Advertisement
Quick Links
JY997D29501F
GT10-LDR Memory loader
User's Manual
Manual Number
JY997D29501F
Date
April 2015
This manual describes the part names, dimensions, mounting, and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
Effective April 2015
Specifications are subject to change without notice.
2007 MITSUBISHI ELECTRIC CORPORATION
Safety Precaution
(Read these precautions before using.)
Before using this product, please read this manual and the relevant manuals
introduced in this manual carefully and pay full attention to safety to handle the
product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and
"CAUTION".
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
MOUNTING PRECAUTIONS
Use the memory loader in the environment that satisfies the general
specifications described in GT10 User's manual. Never use the product in
areas with excessive dust, oily smoke, conductive dusts, corrosive gas (salt
air, Cl
, H
S, SO
or NO
), flammable gas, vibration or impacts, or exposed
2
2
2
2
to high temperature, condensation, or rain and wind. Not doing so can cause
an electric shock, fire, malfunction or product damage or deterioration.
STARTUP/MAINTENANCE
PRECAUTIONS
Do not disassemble or modify the memory loader.
Doing so can cause a failure, malfunction, injury or fire.
Do not touch the conductive and electronic parts of the memory loader
directly. Doing so can cause a memory loader malfunction or failure.
When unplugging the cable connected to the GOT, do not hold and pull the
cable portion. Doing so can cause the memory loader or cable to be
damaged or can cause a malfunction due to a cable connection fault.
Do not bent at a sharp angle or tie the memory loader cables.
Doing so can cause the breaking of the cables.
DISPOSAL PRECAUTIONS
When disposing of the product, handle it as industrial waste.
TRANSPORTATION
PRECAUTIONS
Make sure to transport the memory loader and/or relevant unit(s) in the
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of this manual, as they are
precision devices. Failure to do so may cause the unit to fail.
Compliance with EC directive (CE Marking)
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Attention
This product is designed for use in industrial applications.
Authorized Representative in the European Community:
Mitsubishi Electric Europe B.V.
Gothaer Str. 8, 40880 Ratingen, Germany
Requirement for Compliance with EMC directive
The following products have shown compliance through direct testing (to the identified
standards) and design analysis (forming a technical construction file) to the European
Directive for Electromagnetic Compatibility (2004/108/EC) when used as directed by
the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
Standard
Remark
Compliance with all relevant aspects of the
EMI
standard. (Radiated Emissions)
EN61131-2 : 2007
Programmable
Compliance with all relevant aspects of the
controllers-
standard.
Equipment,
EMS
(ESD, RF electromagnetic field, EFTB, Surge, RF
requirement and tests
conducted disturbances and Power frequency
magnetic field)
For more details please contact the local Mitsubishi Electric sales site.
Associated Manuals
The following manuals are relevant to this product. When these loose manuals are
required, please consult with our local distributor.
Manual name
Contents
Describes the GT10 hardware-relevant
content such as part names, external
dimensions, mounting, power supply
GT10 User's Manual
wiring, specifications, and introduction to
option devices.
(sold separately)
GT Designer2
Describes methods of the GT Designer2
Version2 Basic
installation operation, basic operation for
SH-080529ENG
Operation/Data
drawing and transmitting data to
Transfer Manual
GOT1000 series
(For GOT1000 Series)
(sold separately)
GT Designer3
Describes methods of the GT Designer3
Version1 Screen
installation operation, basic operation for
Design Manual
drawing and transmitting data to
(For GOT1000 Series)
GOT1000 series
(Fundamentals)
(sold separately)
Bundled Items
Bundled item
GT10-LDR memory loader
USB cable (1m)
GT10-LDR Memory loader USER'S MANUAL (This manual)
1. Overview
GT10-LDR memory loader is the memory transfer module that reads/writes the data to GT10 or between a PC (GT Designer2 Ver.2.77F or later, GT Designer3 Ver.1.01B or
later) and GT10-LDR.
