Page 1: Product Overview
Technical Reference Guide Product Overview Describes features and general specifications for the product. Setup Describes setup and installation of the product and peripherals. Preinstalled OS Information Describes the preinstall information and recovery method. Utility Describes the utilities included in this product and how to use them.
Page 2 • Neither is any liability assumed for damages resulting from the use of the information contained herein. • Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating...
Page 3: For Safety
For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. You must follow warnings carefully to avoid serious bodily injury. WARNING Provides information that must be observed to prevent damage to the equipment or loss of data.
Page 4: Warnings
 Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for advice.  Never attempt to repair this product yourself. Improper repair work can be dangerous.
Page 5: Cautions
Cautions  Do not connect cables in ways other than those mentioned in this manual. Different connections may cause equipment damage or fire.  Be sure to set this equipment on a firm, stable, horizontal surface. CAUTION The product may break or cause injury if it falls. ...
Page 6: Wireless Lan (Ot-Wl01) Important Safety Information
Tampering with this product may result in injury or fire.  The OT-WL01 is only for indoor use.  The OT-WL01 should only be used for EPSON TM-i series and TM-DT. If it is installed on another device, it may result in computer failure, damage, or CAUTION malfunctions.
Page 7 Notes on Security when Using Wireless LAN (Important information on customer rights (maintaining privacy) The advantage of using a wireless LAN over a LAN cable is that, because information is exchanged using radio signals, you can easily connect to the network if you are within range of the radio signals.
Page 8: Powered Usb Hub Unit (Ot-Ph10) Important Safety Information
When the powered USB mode is set to Mode 2, also disconnect the AC cable from the power outlet.  Be sure to attach the USB port cover to the USB ports of the TM-T70II-DT specified in this guide.  Pass the USB cables through the wire saddle to prevent the cables from coming off.
Page 9: About This Manual
About this Manual Aim of the Manual This manual was created to provide information on development, design, and installation of receipt issue systems and development and design of printer applications for developers. Manual Content The manual is made up of the following sections: Chapter 1 Product Overview Chapter 2...
Page 10: Table Of Contents
■ NV Memory (Non-Volatile Memory) ................34 ■ Product Specifications ....................... 36 Power capacity to the exterior......................39 Software Specifications ........................39 Printing Specifications..........................41 Character Specifications........................42 Printable Area............................43 Printing and Cutting Positions......................45 Paper Specifications ..........................46 Environmental Conditions ........................47 External Dimensions..........................48 TM-T70II-DT Dedicated AC Adapter....................49...
Page 11 Powered USB Hub Unit (OT-PH10) ....................... 50 ■ Option Specifications......................51 Wireless LAN Cable Set (OT-WL01) ..................... 51 Customer Display (DM-D110:USB) ...................... 52 Powered USB Hub Unit (OT-PH10) ....................... 53 Setup .....................55 ■ Updating the ePOS-Device ....................55 ■ Flow of Setup ........................56 ■...
Page 12 Preinstallation information .........................126 Storage version ...........................127 Recovery .............................127 Utility....................129 ■ EPSON TMNet WebConfig ....................129 Starting EPSON TMNet WebConfig ....................129 Information - Web service settings - Current status ...............130 Information - System settings - Network ...................132 Information - System settings - Date Time..................134 Settings - Web service settings - Startup settings ................135...
Page 13 Settings - System settings - Wireless LAN (Wireless LAN)..............148 Settings - System settings - TCP/IP (Wireless LAN) ................149 Settings - System settings - SSL ......................150 Settings - System settings - Time Setting ..................151 Settings - System settings - Shutdown settings ................152 Settings - Admin settings - Store/restore settings................
Page 14 ■ Printer Operation ......................188 Printer Reset ............................188 Setting and Replacing Roll Paper ....................188 Removing Jammed Paper ........................190 ■ Adjusting the Speaker Volume ..................190 ■ Cleaning the Case ......................190 ■ Cleaning the Thermal Head.................... 191 ■ Preparing for Transport..................... 192 Appendix ..................193 ■...
Page 15 Page 47 (WPC1253: Greek) ......................229 Page 48 (WPC1254: Turkish)......................230 Page 49 (WPC1255: Hebrew) ......................231 Page 50 (WPC1256: Arabic) ......................232 Page 51 (WPC1257: Baltic Rim)......................233 Page 52 (WPC1258: Vietnamese)....................234 Page 53 (KZ1048: Kazakhstan) ......................235 Page 255 (User-Defined Page) ......................
Page 17: Product Overview
This chapter describes features and specifications of the product. Features The TM-T70II-DT is a highly-functional printer that has an auxiliary storage and a Windows- operated controller in the thermal receipt printer TM-T70II. It can control POS peripherals such as customer displays, TM printers, and barcode scanners. The following is its features.
Page 18: Features Of This Printer
Features of this printer • High speed printing (250 mm/s maximum) is possible. • Multi-tone graphic printing is possible. • Easy drop-in paper loading • A maintenance counter function is supported. • Paper-saving function is supported.
Page 19: System Connection Examples
You can configure a simple POS system by installing POS applications and connecting a display with a touch panel and a barcode scanner to the TM-T70II-DT. The OS is based on Windows and includes SATA SSD. You can install the Windows driver (APD) and the UPOS driver.
Page 20 Printing and controlling POS peripherals from the Web application ePOS-Device API is supported. You can print or control devices (display on the customer display or input/output from the POS peripherals) from the Web application. You can control the customer display, barcode scanner, USB devices, or the serial device from the same API system.
Page 21 Chapter 1 Product Overview Printing and controlling POS peripherals from an application on a tablet terminal ePOS-Device XML is supported. You can print or control devices (display on the customer display or input / output from the POS peripherals) from a tablet terminal application. You can control the customer display, barcode scanner, USB devices or serial devices from the same system.
Page 22 Communication between applications This function is supported by ePOS-Device API / ePOS-Device XML. Communication between applications is enabled by the function of communication box. • ePOS-Device API Supports communication between web applications. Enables communication between web applications on devices such as a smart phone and tablet terminal. •...
Page 23 Chapter 1 Product Overview Acquiring data from a server at a remote location (via Internet or any other means) and printing the acquired data This product supports the Server Direct Print function, with which the printer requests data from the Web server and prints the acquired data. Your application can print data only by sending back the print data in response to a request from the printer.
