hit counter script
Toro Z597 Z Master Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z597 Z Master
  6. Setup instructions
Toro Z597 Z Master Setup Instructions

Toro Z597 Z Master Setup Instructions

Diesel mowers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Z597 Z Master® Diesel Mowers
Model No. For Z597 Diesel Mowers

Loose Parts

Use the chart below to verify that all parts have been shipped.
Step
1
No parts required
2
No parts required
3
Rear wheels
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt (3/8 x 1 inch)
4
Curved washer
Flange nut (3/8 inch)
Bolt (1/2 x 3–1/4 inch)
Flange nut (1/2 inch)
5
No parts required
6
No parts required
Number 2 general purpose lithium
7
base or molybdenum base grease.
(Purchase separately.)
8
No parts required
9
No parts required
10
No parts required
Operator's Manual
Parts Catalog
Engine Owner's Manual
11
Registration Card
Safety Video
Key
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
Register at www.Toro.com.
Form No. 3356-227 Rev A

Setup Instructions

Qty.
–
Remove parts from the crate.
–
Check the tire pressure.
2
Install the drive wheels.
1
1
1
8
Install the Rollover Protection
System (ROPS).
8
8
2
2
–
Adding diesel to the machine.
–
Charge the battery.
1 tube
Check the machine for grease.
–
Check the engine oil level.
–
Prepare the side discharge chute.
Check the machine before delivery
–
to the customer.
1
1
1
Delivering the machine to the
customer.
1
1
2
Original Instructions (EN)
Use
Printed in the USA.
All Rights Reserved

Advertisement

Table of Contents
loading

Related Manuals for Toro Z597 Z Master

Summary of Contents for Toro Z597 Z Master

  • Page 1: Setup Instructions

    Form No. 3356-227 Rev A Z597 Z Master® Diesel Mowers Model No. For Z597 Diesel Mowers Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Step Description Qty. – No parts required Remove parts from the crate.

  • Page 2: Checking The Tire Pressure

    Step Step Removing Parts from the Raising the Machine Up and Crate Installing the Drive Wheels No Parts Required Parts needed for this step: Rear wheels Procedure Procedure Remove the tires and the parts for the ROPS from the shipping crate. 1.

  • Page 3: Installing The Roll Over Protection System

    Step Installing the Roll Over Protection System Parts needed for this step: Roll bar, right section Figure 4 Roll bar, left section Roll bar, center section Bolt (3/8 x 1 inch) Curved washer 4. Mount the wheels with the valve stem to the Flange nut (3/8 inch) outside and secure them with the wheel nuts Bolt (1/2 x 3–1/4 inch)
  • Page 4 Figure 7 3. Lightly oil the ends of the center roll bar section. 4. Loosely install the center roll bar section using 2 bolts (1/2 x 3-1/4 inch) and 2 flange nuts Figure 9 (1/2 inch). Note: Make sure the bolts are installed from the outside of the roll bar.

  • Page 5: Charging The Battery

    Step Charging the Battery No Parts Required Procedure Charging the battery produces gasses that can explode and cause serious injury. • Keep cigarettes, sparks and flames away from the battery. Figure 11 • Make sure the ignition switch is off. •...
  • Page 6 Step Checking the Machine for Grease Parts needed for this step: Number 2 general purpose lithium base 1 tube or molybdenum base grease. (Purchase separately.) Procedure Figure 14 1. Remove the belt covers on domestic machines as shown below. 3. Check the tensioning arm for grease. 4.

  • Page 7: Checking The Engine Oil Level

    Step 6. Check the grease for the cooling fan belt idler arm. 7. Check the grease for the drive belt idler arms. Preparing the Side Discharge Chute No Parts Required Procedure Remove the plastic tie holding the side discharge chute up and lower the chute into place. Figure 16 8.
  • Page 8 Step Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
  • Page 9 Step Delivering the Machine to the Customer Parts needed for this step: Operator’s Manual Parts Catalog Engine Owner’s Manual Registration Card Safety Video Procedure At delivery, complete the items listed in the following table and initial each when finished. Model No. Serial No.
  • Page 10 Describe the post sale service procedures for your store. Assist the customer in lling out and mailing the registration card or register online at www.Toro.com Make sure that the customer receives the Operator’s Manual, Parts Catalog, Engine Owner’s Manual, Set Up Instructions, and safety video.

Table of Contents