COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
XTL-W70 SECTION 3 ELECTRICAL ADJUSTMENTS 3 7 63 1515 0 Inverter Voltage Adjustment MONITOR SECTION Procedure: 1. Press the TV/VIDEO button (S106) to the VIDEO mode, Equipment Used display the gray scale on the monitor screen. The measuring equipment below are used for these electrical 2.
Page 10
XTL-W70 3 7 63 1515 0 Bright Adjustment (2) B and R Level Adjustment Procedure: Procedure: 1. Press the TV/VIDEO button (S106) to the VIDEO mode, 1. Press the TV/VIDEO button (S106) to the VIDEO mode, display the gray scale on the monitor screen.
Page 11
XTL-W70 3 7 63 1515 0 VCOM Amplitude Adjustment Freerun Frequency Adjustment Procedure: Procedure: 1. Press the TV/VIDEO button (S106) to the VIDEO mode, 1. Set the input signal with no signal. display the gray scale screen on the monitor screen.
Page 12
XTL-W70 3 7 63 1515 0 Adjustment Location: RV410: B and R Level Adjustment RV409: B and R Level Adjustment RV405: GAMMA2 Adjustment RV406: GAMMA0,Bright2 Adjustment – MONITOR BOARD (SIDE A) – RV408: Bright1,2 Adjustment TP22 RV407: RGB Gain,Bright2...
XTL-W70 3 7 63 1515 0 TRAP Adjustment TUNER UNIT SECTION Procedure: 1. With the Power off, input the output of TG to TP30 (with DC • Use the following equipment for the electrical adjustment. cut by a capacitor (0.01 µF)).
Page 14
XTL-W70 3 7 63 1515 0 RGB Decoder FO Adjustment DL AMP & DAT Adjustment Procedure: Procedure: 1. Without INPUT1, INPUT2 inputs (no signal input mode), short 1. Adjust DAT so as to minimize the variation between the level the jumper wire between TP100 and GND.
XTL-W70 3 7 6 3 1 5 1 5 0 4-2. BLOCK DIAGRAM — TUNER UNIT (VIDEO) SECTION — VIDEO INPUT SELECTOR IC30 J10-1 VIDEO NAVI IN CN2 (1/2) SONY NAVI (NVX) CONTROL CONTROL BUFFER IC22 (1/2) AUX (V)
XTL-W70 3 7 6 3 1 5 1 5 0 4-4. IC PIN DESCRIPTIONS Pin No. Pin Name Pin Description • IC901 LZ9GJ24 (LCD TIMING CONTROL) MON A Test setting output Pin No. Pin Name Pin Description MON B...
Page 19
XTL-W70 3 7 6 3 1 5 1 5 0 • Waveforms • Waveforms THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. — Monitor Board — — Tuner Board — (In addition to this, the necessary note is printed in each block.)
Page 33
XTL-W70 3 7 63 1515 0 IC13 LA7565EM IC29 BA3121F-T1 OUT1 OUT2 1stT IC3 BA6161F-T1 VIDEO BLOCKING OSCILLATOR IC1 PST9145NL IC50 AT24C01-10SI L 13942296513 – COMP DOUT LOGIC DOUT/ACK TEST SERIAL MUX Y DEC IC17 MM1108XFF EEPROM ADDRESS/COUNTER DATA WORD...
Page 34
XTL-W70 3 7 63 1515 0 IC14 TC74HC4052AF-TP1 IC18 µPD4053BG-T1 B.COM OPEN A.COM C.COM OPEN SELECT A SELECT B OPEN IC31 MSM5258MS-KR1 RESET PAL/NTSC V. DECODER COMP.SYNC 1/525, 1/625 1/19 V. COUNTER H. COUNTER L 13942296513 IC24 CXA1585Q VCC1...
XTL-W70 SECTION 5 EXPLODED VIEWS 3 7 63 1515 0 NOTE: • The mechanical parts with no reference • -XX and -X mean standardized parts, so • Accessories are given in the last of number in the exploded views are not supplied.
XTL-W70 SECTION 6 MONITOR ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since When indicating parts by reference the parts list may be different from the they are seldom required for routine service.
Page 45
XTL-W70 TUNER 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-041-00 METAL CHIP 1/10W R136 1-216-045-00 METAL CHIP 1/10W 1-216-041-00 METAL CHIP 1/10W R137 1-216-073-00 RES-CHIP 1/10W 1-216-041-00 METAL CHIP...
Page 46
XTL-W70 TUNER 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R214 1-216-025-11 RES-CHIP 1/10W R273 1-216-033-00 METAL CHIP 1/10W R215 1-216-021-00 METAL CHIP 1/10W R274 1-216-089-00 RES-CHIP 1/10W R216 1-216-113-00 METAL CHIP...
Page 47
XTL-W70 TUNER 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < FILTER > PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 1-781-823-21 FILTER, SAW 3-310-656-01 TAPE, MAGIC < COIL > 3-310-658-01 TAPE (B), MAGIC...
Page 48
XTL-W70 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.