Page 24 Virtual environment client You can use the product as a client of a virtual desktop or virtual application. It supports Citrix XenServer/Client, VM Ware, and Microsoft's Hyper-V/App-V. Printing is supported for applications that use the UPOS driver and APD (Windows driver).
Page 25: Product Configurations
Chapter 1 Product Overview Product Configurations Models The following models are prepared for this product. The model varies depending on the region for sale. Main Auxiliary Model memory storage Windows Embedded High 1.86GHz SATA SSD(16GB) POSReady 7 Windows Embedded 1.6GHz SATA SSD(16GB) POSReady 2009 Paper width...
Page 26: Accessories
Accessories Included • AC adapter, T (Model No. M284A) • AC cable *1 • Connector cover • Roll paper (for operation check) • Screws x3 • Two strips for the roll paper guide • Screw for the roll paper guide •...
Page 27: Related Manuals
Chapter 1 Product Overview Related manuals • TM-T70II-DT Technical Reference Guide (this manual) • TM-T70II-DT User’s Manual • ePOS-Device API User’s Manual • ePOS-Device XML User’s Manual • Server Direct Print User’s Manual • TM-DT Thin-Client System Setup Guide • TM-DT series Easy Setup Guide For details about each system, refer to "Application Development Information"...
Page 28: Part Names And Functions
Part Names and Functions Manual cutter Controller LED Cover open lever Power button Control panel Printer reset button Roll paper cover Name Description Power button Turns the product on or off. Keep pressing the power button to turn off the product forcibly. Printer reset button Resets the printer unit.
Page 29: Control Panel
Chapter 1 Product Overview Control Panel Feed button Paper LED Error LED (Power) LED Name Status Description Feed button Pressing this button once feeds the roll paper by one line. Holding this button down feeds the roll paper continuously. Paper LED There is a sufficient amount of roll paper remaining There is little or no roll paper remaining Flashing...
Page 30: Storage Access Led
Storage access LED These display the controller unit’s status. Name Status Description Status LED  Power is on (green) Flashing  Stand-by mode (Approx. 1 second intervals) Power is off Status LED  Flashing  OS start-up sequence  Accessing the storage;  (orange) (Approx.
Page 31: Connectors
Chapter 1 Product Overview Connectors All the cables are connected to the connection panel on the back of the printer. DisplayPort (only for High model) Line-Out Ethernet Serial DC-In Drawer-kick Name Description Drawer-kick Connect the cash drawer here. Ethernet Connect the printer to the network. Connect external devices with USB interface here.
Page 32: Printer Function
Printer function Error Status There are three possible error types: automatically recoverable errors, recoverable errors, and unrecoverable errors. Check the error LED flash code. Automatically Recoverable Errors Printing is no longer possible when automatically recoverable errors occur. They can be recovered easily, as described below.
Page 33: Unrecoverable Errors
Chapter 1 Product Overview Unrecoverable Errors Printing is no longer possible when unrecoverable errors occur. The printer must be repaired. Turn off the power immediately when unrecoverable errors occur. CAUTION Error LED flash code Error Error description Approx. 160 ms Memory R/W error After R/W checking, the printer does not work correctly.
Page 34: Nv Memory (Non-Volatile Memory)
NV Memory (Non-Volatile Memory) The printer's NV memory stores data even after the printer power is turned off. NV memory contains the following memory areas for the user: • NV graphics memory • User NV memory • Memory switches • R/E (Receipt Enhancement) •...
Page 35: Maintenance Counter
Chapter 1 Product Overview R/E (Receipt Enhancement) Graphics, such as shop logos to be printed on top or bottom of receipts can be registered. For information about R/E, see "Setting the Memory Switches/Receipt Enhancement" on page User-defined Page You can store character data in the user-defined page (character code table: page 255) so that you can also print characters not resident in the printer.
Page 36: Product Specifications
Product Specifications • High model (Page • Low model (Page High model Item Specifications  Usable CPU Intel Atom Processor N2800 (1MB Cache, 1.86 GHz) Memory Main memory 4 GB, DDR3-1066, SO-DIMM slot BIOS SPI Flash 4MB  Chipset Intel NM10 Video controller On built-in CPU...
Page 37 Chapter 1 Product Overview External dimensions 172 mm {6.77”}(W) x 290 mm {11.42”}(D) x 114 mm {4.49”}(H) (inclusive of cable cover) Case color White / Black 2.8 kg {6.17 lb} Weight (Mass) (roll paper excluded)
Page 38 Low model Item Specifications  Usable CPU Intel Atom Processor N2600 (1MB Cache, 1.6 GHz) Memory Main memory 2 GB, DDR3-800, SO-DIMM slot BIOS SPI Flash 4Mbyte  Chipset Intel NM10 Video controller On built-in CPU Auxiliary storage SATA SSD (16GB) Interface Ethernet 10BASE-T/100BASE-TX/1000BASE-T 1port (RJ-45)
Page 39: Power Capacity To The Exterior
DC 24V Drawer Software Specifications Print control ePOS-Device API, ePOS-Device XML, Server Direct Print (No printer driver is required.) APD 5.00 (Windows printer driver for TM-T70II-DT) TM Printer, POS peripherals control driver Web applications Available server-side scripts:  PHP ver.5.4.5 ...
Page 40  Following printers with the UB-E02, UB-E03, UB-R03, or UB-R04  Controllable TC Model printer embedded  TM-T88V  TM-T70  TM-T70II  TM-T90  TM-L90  TM-H6000IV  TM-P60II  Following printers with the UB-E02, UB-E03, UB-R03, or UB-R04  SA Model embedded ...
Page 41: Printing Specifications
Chapter 1 Product Overview Printing Specifications Printing method Thermal line printing Cutting method Partial cut (cutting one point in left edge left uncut) Dot density 180 × 180 dpi Printing direction Unidirectional with friction feed (Reverse feed is not supported.) Printing width 72.2 mm (2.84"), 512 dots Characters per line...
Page 42: Character Specifications
Character Specifications Font A  Number of characters Alphanumeric characters: 95 Extended graphics: 128 × 43 pages  (initial setting) Font B (including user-defined page) International characters: 18 sets Font A  Character structure 12 × 24 (including 2-dot horizontal spacing) (initial setting) Font B 9 ×...
