SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
GENERAL SPECIFICATIONS CRT Size / Visual Size 14 inch / 357mmV System CRT Type Flat Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Speaker 2 Speaker Position Front Side Size 1.6 x 2.8 Inch Impedance Sound Output 2.5+2.5 W 10%(Typical) 2.0+2.0 W NTSC3.58+4.43 /PAL60Hz...
Page 4
Wake Up Timer Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-DU Control Glow in Dark Remocon Format Toshiba Custom Code TV:40-BFh Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys Keys Keys...
Page 5
GENERAL SPECIFICATIONS G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type Type Auto Search CH Allocation Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Lines Auto CH Memory Hotel Lock Closed Caption Stable Sound...
Page 6
GENERAL SPECIFICATIONS G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Yes(RED) Stand-by On Timer Terminals Front Video Input = VIDEO3 Audio Input = VIDEO3 RCA x 2 Other Terminal...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
Page 8
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 9
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 2-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key Operations VOL.
ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: CONSTANT VOLTAGE Read and perform these adjustments when repairing the Set condition is AV MODE without signal. circuits or replacing electrical parts or PCB assemblies. Connect the digital voltmeter to TP002. Adjust the VR502 until the digital voltmeter is 115 ±...
Page 12
ELECTRICAL ADJUSTMENTS 2-7: VERTICAL POSITION 2-11: TINT/COLOR CENT Receive the monoscope pattern. Receive the color bar pattern. (RF Input) Using the remote control, set the brightness and Connect the oscilloscope to TP806. Using the remote control, set the brightness, contrast, contrast to normal position.
Page 13
ELECTRICAL ADJUSTMENTS 2-12: OSD HORIZONTAL 2-14: CONTRAST MAX MANUAL Activate the adjustment mode display of Fig. 1-1. Receive the color bar pattern. (RF Input) Press the VOL. UP/DOWN button on the remote Using the remote control, set the brightness and contrast to normal position.
ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
Page 20
MICON/TUNER SCHEMATIC DIAGRAM (MAIN PCB) OS101 RPM7138-H5 ACCESORY TU001 TECC1040PG32E TEST POINT CP101 BT001 173979-7 R03(AB)E_20_T R003 I2C_SCL TM101 BT002 SBKMOP006B 330K I2C_SDA R111 R03(AB)E_20_T I2C_OFF H-BUFFER Q102 2SC2412K C003 RED LED V-BUFFER Q101 POWER ON 2SC2412K D109 SLR-342VCT32 MICON IC IC101 OEC7074A FROM/TO CHROMA/IF...
Page 21
CHROMA/IF SCHEMATIC DIAGRAM (MAIN PCB) FROM/TO AV C_V_OUT_SW Y_V_OUT_SW FROM/TO MICON/TUNER TUNER_VIDEO R214 SYNC_OUT TUNER_AUDIO_L AUDIO TUNER_AUDIO_R BUFFER C213 Q201 2SC2412K OSD_B C615 OSD_G R608 OSD_R C212 1/4W W820 FROM AV R205 TV BUFFER 0.01 B OSD_BLK Q202 TV BUFFER CD701B 2SC2412K PROTECT...
Page 22
DEFLECTION SCHEMATIC DIAGRAM (MAIN PCB) V.OUTPUT IC IC401 AN5522 THERMAL PROTECTION PUMP UP 25.0 12.0 25.0 R407 5.6K C411 R414 500V FROM/TO DY 27K +-1% R417 33K V801 CP401 A36AKJ13X05 B06B-DVS W860 C418 FROM POWER 250V 0.27 P.CON+5V H_CTL Q407 HS402 P.CON+9V 2SC2412K...
Page 23
POWER SCHEMATIC DIAGRAM (MAIN PCB) 6.3A 125V CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE 6.3A 125V(F501) ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V(F501) TO DIGITAL COMB/FILTER D516 RELAY DRIVE...
Page 24
SOUND SCHEMATIC DIAGRAM (MAIN PCB) FROM AV R314 SW_AUDIO_R 1.5K R324 C334 SW_AUDIO_L 1.8K 0.033 B R326 C331 C332 100 1/4W 0.022 0.47 R328 1.8K TONE 136K AMP1 I2C BUS INTERFACE SIMAMP1 VOLAMP1 6.5K 6.5K 6.5K VOLAMP2 CONTROL SIMAMP2 6.5K LOGIC TONE 136K...
Page 25
AV SCHEMATIC DIAGRAM (MAIN PCB) TO CHROMA/IF CD701A CH243001 YUV_IN(REAR) J704 MSP-213V1-652_PBSN A/V_OUT(REAR) J708 MSP-213V2-432_PBSN LINE2(REAR) J703 FROM POWER MSP-213V2-432_PBSN L703 P.CON+9V 47uH 0305 C713 R751 C714 R752 FROM/TO DIGITAL COMB C715 SW_VIDEO_OUT R713 LINE1(REAR) J701 C705 Y_V_OUT_COMB BUFFER MSP-213V2-432_PBSN Q709 KANP C_V_OUT_COMB...
Page 30
WAVEFORMS 31 1V 50µs/div 38 50V 20µs/div 39 50V 20µs/div 32 2V 5ms/div 33 2V 5ms/div 34 0.5V 20µs/div 37 50V 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.