Related Manuals for Miele HG02
Summary of Contents for Miele HG02
-
Page 1: Installation Instructions
Installation instructions Dishwasher To prevent accidents and machine damage, read these instructions installation or use. M.-Nr. 05 690 921... - Page 2 3. Install the slide skis ..........12 4. Install the dishwasher under the countertop ......13 5.
- Page 3 Installation, maintenance and re- pair work should be by a Miele authorized service technician. Work by unqualified persons could be a hazard and may void the warranty. This equipment is not designed for maritime use or for use in mobile installations such as caravans or air- craft.
- Page 4 Before installation, make sure the voltage and frequency listed on the data plate correspond with the house- hold electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system.
- Page 5 Toutefois, il peut être parfois possible de faire l’installa- tion de ces applications sous certaines conditions. Veuillez contacter le Con- cessionnaire Miele le plus près de chez-vous ou le Département du servi- ce technique Miele pour leur donner vos exigences précises.
- Page 6 Avant l’installation, s’assurer que la tension et la fréquence énumérées sur la plaque signalétique correspon- dent à la source d’électricité de la rési- dence. Ces données doivent corres- pondre afin d’éviter de vous blesser et d’endommager l’appareil. Consulter un électricien qualifié si vous avez des doutes.
- Page 7 The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Old appliances may contain materials that can be recycled.
- Page 8 (845- 864 mm) are not possible using the supplied legs. For this height range, or for heights greater than 34 " (886 mm), extended legs (part # 02 702 601) are necessary. Contact the Miele Technical Service Department for the appropriate legs. " - 34"...
- Page 9 Machine heights of 35" - 37" (889 - 940 mm) can be obtained if the supplied legs are removed and extended legs are attached. Contact the Miele Technical Service Department for the appropriate legs (part # 02 702 601).
- Page 10 37" (889 - 940 mm) can be obtained if the supplied legs are removed and extended legs are attached. Please contact the Miele Technical Service Department for the appropriate legs (part # 02 702 601). To ensure stability, this dish-...
- Page 11 A stainless steel steam deflector is sup- plied to protect the countertops from steam and condesation when the dish- washer is opened. If the countertop is made of Corian®, granite, marble or other solid, waterproof material, the steam deflector is not required. If the counter is made of different materials, the steam deflector should be positioned so that it cov-...
- Page 12 ^ First, adjust the height of the legs so that the top of the dishwasher is roughly " (3 mm) below the countertop. Tipping the machine slightly to the rear, if possible, will make adjusting the front legs easier.
- Page 13 ^ Make a 2" x 4" (5 x 10 cm) cut out in the side or bottom of the cabinet ad- joining the dishwasher. This cut out is necessary for connections to pass through.
-
Page 14: Level Legs
Make sure the machine is level when adjustments are complete. The dishwasher should be raised until it just touches the underside of the countertop. If you are installing a prefinished unit... - Page 15 ^ Press the "On/Off" button in and place the cover, a, over the push button. ^ Insert the drying vent grill (if applica- ble), b, into its opening. ^ Position the control panel, c, and fasten it from the inside of the door, d, using the six screws provided.
- Page 16 ^ Press the "On/Off" button in and place the cover, a, over the push button. ^ Insert the drying vent grill, b, into its opening. ^ Position the control panel, c, and fasten it from the inside of the door, d, using the six screws provided.
- Page 17 ^ Press the "On/Off" button in and place the cover, a, over the push button. ^ Push the drying vent grill, b, into its opening. ^ Position the control panel, c, and fasten it from the inside of the door, d, using the six screws provided.
- Page 18 The control panel should be aligned with the drawer fronts of the adjoining kitchen cabinets by adjusting the filler strips. ^ Using an 8 mm socket, turn the nut clockwise or counterclockwise until the filler strips line up with the drawer line.
- Page 19 A custom door panel matching the kitchen cabinetry can be installed using the provided templates and bracket. = Panel length = Height to the underside of the countertop = Control panel height* = Toe Kick Height Determined using the following calcula- tion: X = A –...