Page 43: Printable Area
Chapter 1 Product Overview Printable Area 80 mm paper width printing The printable area of paper with a width of 79.5 ± 0.5 mm {3.13 ± 0.02"} is 72.2 ± 0.2 mm {2.84 ± 0.008"} (512 dots), and the space on the right and left sides is approximately 3.7 mm {0.15"}. All the numeric values are typical.
Page 44 58 mm paper width printing The printable area of paper with a width of 57.5 ± 0.5 mm {2.26 ± 0.02"} is 50.8 ± 0.2 mm {2.00 ± 0.008"} (360 dots), and the space on the left side is approximately 3.7 mm {0.15"} and the space on the right side is approximately 3.0 mm {0.12"}.
Page 45: Printing And Cutting Positions
Chapter 1 Product Overview Printing and Cutting Positions Manual-cutter position Approx. 30 mm Approx. 13 mm Autocutter blade position Center of the print dotline Paper feed direction [units: mm (All the numeric values are typical.)] The values above may vary slightly as a result of paper slack or variations in the paper. Take this into account when setting the cutting position of the autocutter.
Page 46: Paper Specifications
Paper Specifications Paper types Specified thermal paper Form Roll paper Size Roll paper diameter 83 mm {3.27"} maximum Roll paper core Inside: 12 mm {0.47"}, Outside: 18 mm {0.71"} Roll width when taken up 80 + 0.5/-1.0 mm Paper width 79.5 ±...
Page 47: Environmental Conditions
Standby (max.):  approximately 42 dB (Standing Operator position) Note: The values above are measured in the Epson evaluation condition. Acoustic noise differs depending on the paper used, printing contents, and the setting values, such as print speed or print...
Page 48: External Dimensions
External Dimensions • Width: Approximately 172 mm {6.77"} • Depth: Approximately 290 mm {11.42"} • Height: Approximately 114 mm {4.49"} [Units: mm]...
Page 49: Tm-T70Ii-Dt Dedicated Ac Adapter
Chapter 1 Product Overview TM-T70II-DT Dedicated AC Adapter 1500 33.5 24.3 [Units: mm] Input conditions Input voltage: AC 100V to 240V Frequency: 50/60 Hz Input current (rating): 2.4A Output conditions Output voltage (rating): DC 24V ± 5% Output current (rating): 4.2A...
Page 50: Powered Usb Hub Unit (Ot-Ph10)
Powered USB Hub Unit (OT-PH10) • Width: Approximately 141 mm {5.55"} • Depth: Approximately 161 mm {6.34"} • Height: Approximately 46.5 mm {1.83"} 40.5 46.5 [Units: mm]...
Page 51: Option Specifications
Chapter 1 Product Overview Option Specifications Wireless LAN Cable Set (OT-WL01) Wireless module ELPAP07: 802. 11b/g/n wireless LAN Module (EPSON) Standard IEEE802.11b/g/n (Wi-Fi certificated) SSID 1 to 32 one-byte alphanumeric characters Connection mode Ad hoc mode, Infrastructure mode Authentication method, Encryption...
Page 52: Customer Display (Dm-D110:Usb)
165(W) x 50.5(D) x 69(H) mm dimensions Base 165(W) x 110(D) x63(H)mm Dimensions 165(W) x 110(D) x135(H)mm Weight 0.31 kg {0.68 lb} Color Black Tilt angle Maximum 48°(4 steps, 5 position) Morizontal rotation angle Maximum 90° Power supply Supplied from TM-T70II-DT Option Pole unit (DP-105)
Page 53: Powered Usb Hub Unit (Ot-Ph10)
*1,*2, *3 Interface Powered USB External: x 3 (Power supply: 12 V/5 V USB cable x 1 (for connecting with TM-T70II-DT (for upstream)) DC Power cable x 1 (for connecting with TM-T70II-DT Powered USB Mode 1 Interlock with TM-DT power button, output the USB power...
Page 55: Setup
""System connection examples" on page Confirming the ePOS-Device version You can confirm the version of the ePOS-Device on the EPSON TMNet WebConfig title bar. Downloading the ePOS-Device update program Download the following file from the Epson website and save it in your local environment.
Page 56: Flow Of Setup
Flow of Setup Setup for this product and the external devices vary depending on the system configuration method. In this setup flow, necessary items are in a frame with a solid line. Optional items are explained in an frame with a dotted line. PC-POS System Installing the Product (page 60) Attaching the Optional Powered USB Hub Unit (page 63)
Page 57 Chapter 2 Setup If using ePOS-Device API (Controling the printing and external devices from a Web application) Installing the Product (page 60) Attaching the Optional Powered USB Hub Unit (page 63) Connecting the AC Adapter (page 65) OS Initial Settings (page 74) Connecting to the Network (page 78) Service Startup Settings (page 88) Registering Web content (page 93)
Page 58 If using ePOS-Device XML (Controling the printing and external devices from a terminal application) Installing the Product (page 60) Attaching the Optional Powered USB Hub Unit (page 63) Connecting the AC Adapter (page 65) OS Initial Settings (page 74) Connecting to the Network (page 78) Service Startup Settings (page 88) Registering device control script files (page 94) Attaching the Optional Customer Display (page 95)
Page 59 Chapter 2 Setup If using Server Direct Print  (printing via Internet or from a remote location) Installing the Product (page 60) Attaching the Optional Powered USB Hub Unit (page 63) Connecting the AC Adapter (page 65) OS Initial Settings (page 74) Connecting to the Network (page 78) Service Startup Settings (page 88) Server Direct Print Settings (page 90)
Page 60: Installing The Product
Installing the Product You can install this printer only horizontally. Fix the printer so that it does not move around when you open the roll paper cover and cut roll paper. A tape for fixing the printer is available as an option. ...
Page 61: Important Notes
Chapter 2 Setup Important Notes • The Product must be installed horizontally on a flat surface (not tilted). • Firmly fix the printer so that it does not move when you open or close the roll paper cover or when the roll paper is cut. •...
Page 62: Security Hook
Security Hook You can attach a commercially available security wire to the security hook. Security hook...