*1 When GT10-LDR is connected to a PC via the USB hub, the power supply of the USB hub must be supplied by the AC adopter of the USB hub.
GT10-LDR connected to the USB hub may not work properly depending on the PC environment. In the case, connect the GT10-LDR directly to the USB port on the PC.
2. Specifications
2.1 General Specifications
Item
Operating ambient temperature
0 to 40C
Storage ambient temperature
-20 to 60C
*1
Operating ambient humidity
10 to 90% RH, non-condensing
*1
Storage ambient humidity
10 to 90% RH, non-condensing
Manual
Conforms to JIS
Number
Vibration resistance
B3502 and
(Model Code)
IEC61131-2
JY997D24701
Shock resistance
Conforms to JIS B3502, IEC 61131-2 (147 m/s
(09R819)
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles and must be no
Operating atmosphere
direct sunlight. (Same as for saving)
*2
2000 m (6562 ft) max.
Operating altitude
(1D7M24)
Overvoltage category
*3
II or less
Pollution degree
*4
2 or less
Cooling method
Self-cooling
SH-080866ENG
(1D7MB9)
*1 The wet bulb temperature is 39C or less.
*2 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press,
and the sheet may be peeled off.
*3 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
Quantity
*4 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
1
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
1
2.2 Performance Specifications
1
Item
*1
Flash ROM 7.5Mbyte
User memory
Memory
Life (Number of write
100,000 times
times)
POWER
green
LED
SET/RUN
green/red/orange
ERROR
green/red/orange
GT1020, GT1030
USB connecting
cable (supplied)
PC
*1
(GT Designer2 Ver.2.77F or later
GT Designer3 Ver.1.01B or later)
Specifications
Frequency
Acceleration
5 to 9Hz
--
Under intermittent
vibration
9 to 150Hz
9.8m/s
2
5 to 9Hz
--
Under continuous
vibration
9 to 150Hz
4.9m/s
2
2
, 3 times each in X, Y and Z directions)
Specifications
Item
RD/WR selection
switch
Data selection switch
Switch
ENT key
Write protection switch
External dimensions
Weight
*1 ROM in which new data can be written without deleting the written data.
Half-amplitude
Sweep Count
3.5mm
--
10 times each in X, Y
and Z directions
1.75mm
--
Specifications
Paddle switch
Tactile switch
The use of 100 thousand times is due for
replacement.
(operating force 2.55N
0.69N)
Slide switch
W70(2.75)H110(4.33)D21(0.82)[mm](inch)
0.2kg
Advertisement
Related Manuals for Mitsubishi Electric GT10-LDR
Summary of Contents for Mitsubishi Electric GT10-LDR
- Page 1 Make sure to *1 When GT10-LDR is connected to a PC via the USB hub, the power supply of the USB hub must be supplied by the AC adopter of the USB hub.
- Page 2 Described lighting status of ERROR LED (Performs the conversion between USB and serial in Power consumption 0.7W (140mA/DC5V) or less PC communication GT10-LDR. After serial conversion, transmission Transfer cable Cable to be connected with the GOT speed is 115.200bps.) Connector shape...
- Page 3 8.4 Setting GT Designer3 When the communication between a PC (GT Designer2 Ver.2.77F or later, GT Click [ Communication ] [ Communicate with GT10-LDR... ] to display the 7.1 Transfer function Designer3 Ver.1.01B or later) and the memory loader is performed, driver communicate with GT10-LDR screen.
-
Page 4: Troubleshooting
Communication error (SET/RUN LED will be orange.) kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation 4) Press the ENT key to determine the data to be transferred and transfer direction. Check that power supply is stable. (lighting of POWER... - Page 5 Make sure to *1 When GT10-LDR is connected to a PC via the USB hub, the power supply of the USB hub must be supplied by the AC adopter of the USB hub.
- Page 6 Communication error (SET/RUN LED will be orange.) kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation 4) Press the ENT key to determine the data to be transferred and transfer direction. Check that power supply is stable. (lighting of POWER...