Table of Contents
Advertisement
Quick Links
Z Master
with 48in TURBO FORCE
Model No. 74141TE—Serial No. 312000001 and Up
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
© 2012—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Riding Mower
Description
No parts required
No parts required
Rear wheels
Rollover Protection System Kit (ROPS)
Seat
Seat plate
Guard
Flange nuts (5/16 inch)
No parts required
Right control lever
Left control lever
Bolt (3/8 x 1 inch) (2 are assembled)
Nut (3/8 inch)(2 are assembled)
Carriage bolt (3/8 x 1-1/2 inches)
Flange nut (3/8 inch)
Air cleaner cap
Hose clamp
No parts required
No parts required
No parts required
Number 2 general purpose lithium base
or molybdenum base grease. (Purchase
separately.)
No parts required
No parts required
Register at www.Toro.com.
®
Side Discharge Mower
Qty.
–
Remove parts from the crate.
–
Check the tire pressure.
2
Install the rear wheels.
Install the Rollover Protection System
1
(ROPS).
1
1
Install the seat.
2
8
–
Check the seat belt.
1
1
Install the motion control levers.
1
Install the lift assist pedal.
1
1
Install the air cleaner cap.
1
–
Charge and install the battery.
–
Check the engine oil level.
–
Add fuel to the machine.
1 tube
Check the machine for grease.
–
Prepare the side discharge chute.
–
Test the safety interlock system.
Form No. 3372-979 Rev A
Setup Instructions
Use
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro Z Master 74141TE
Summary of Contents for Toro Z Master 74141TE
-
Page 1: Loose Parts
No parts required Prepare the side discharge chute. – No parts required Test the safety interlock system. Register at www.Toro.com. © 2012—The Toro® Company Original Instructions (EN) 8111 Lyndale Avenue South Printed in the USA. Bloomington, MN 55420 All Rights Reserved... -
Page 2: Checking The Tire Pressure
Procedure Description Qty. Check the machine before delivery to – No parts required the customer. Operator's Manual Engine Owner's Manual Registration Card Delivering the machine to the customer. Operator training material Removing Parts from the Crate Raising the Machine Up and Installing the Rear Wheels No Parts Required Parts needed for this procedure:... -
Page 3: Installing The Seat
Installing the Seat Parts needed for this procedure: Seat Seat plate Guard Figure 3 Flange nuts (5/16 inch) 3. Remove the wheel nuts from both sides of the Procedure vehicle and remove the right angle retaining plate. Discard the screws and retaining plate. 1. -
Page 4: Checking The Seat Belt
g017995 Checking the Seat Belt No Parts Required Procedure Important: Ensure the bolt torque is set between 49 to 61 ft-lb (67 to 83 N-m). The seat belt angle and the seat belt bolt torque need to be checked before operating. 1. -
Page 5: Installing The Motion Control Levers
Installing the Motion Control Levers Parts needed for this procedure: Right control lever Left control lever Bolt (3/8 x 1 inch) (2 are assembled) Nut (3/8 inch)(2 are assembled) Procedure 1. Rotate the motion control levers to the upright position. 2. -
Page 6: Installing The Air Cleaner Cap
g016346 Figure 12 Figure 11 1. Lift assist pedal 3. Carriage bolt (3/8 x 1-1/2 2. Remove the air cleaner cap from the machine. inches) 2. Flange nut (3/8 inch) 3. Install the hose clamp onto the air cleaner cap. Installing the Air Cleaner Cap Parts needed for this procedure: Air cleaner cap... -
Page 7: Charging And Installing The Battery
Figure 15 2. Install the battery. Refer to Installing the Battery in the Operator's Manual for instructions. Figure 14 Checking the Engine Oil Level No Parts Required Procedure Charging and Installing the Before you start the engine and use the machine, check Battery the oil level in the engine crankcase;... -
Page 8: Checking The Side Discharge Chute
g017435 Figure 17 Checking the Side Discharge Chute No Parts Required G008942 Procedure Figure 16 If there are plastic ties holding the side discharge chute up, remove them and lower the chute into place. WARNING An uncovered discharge opening could allow the lawn mower to throw objects in the operator's or Checking the Machine for bystander's direction and result in serious injury or... -
Page 9: Testing The Safety Interlock System
Figure 18 1. Grass Deflector 4. L end of spring, place behind deck edge before installing bolt 2. Spring 5. Deck edge 3. J hook end of spring Testing the Safety Interlock System No Parts Required Procedure Before using the machine, test the safety interlock system;... - Page 10 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures.
- Page 11 Delivering the Machine to the Customer Parts needed for this procedure: Operator's Manual Engine Owner's Manual Registration Card Operator training material Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished.
- Page 12 Make sure that the customer receives the Operator's Manual, Engine Owner's Manual, Set Up Instructions, and operator training material. Make sure the customer knows the Parts Catalog is available at www.Toro.com. Assist the customer in loading the mower. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.