Page 63: Attaching The Optional Powered Usb Hub Unit
Description Power is supplied/not supplied for the powered USB ports when the power of the TM-T70II-DT is turned on/off, in accordance with the operation of the power button of the TM-T70II-DT. Power is always supplied for the powered USB ports regardless of the operation of the power button of the TM-T70II-DT.
Page 64 Place the USB port cover provided with the powered USB hub unit over the USB ports of TM-T70II-DT (as shown below). Any failure without the USB port cover is not covered by the support warranty. It is recommended to place the product behind the TM-T70II-DT.
Page 65: Connecting The Ac Adapter
Chapter 2 Setup Connecting the AC Adapter Use the dedicated AC adapter for TM-T70II-DT provided with the printer.  Be sure to use the included AC adapter as the power supply unit. Using a nonstandard power supply can result in electric shock and fire.
Page 66 When using the powered USB hub unit For the optional powered USB hub unit (OT-PH10), connect the AC adapter to the location show below.
Page 67: Setting The Memory Switches/Receipt Enhancement
Chapter 2 Setup Setting the Memory Switches/Receipt Enhancement With the memory and R/E (receipt enhancement) function, which are software settings for this printer, you can set the various functions. For an outline of the functions, see the following section. Use the methods shown in the table below;...
Page 68: Functions
✔ ✔ Auto top logo (Excluding some functions) ✔ ✔ Auto bottom logo ✔ ✔ Auto top/bottom logo extended functions (Excluding some functions) *: Not used for this product.  For information about the TM-T70II Utility, see the TM-T70II Utility User’s Manual. ...
Page 69: Auto Line Feed
Chapter 2 Setup Auto line feed • Always disabled(initial setting) • Always enabled USB power-saving function  Disabled  Enabled (initial setting) The USB power-saving function is valid only when the USB interface communication condition is set to the vendor-defined class and the system configuration is set so that the USB driver can support the USB power-saving fuction.
Page 70: Print Speed
Multi-tone print density Selectable from levels 1 to 13 (70% ~ 130%) Initial setting: level 7 (100%)  First change the print density, and then configure the Multi-tone density.  In you set the density too high, the contrast becomes lower. Select the density level checking the overall tone balance of your image.
Page 71 Chapter 2 Setup Autocutting after closing cover • Cuts • Does not cut (initial setting) Paper reduction Extra upper space reduction • Disabled (initial setting) • Enabled Extra lower space reduction  Disabled (initial setting)  Enabled Line space reduction rate •...
Page 72 Font A auto replacement • Does not replace (initial setting) • Font B Font B auto replacement • Does not replace (initial setting) • Font A Buzzer Do not change the default setting. Communication conditon of USB interface • USB printer class •...
Page 73 Chapter 2 Setup Auto bottom logo Key-code Selectable from key-codes of registered logos Alignment • Left (initial setting) • Center • Right Auto top/bottom logo extended functions TM-T70II Utility does not supported the following functions.  Top logo print while paper feed to the cutting position ...
Page 74: Os Initial Settings
The OS desktop is displayed. Select [Start], then [Control Panel], and [Date and Time]. The "Date and Time" window is displayed. Set the time, date, and the timezone. You can also set the date, time, and the timezone using EPSON TMNet WebConfig.
Page 75: Setting For Display
Chapter 2 Setup Setting for Display Using display,perform setting using the following procedure. This setting is a function enabled only for Windows Embedded POSReady7. Connect display this product’s VGA port. Click [Start] then [Control Panel], and execute [All Control Panel Items] - [Display] - [Screen Resolution].
Page 76 From the “Multiple displays” list, select “Show desltop only on 2”. Click [OK].
Page 77: Enabling Or Disabling Epos-Device
Chapter 2 Setup Enabling or Disabling ePOS-Device Use the desktop shortcut to enable or disable ePOS-Device. Enable it if you are using ePOS-Device. API, ePOS-Device XML, or Server Direct Print  If you enabled ePOS-Device, it uses 100 MB or more of memory. If you are using this product with a PC-POS system or in a virtual environment, we recommend disabling e-POS-Device.
Page 78: Connecting To The Network
Connecting to the Network For Ethernet Interface Connect the product to a network by a LAN cable via a hub. Connecting the Ethernet interface cable  When LAN cables are installed outdoors, make sure devices without proper surge protection are cushioned by being connected through devices that do have surge protection.
Page 79: Network Settings
You can perform settings in the following ways. • Setting in a local environment: Setting with Windows Setting with EPSON TMNet WebConfig • Setting on a PC for setting: Setting with EPSON TMNet WebConfig If you perform settings in a local environment, connect a display, a keyboard, and a mouse with this product.
Page 80 EPSON TMNet WebConfig Run [Disabling ePOS-Device] from the shortcut on the desktop. Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 81: For Wireless Lan Interface
Chapter 2 Setup For Wireless LAN Interface The optional wireless LAN cable set (OT-WL01) enables you to use the product with a wireless LAN connection. Connecting the wireless LAN cable set Check whether the following items are included. If any item is damaged, contact your dealer. •...
Page 82 Connect the USB extension cable to the USB connector of the printer. If you want to fix the wireless LAN unit, cut the included affixing tape to fit and put on the unit, and fix the unit in a place with good communication. Wireless LAN indicator The position of the wireless LAN indicator is shown in the illustration below.
Page 83 You can perform settings in the following ways. • Setting in a local environment: Setting with Windows Setting with EPSON TMNet WebConfig • Setting on a PC for setting: Setting with EPSON TMNet WebConfig If you perform settings in a local environment, connect a display, a keyboard, and a mouse with this product.
Page 84 Infrastructure settings (Windows Embedded POSReady 2009) Click [Start], then [Control Panel]. Run "Network Connections". The Network Connections window is displayed. Right-click [Wireless Network Connection], and select [Properties]. The "Wireless Network Connection" window is displayed. Click on the [Wireless Networks] tab. Click [Add].
Page 85 Chapter 2 Setup Ad hoc settings (Windows Embedded POSReady 2009) Click [Start], then [Control Panel]. Run "Network Connections". The "Network Connections" window is displayed. Right-click [Wireless Network Connection], and select [Properties].  The "Wireless Network Connection" window is displayed. Click on the [Wireless Networks] tab, and click [Advanced]. Select [Computer-to-computer (ad-hoc) networks only], then click [Close].
