hit counter script
Toro Z334 Z Master Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z334 Z Master
  6. Setup instructions
Toro Z334 Z Master Setup Instructions

Toro Z334 Z Master Setup Instructions

Hide thumbs Also See for Z334 Z Master:
Table of Contents

Advertisement

Quick Links

Download this manual
Z334 or Z340 Z Master® Mowers
Model No. For all Z334 or Z340 International Z Master Mowers

Loose Parts

Use the chart below to verify that all parts have been shipped.
Step
1
No parts required
Bolt (3/8 x 1 inch)
2
Nut (3/8 inch)
Right control lever
Left control lever
3
Bolt (3/8 x 1 inch) (2 are assembled)
Curved washer (3/8 inch) (2 are
assembled)
4
No parts required
5
No parts required
Number 2 general purpose lithium
6
base or molybdenum base grease.
(Purchase separately.)
7
No parts required
8
No parts required
9
No parts required
10
No parts required
Operator's Manual
Parts Catalog
Engine Owner's Manual
11
Registration Card
Safety Video
Key
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
Register at www.Toro.com.
Form No. 3357-761 Rev A

Setup Instructions

Qty.
Remove the machine from the
–
crate.
1
Install the seat lanyard.
1
1
1
Install the motion control levers.
4
4
–
Adding fuel to the machine.
–
Charge the battery.
1 tube
Check the machine for grease.
–
Check the engine oil level.
–
Prepare the side discharge chute.
–
Check the hydraulic oil.
Check the machine before delivery
–
to the customer.
1
1
1
Delivering the machine to the
customer.
1
1
2
Original Instructions (EN)
Use
Printed in the USA.
All Rights Reserved

Advertisement

Table of Contents
loading

Related Manuals for Toro Z334 Z Master

Summary of Contents for Toro Z334 Z Master

  • Page 1: Setup Instructions

    Operator’s Manual Parts Catalog Engine Owner’s Manual Delivering the machine to the customer. Registration Card Safety Video Register at www.Toro.com. Original Instructions (EN) © 2006—The Toro® Company Printed in the USA. 8111 Lyndale Avenue South All Rights Reserved Bloomington, MN 55420...

  • Page 2: Removing The Machine From The Crate

    Step 2. Tilt the seat forward and align the lanyard to the hole in the seat base. 3. Install the lanyard to the seat base with a bolt (3/8 x 1 inch) and nut (3/8 inch). 4. Tilt the seat down. Removing the Machine from the Crate No Parts Required...

  • Page 3: Installing The Motion Control Levers

    the neutral position and carefully bend them outward. 5. Move them back to the drive position and check for clearance. 6. Repeat if necessary. Figure 3 1. Nut 3. Bolt 2. Seat retainer bracket Step Figure 4 Installing the Motion Control Levers Parts needed for this step: Right control lever...

  • Page 4: Adding Fuel To The Machine

    Step Adding Fuel to the Machine No Parts Required Procedure Note: Make sure both fuel tanks are half full when first starting the machine. This will prevent Figure 6 air getting into the fuel system and causing starting problems. Add fuel to the machine before starting it. Refer to your Operator’s Manual.

  • Page 5: Checking The Engine Oil Level

    Step Preparing the Side Discharge Chute No Parts Required Procedure 1. Remove the plastic tie holding the side discharge chute up and lower the chute into place. 2. Check the spring at the discharge chute to Figure 7 ensure proper operation. Step Checking the Engine Oil Level...
  • Page 6 4. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 5. Check the expansion tank behind the seat and if necessary add hydraulic oil to the cold line on the side of the tank. 6.
  • Page 7 Step Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
  • Page 8 Step Delivering the Machine to the Customer Parts needed for this step: Operator’s Manual Parts Catalog Engine Owner’s Manual Registration Card Safety Video Procedure At delivery, complete the items listed in the following table and initial each when finished. Model No. Serial No.
  • Page 9 Describe the post sale service procedures for your store. Assist the customer in lling out and mailing the registration card or register online at www.Toro.com Make sure that the customer receives the Operator’s Manual, Parts Catalog, and Engine Owner’s Manual, Set Up Instructions, and safety video.

This manual is also suitable for:

Z340 z master

Table of Contents