- Page 20 A custom door panel must not exceed the listed maximum weight. An over- weight panel will distort the door springs causing the dishwasher door to fall when opened. Plastic control 13 lbs panel (5.9 kg) Stainless Steel 10.5 lbs control panel (4.8 kg)
- Page 21 ^ Place a template on each end of the mounting bracket as shown, making sure the rule marks face the outside of the bracket. ^ Hang the mounting bracket on the machine door. ^ Slide the top edge of the templates under the filler strips and control panel.
- Page 22 ^ Tape the bracket to the door panel to hold it in place while the mounting holes are drilled. ^ Drill pilot holes for the screws using a " (2.5 mm) bit. ^ Attach the bracket to the panel using the 6 screws provided.
- Page 23 ^ Attach the panel to the dishwasher by aligning the bracket tabs with the slots on the door. ^ Open the dishwasher door slightly. If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its opening a few inches.
- Page 24 ^ Hang the bracket on the machine door, without the templates. Tighten the four locking screws on the edges of the door panel. ^ Close the door. ^ Measure the distance from the adja- cent cabinet’s (or appliance) door bottom to the bottom of the mounting bracket (X).
- Page 25 ^ Attach the panel to the dishwasher by lining up the bracket tabs with the slots on the door. ^ Open the dishwasher door slightly. If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its opening a few inches.
- Page 26 Do not drill any additional holes through any part of the wash cabi- net. If in doubt on how to secure the dishwasher, please call Miele’s Tech- nical Service Department.
- Page 27 For openings exactly 17 " (60 cm) wide: ^ Open the dishwasher door and re- move the caps covering the mount- ing holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adja- cent cabinets using the supplied screws and bushings.
- Page 28 – turn counterclockwise to de- crease the tension. If the door springs can not be adjusted enough (the door falls), the custom door panel is too heavy. Call your Miele dealer or Miele’s Techni- cal Service Department for advice on stronger door spings.
- Page 29 An air gap is built into the water inlet system to prevent potable water from mixing with waste water. The dishwasher can heat its own water to the temperatures required by the wash program. This allows the option of connecting the machine to either a hot or cold water source.
- Page 30 If the standard " copper plumbing for a dishwasher already exists with a com- pression fitting and valve as pictured: ^ Cut the " copper tubing after the valve. ^ Install the " compression to MHT (Male Hose Thread) adapter (supplied with the machine), as illus- trated.
- Page 31 – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of (22 mm). Drain hose extensions can be ordered from Miele’s Technical Service Department. – A built-in swivel connector allowing the drain hose to be routed in any direction.
- Page 32 ^ Cut off the vent cap located at the right rear of the triple filter system, as illustrated. Since all Miele dishwashers are equipped with an odor trap and non- return valve, the drain hose can be connected directly to the drain pipe as illustrated.
- Page 33 The dishwasher comes equipped with a 4 ft (1.2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle.
- Page 34 The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located. An o- pening through the partition between the compartments of 1 can be made to allow the plug to pass through.
- Page 35 Once the dishwasher is level and se- cured it should be tested. ^ Remove all packing and literature from inside the unit. The yellow Child Safety Lock key hung on the upper basket must be removed before operating the dish- washer.
- Page 36 Before installing the toekick, measure- ments must be taken to ensure that the toekick will not interfere with the com- plete opening of the dishwasher door. The door panel overhang ( ), and toekick depth of recess ( ), determine the maximum dishwasher toekick height ( ).
- Page 37 ^ Insert the mounting bracket with the flange pointing toward the center of the machine. ^ Push the mounting brackets in as far as possible by releasing the tension on the spring clip (see illustration). ^ Insert the mounting bracket with the flange pointing toward the outside of the machine.
- Page 38 The included toekick will fit without modification if the machine is set to its maximum height and the toekick is re- cessed as far as possible (4" / 10 cm). If the machine height is less than maxi- mum, or if the toekick is not recessed 4" (10 cm), the toekick must be shortened.
- Page 39 ^ Carefully open the dishwasher door until it hits the toekick. ^ Using the front lower edge of the door panel as a guide, draw a line across the toekick. ^ Unscrew and remove the toekick. ^ If one of the cutting lines is close to...
- Page 40 Alteration rights reserved (NovoplusB,P,S) / 2702 M.-Nr. 05 690 921 / V This bio-friendly paper was bleached without the use of chlorine.