Page 86 Setting with EPSON TMNet WebConfig Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 87: Installing The Driver And Applications
Chapter 2 Setup Installing the Driver and Applications Installing the Drivers You need to download and install a driver that is compatible with the control method and the device to be controlled. The Windows driver (APD Ver.5 for TM-T70II) for the products printer has been installed in this product.
Page 88: Service Startup Settings
Service Startup Settings It is necessary to perform service setup settings for the TM-T70II-DT depending on the system operation method. Use EPSON TMNet WebConfig to perform the service setup settings, following the procedures below. Run EPSON TMNet WebConfig from shortcut on the desktop....
Page 89 Chapter 2 Setup Set the following, then click [Apply]. Item Description Device control Set whether to control POS peripherals using this product or not. Automatic update of Set whether to use the automatic update for Web content or not. Web content Server direct print Set whether to use the server direct print or not.
Page 90: Server Direct Print Settings
Server Direct Print Settings Use EPSON TMNet WebConfig to perform the Server Direct Print Settings, following the procedures below. Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 91: Registering Web Contents
Chapter 2 Setup Registering Web Contents Perform registration as follows, depending on the system and method in use. If placing Web content in this product's Web server using ePOS-Device API or Server Direct Print, register the Web content. When you upload Web content, the existing registered Web content is discarded.  (The folders under U_data remain.) Specifications of the file to be registered •...
Page 92 • When you access to registered web contents from an input terminal and so on, the URL differs depending on the folder structure of the zip file. ➀ http://[the product’s IP address]/index.html ➁ http://[the product’s IP address]/webpage/index.html ➀ ➁ epsonsample.zip epsonsample.zip index.html webpage ......
Page 93: Registering Web Content
Chapter 2 Setup Registering Web content Use EPSON TMNet WebConfig to register Web contents on this product, following the procedures below. Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 94: Registering Device Control Script Files
Registering device control script files Use EPSON TMNet WebConfig to register device control scripts on this product, following the procedures below. This registration is used when registering device control script files, such as serial communication devices, using ePOS-Device. Run EPSON TMNet WebConfig from shortcut on the desktop....
Page 95: Attaching The Optional Customer Display
Chapter 2 Setup Attaching the Optional Customer Display Setting the Customer Display DM-D110 has the DIP switches. The functions are follows. • Displaying self-test • Setting the communication speed (Serial communication) In normal use, you do not need to change the settings. If you change this setting, match the setting to that of the product.
Page 96: Connecting The Customer Display
Communication Speed Switching Communication Speed SW1-5 SW1-6 SW1-7 (bps) 2400 4800 9600 19200 38400 57600 115200 (Reserved) How to set the DIP switch Disconnect the cable connecting the DM-D110. Remove the DIP switch cover. Switch the switch with something pointy. Close the DIP switch cover.
Page 97: Connecting External Devices
Chapter 2 Setup Connecting External Devices When connecting an external device to a USB connector, be sure to check this product and the device's manual for the amount of power consumed by the external device. CAUTION  Connect external devices as necessary. ...
Page 98: Connecting A Printer
USB connectors, and install the drivers for each model. For details such as the order in which to connect them, refer to each device's user's manual. • You can perform the connection test from EPSON TMNet WebConfig. For details, refer to"Set- ting the Devices" on page 101.
Page 99: Connecting The Cash Drawer
Connecting the Cash Drawer When using a cash drawer, connect the cash drawer. Use the cash drawer handled by EPSON or your dealer. Connecting the Drawer-kick Cable  Specifications of drawers differ a great deal, depending on makers or models.
Page 100 Drawer Connection Circuitry Shielded drawer-kick connector Drawer-kick solenoid +24V Control device Drawer open/close switch Printer side User side [Drawer-kick side]...
Page 101: Setting The Devices
Setting the Devices Registering a Printer Use EPSON TMNet WebConfig to register a network printer on this product, following the procedures below. This product's printer is already registered, so settings are not necessary. Run EPSON TMNet WebConfig from shortcut on the desktop....
Page 102 Set the following, then click [Add]. The information for the registered device is displayed in [Registered printers]. Item Description Set the device ID for the printer you want to register. (Any character Device ID string) Type Select network printer. Model no. Select the printer model.
Page 103: Customer Display Settings
Chapter 2 Setup Customer Display Settings Use EPSON TMNet WebConfig to register the dedicated customer display DM-D110, following the procedures below. Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 104 Select [Use] and perform the following settings. Item Description Used for customer display communication settings. If you changed the DM-D110 (dedicated model) dip switch settings, Communication  change the communication settings in accordance with those settings changes. (If you do not change the dip switch settings, use the default settings.) Set the brightness of the customer display in percentages.
Page 105: Registering A Key Input Device
Chapter 2 Setup Registering a Key Input Device Use EPSON TMNet WebConfig to register a key input device on this product, following the procedures below. Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 106 Set the following, then click [Add]. The information for the registered device is displayed in [Registered key input device]. Item Description Device ID Set the device ID for the key input device you want to control. Select the key input device model. Device name Unregistered key input devices that are currently connected to the unit are listed.
Page 107: Serial Communication Device Registration
Chapter 2 Setup Serial Communication Device Registration Use EPSON TMNet WebConfig to register a serial communication device with this product, following the procedures below. Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 108 Select the product name or port for the serial communication device. Item Description Physical serial port This is the serial port on the back of this product. These are the USB ports on the back of this product. If connecting a serial device using a COM-USB cable, select the corresponding USB port.
Page 109 Chapter 2 Setup Item Description Control script Select the control script to control the serial communication device. Communication  Select the communication speed. speed (bps) Data bit Select the data bit. Parity Select the parity. Stop bit Select the stop bit. Flow control Select whether there is flow control or not.
Page 110: Registering Other Devices
Registering Other Devices Use EPSON TMNet WebConfig to register other devices on this product, following the procedures below. Run EPSON TMNet WebConfig from shortcut on the desktop. EPSON TMNet WebConfig is started. If you perform settings from an external device, enter the following in the URL field of your Web browser (such as the address bar).
