine
Operating the Machine Note: A warm or hot engine may not require choking. 3. Hold down the operator presence bail with one hand. 1. Move the depth control lever to the desired setting. 4. Pull the recoil handle sharply to start the engine. 2. -
Page 16: Maintenance
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Change the engine oil. After the first 25 hours • Check the engine oil level. • Clean debris form the machine. • Inspect the air cleaner elements. • Check the belt tension. If the engine is working but the cutting blades seem Before each use or daily underpowered, check the belt tension. -
Page 17: Engine Maintenance
Engine Maintenance 10. Clean the foam element in warm, soapy water or in a nonflammable solvent. Note: Do not use gasoline to clean the foam element Servicing the Air Cleaner because it could create a risk of fire or explosion. Service Interval: Before each use or daily—Inspect the air 11. -
Page 18: Cleaning The Sediment Cup
1. Disengage the cutting blades, stop the engine by 1. Stop the engine and wait for all moving parts to stop. releasing the operator presence bail, and wait for all 2. Disconnect the wire from the spark plug. moving parts to stop. 3. -
Page 19: Belt Maintenance
Belt Maintenance Checking the Belt Tension Service Interval: Before each use or daily—Check the belt tension. If the engine is working but the cutting blades seem underpowered, check the belt tension. 1. Stop the machine on a level surface, stop the engine Figure 20 by releasing the operator presence bail, disconnect the 1. -
Page 20: Adjusting The Belt Tension
Adjusting the Belt Tension Maintaining the Cutting 1. To tighten the belt, loosen the 4 mounting nuts Blades securing the engine to the frame. Inspecting the Cutting Blades Service Interval: Before each use or daily—Check the cutting blades for wear or damage. When the cutting blades are worn down and are no longer functioning properly;... - Page 21 Figure 23 1. Bolt 5. Spacer 2. Bearing 6. Shaft 3. Washer 7. Nut 4. Blade 8. Loosen and remove the nut and washer from the shaft (Figure 23). 9. Slide the spacer off the shaft (Figure 23). 10. Carefully slide the blades off of the shaft (Figure 23) and replace them as necessary.
-
Page 22: Storage
Storage 5. Check the engine oil level; refer to Checking the Engine Oil Level (page 13). 1. Raise the cutting blades, stop the machine, stop the 6. Fill the fuel tank with fresh gasoline; refer to Adding engine, and disconnect the spark plug wire. Fuel (page 13). - Page 23 Notes:...
- Page 24 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.