Page 111 Chapter 2 Setup Set the following, then click [Add]. The information for the registered device is displayed in [Other registered devices]. Item Description Device ID Set the device ID for the device you want to control. Control script Select the control script to control the other devices.
Page 112: Printer Settings
It is recommended to write all logos together in the printer when you register more than one logo. Select [Start] - [All Programs] - [EPSON] - [TM-T70II Software] -  [TM-T70II Utility], and starting the TM-T70II Utility. Select [Storing Logos], and then click [Add].
Page 113 Chapter 2 Setup Specify the image data file for logo. The file must be smaller than W: 2047  H: 831 pixels (dots) in bmp, jpeg, gif, or png format. If the logo width exceeds the paper width (80 mm printing: 512 dots, 58 mm printing: 360 dots), an error message appears.
Page 114 Edit the image data checking the preview window on the right, and then click [OK]. Item Description Set whether you will resize the image or not and the image size after resizing. (Units: mm) Resize If the image size is wider than the paper width and it is not resized, the part out of the paper width will not be printed.
Page 115 Chapter 2 Setup When you register more than one logo, repeat the Steps 1 to 6. After registering all logo data, check the indicator on the right to make sure that the data size is small enough to write in the printer, and then click [Store to Printer].
Page 116: Attaching The Connector Cover
Attaching the Connector Cover Attach the connector cover to protect the cables by following the steps below. Align the tab on the connector cover with the dent on the main body. Push the connector cover with the dent on the main body. Make sure the cables are not pinched.
Page 117: Attaching The Power Button Cover
Chapter 2 Setup Attaching the Power Button Cover Attach the power button cover that comes with the product onto the power button to prevant accidental operation of the power button. Follow the steps below to attach the power button cover. It is recommended to clean the area around the power button with a cloth mistened with alcohol before you attach the cover.
Page 119: Preinstalled Os Information
 Intel Graphics Media Accelerator 3600 Series Driver GPIO Driver Broadcom Network Driver Conexant Sound Driver EPSON Advanced Printer Driver 5.00 EPSON TM printer Communication module Customer Display COM-USB Driver ePOS-Device and related software Tool EPSON TMNet WebConfig WriteFilter Utility...
Page 120: Storage Version
To verify the storage version, see HDVER.TAG in the root directory of the startup drive. This file is in text format and can be viewed using Notepad, etc. The contents of HDVER.TAG are as follows. [HD Information] MODEL=TM-T70II-DT OS=POSReady7 LANG=English VER=2.xx.xx Recovery Follow the steps below to perform the recovery.
Page 121 Chapter 3 Preinstalled OS Information A confirmation message that says "All data on disc will be deleted. Do you really want to start recovery?" is displayed. Click [Yes]. Recovery is performed. After the recovery procedure, the system automatically shuts down. The system automatically restarts several times for Windows initialization.
Page 122: Settings For Dual Display
Settings for Dual Display If using dual display, perform settings using the following procedure. This setting is a function enabled only for Windows Embedded POSReady 7. Connect displays this product's VGA port and display port. Click [Start] then [Control Panel], and execute [All control Panel Items] - [Display] - [Screen Resolution].
Page 123 Chapter 3 Preinstalled OS Information  Click [Intel Graphic Media Accelerator Driver] tab. Click [Graphics Properties...].  The "Intel Graphics Media Control Panel" windows is displayed.
Page 124 Click [Multiple Displays]. From the “Operating Mode” list, select “Clone Displays” or “Extended Desktop”. Click [OK].
Page 125: Using Os Hibernation
Chapter 3 Preinstalled OS Information Using OS Hibernation  This setting is a function enabled only for Windows Embedded POSReady 7.  Perform these settings using a user account with administrator privileges.  If you use hibernation, a system file the same size as the main memory is created by the OS.
Page 126: Windows Embedded Posready 2009
SATA AHCI Driver  Intel Embedded Media and Graphics Driver GPIO Driver Broadcom Network Driver Conexant Sound Driver EPSON Advanced Printer Driver 5.00 EPSON TM printer Communication module Customer Display COM-USB Driver ePOS-Device and related software Tool EPSON TMNet WebConfig WriteFilter Utility...
Page 127: Storage Version
To verify the storage version, see HDVER.TAG in the root directory of the startup drive. This file is in text format and can be viewed using Notepad, etc. The contents of HDVER.TAG are as follows. [HD Information] MODEL=TM-T70II-DT OS=POSReady2009 LANG=English VER=2.xx.xx Recovery Follow the steps below to perform the recovery.
Page 128 A confirmation message that says "All data on disc will be deleted. Do you really want to start recovery?" is displayed. Click [Yes]. Recovery is performed. The "***INSTALL COMPLETED***" message is displayed. After that, the "Press any key to continue..." message is displayed.
Page 129: Utility
The following explains the utilities equipped in this product. EPSON TMNet WebConfig Starting EPSON TMNet WebConfig Start EPSON TMNet WebConfig using the method below. Connect a display and keyboard to the product.  Log in as the Administrator. Start TMNet WebConfig from the shortcut on the desktop. ...
Page 130: Information - Web Service Settings - Current Status
Information - Web service settings - Current status You can check the basic settings for this product. Item Description Administrator name Displays the administrator name for this prod- uct. Admin information Installation location Displays the installation location for this prod- uct.
Page 131 Chapter 4 Utility Item Description Run state Displays the run state of the server direct print. Displays the web server ID acquiring print data of the server direct print. Interval (sec.) Displays the interval for acquiring print data. Server direct print Displays the date and time last run of the Date and time last run server direct print.
Page 132: Information - System Settings - Network
Information - System settings - Network You can check the network settings for this product. Item Description IP address Displays this product's IP address for a wired LAN network. Subnet Mask Displays the subnet mask. Default Gateway Displays the default gateway. TCP/IP Information Acquire DNS Ser ver Address Displays whether the Acquire DNS Ser ver...
Page 133 Chapter 4 Utility Item Description Displays this product's IP address for a wireless IP address LAN network. Subnet Mask Displays the subnet mask. Default Gateway Displays the default gateway. TCP/IP Information Displays whether the Acquire DNS Ser ver (Wireless LAN) AcquireDNS Server Address Address Automatically function is enabled or Automatically...
Page 134: Information - System Settings - Date Time
Information - System settings - Date Time You can check this product's time settings. Item Description Date and Time Displays the time and the timezone set for this product. Automatically adjust clock Displays whether the automatic daylight saving time adjustment func- for Daylight Saving Time tion is enabled or not.
Page 135: Settings - Web Service Settings - Startup Settings
Chapter 4 Utility Settings - Web service settings - Startup settings Performs startup settings for various Web service functions. Item Description Enables or disables device control functions that use Web service.  Device control Used for ePOS-Device. Automatic update of Web Enables or disables the automatic update function for Web content.
Page 136: Settings - Web Service Settings - Printer
Settings - Web service settings - Printer Performs the settings for printers controlled by this product. Item Description Device ID Set the ID for the controlled printer. (Any character string) Type Select the type for the controlled printer. Model no. Select the model number for the controlled printer.
Page 137 Chapter 4 Utility Oparating test Item Description Receipt Test printing Performs a test printing. “TEST_PRINT” is printed. Slip Start printing Performs a slip printing test. “TEST_PRINT” is printed. Cancel printing Cancels printing. Endorsement Start printing Performs an endorsement printing test. “TEST_PRINT” is printed. Cancel printing Cancels printing.
Page 138: Settings - Web Service Settings - Customer Display
Settings - Web service settings - Customer Display Performs the settings for the customer display controlled by this product. Item Description Do not use Do not use a customer display. Use a customer display. Communication  Communication  Set the communication speed. settings speed (bps) Data bit...
Page 139: Settings - Web Service Settings - Key Input Device
Chapter 4 Utility Settings - Web service settings - Key input device Performs the settings for the key input device controlled by this product. Item Description Device ID Set the ID for the key input device. Device name Set the device name for the key input device. Control script Set the device control script to control the key input device.
Page 140: Settings - Webservice Settings - Serial Communication Device
Settings - Webservice settings - Serial communication Device Performs the settings for serial communication devices controlled by this product. Item Description Device ID Set the device ID. Device name Model selection Select the device model name. Port selection Select the device port. Control script Select the device control script for controlling the serial communi- cation device.
Page 141 Chapter 4 Utility Item Description Registered serial  Displays a list of registered serial communication devices. communication device Detailed  Displays the device settings confirmation window. display Operating test Performs an operating test for a registered serial communication device. Delete Deletes a registered serial communication device.
Page 142: Settings - Webservice Settings - Other Device
Settings - Webservice settings - Other Device Performs settings for other devices controlled by this product. Item Description Device ID Set the ID for the controlled device. Control script Set the device control script to control the device. Registers the device on this product. Other registered devices Displays other devices registered on this product.
Page 143: Settings - Webservice Settings - Control Script - Add/Delete
Chapter 4 Utility Settings - Webservice settings - Control script - Add/delete Performs registration or deletion for device control scripts used by this product. Item Description Control script Set the control script to be registered. Click [Browse] to display the "Choose File to Upload" window. Select the file to be used.
Page 144: Settings - Webservice Settings - Web Content - Update Settings
Settings - Webservice settings - Web content - Update settings Performs settings for the installation method and update settings for the Web content registered on this product. Item Description A u t o m a t i c Update schedule Set the schedule for automatic update of the Web con- update settings tent.
Page 145: Settings - Webservice Settings - Server Direct Print
Chapter 4 Utility Settings - Webservice settings - Server Direct print Performs TCP/IP settings for this product's server direct print. Item Description Specify the user name to be used for Digest authentication for the server. The specified value is also passed as the ID parameter value of the form data to be posted to the server.
Page 146: Settings - Webservice Settings - Status Notification
Settings - Webservice settings - Status notification Performs TCP/IP settings for this product's status notification. Item Description Specify the user name to be used for Digest authentication for the server. The specified value is also passed as the ID parameter value of the form data to be posted to the server.
Page 147: Settings - System Settings - Tcp/Ip (Wired Lan)
Chapter 4 Utility Settings - System settings - TCP/IP (Wired LAN) Performs TCP/IP settings for this product's wired LAN. Item Description Get IP Address Selects [Auto] or [Manual] for the method for acquiring the IP address. Specifies the IP address. IP Adderess Only enabled when the method for acquiring the IP address is [Manual].
Page 148: Settings - System Settings - Wireless Lan (Wireless Lan)
Settings - System settings - Wireless LAN (Wireless LAN) Performs settings for this product's wireless LAN. Item Description Network Mode Specifies this product's network mode. SSID Specifies the SSID for the wireless LAN network. Authentication Method Specifies the authentication method for the wireless LAN network. Security Mode Specifies the encryption method for the wireless LAN network.
Page 149: Settings - System Settings - Tcp/Ip (Wireless Lan)
Chapter 4 Utility Settings - System settings - TCP/IP (Wireless LAN) Performs TCP/IP settings for this product's wireless LAN. Item Description Get IP Address Selects [Auto] or [Manual] for the method for acquiring the IP address. Specifies the IP address. IP address Only enabled when the method for acquiring the IP address is [Manual].
Page 150: Settings - System Settings - Ssl
Settings - System settings - SSL Performs SSL settings for this product. Item Description Disable Disables SSL authentication. Remove the certificate Select this checkbox to delete the SSL certificate. Enable Enables SSL authentication. Update the certificate To update the SSL certificate, select this checkbox and specify the following files: ...
Page 151: Settings - System Settings - Time Setting
Chapter 4 Utility Settings - System settings - Time Setting Performs time settings for this product. Item Description Date and time Sets the time. Time Zone Sets the area. Sets the time difference from Coordinated Universal Time. Automatically adjust clock for Selects whether to automatically adjust the clock for Daylight Sav- Daylight Saving Time ing Time.
Page 152: Settings - System Settings - Shutdown Settings
Settings - System settings - Shutdown settings Performs shutdown settings for this product. Item Description When the power button is pressed Set the operation when you press the power button. ePOS-Device Shutdown permission Specify the permission settings for shutdown from ePOS- Device.
Page 153: Settings - Admin Settings - Store/Restore Settings
Chapter 4 Utility Settings - Admin settings - Store/restore settings Saves and restores various settings for this product. Item Description Acquire Acquires the setting file for this product. Specify a local file Setting file Specify the location of the local setting file. Specify a file URL Setting file URL Specify the URL of the setting file.
Page 154 Restored items Items to be restored in the [Restore the settings] are as follows. Item Availability  Device control Startup settings  Automatic update of Web content Available  Server direct print  Status notification Registered   Device ID Printer device ...
Page 155 Chapter 4 Utility Item Availability Server   ID Server direct  access  Password print Available  URL  Interval  ID Status   Password notification Available  URL  Interval Wired   Get IP Address TCP/IP Settings  ...
Page 156 Item Availability  When the power button is pressed Shutdown  Power  Shut down permission settings Available  Password protection  Specify the local file to use/Specify the file URL M a i n t e - S a v e / r e s t o r e nance settings to use...
Page 157: Settings - Admin Settings - Initialization
Initializes the Web service settings for this product. Item Description Initialize Initializes the Web service settings. If you initialize the Web service, the password for EPSON TMNet WebConfig will also be initialized. The initial values are below. User name: epson Password: epson...
Page 158: Settings - Admin Settings - Log
Settings - Admin settings - Log Acquires this product's log file. Item Description Acquires this product's log file. Acquire a log file...
Page 159: Settings - Admin Settings - Update Web Service Function
Chapter 4 Utility Settings - Admin settings - Update Web service function Updates the Web service function used in this product. Item Description Specify the local Update file Specify the local file for updating. file to use Specify the file Update file URL Specify the URL of the file for updating.
Page 160: Settings - Admin Settings - Admin Information
Settings - Admin settings - Admin information Sets the administrator information for this product. Item Description Administrator name Set the administrator name. Installation location Set the installation location. Apply Registers the settings to this product.
Page 161: Settings - Admin Settings - Password
After setting the password, you will be asked for your user name and password on the cer- tification screen displayed when this utility starts. Input "epson" for the user name and input the set password for the password. The initial value for the password is "epson".
Page 162: Tm-T70Ii Utility
TM-T70II Utility This TM-T70II Utility is provided as a utility for setting this product's printer. You can set the following. • Operating Check • Storing Logos • Paper Reduction settings • Automatic Paper Cut settings • Printing Control settings • Font settings •...
Page 163: Application Development Information
This chapter explains the control method for printers and necessary information for developing applications that use this product. Development Information for Each System TM-T70II-DT application development information varies based on the system. • PC-POS System • ePOS-Device API • ePOS-Device XML •...
Page 164: Pc-Pos System Development Information
This system uses the same development environment as a Windows PC. Interfaces and External Devices Category Device Interface Description Printer TM-T70II-DT Recognized as a USB-connection TM- (This products  T88V. printer) TM printer TM printer connected to this product via an USB interface.
Page 165: Control Method For Devices
Chapter 5 Application Development Control Method for Devices The followings are methods for controlling devices. • ESC/POS command: This can control the EPSON TM printer, cash drawer, and customer display. (For details, refer to "ESC/POS command" on page 166.) • APD5 (Windows printer driver):...
Page 166: Esc/Pos Command
ESC/POS command ESC/POS is the Epson original printer command system. With ESC/POS commands, you can directly control all the TM printer functions, but detailed knowledge of printer specifications or combination of commands is required, compared to using a driver. For detailed information about ESC/POS commands, see the ESC/POS Command Reference.
Page 167 Chapter 5 Application Development Define/delete user-defined characters Cancel print data in page mode Commands for panel buttons Enable/disable panel buttons Commands for paper sensors Select paper sensor(s) to stop printing Select paper sensor(s) to output paper-end signals Commands for print positions Horizontal tab Set horizontal tab positions Set left margin...
Page 168 Print downloaded bit image Define the Windows BMP in the NV graphics memory Define downloaded Windows BMP NV graphics Commands for status Enable/disable Automatic Status Back (ASB) Transmit status Transmit real-time status Commands for barcode Print barcode Set barcode height Set barcode width Select print position of HRI characters Select font for HRI characters...
Page 169 Chapter 5 Application Development MaxiCode: Store the data in the symbol storage area MaxiCode: Print the symbol data in the symbol storage area MaxiCode: Transmit the size information of the symbol data in the symbol storage area Two-dimensional GS1 DataBar: Set the width of module Two-dimensional GS1 DataBar: Set the maximum width of GS1 DataBar Expanded Stacked Two-dimensional GS1 DataBar: Store the data in the symbol storage area Two-dimensional GS1 DataBar: Print the symbol data in the symbol storage area...
Page 170 Initialize printer Transmit printer ID Set horizontal and vertical motion units Select peripheral device Generate pulse to drawer Generate pulse to drawer in real-time Execute power-off sequence Clear buffer(s) Enable/disable real-time command Send real-time request to printer Select page mode Select standard mode Set the process ID response Execute test print...
Page 171: Software
EPSON Advanced Printer Driver Ver.5 (APD5):  APD5 Printer Manual This driver is the Windows printer driver dedi-  APD5 Status API Manual cated for TM-T70II-DT, and pre-installed on the  APD5 Printer Specification product.  APD Install Manual EPSON Advanced Printer Driver Ver.4 (APD4) ...
Page 172 Basic, unlike ordinary Windows drivers. It is not a driver to be used for printing from commercial applications. *3: This guide describes not only Epson-specific functions, but also general information on how to control printers using the OPOS ADK (in the chapter POS Printer and...
Page 173: Epos-Device Api
The following is information as of January, 2014. For the latest information, refer to the ePOS- Device API User's Manual. Printer ❏ TM-T70II-DT: This product's printer ❏ Network printer: TM printer connected to the same network as this product. Applicable models: ...
Page 174 Key input device Device with the device control script prepared in advance ❏ MSR ❏ Bbarcode scanner ❏ USB keyboard device You must acquire the device control script files for the following devices ❏ Input device that can operate with the OS standard HID driver Serial communication device You must acquire the device control script files for the following devices ❏...
Page 175: Application Information
• Web server in the network • Web server via the Internet If registering a Web application on the TM-T70II-DT, use EPSON TMNet WebConfig to register Device control Specify a device ID for each device. The initial value for the device ID for this product's printer is "local_printer".
Page 176: Epos-Device Xml
The following is information as of January, 2014. For the latest information, refer to the ePOS- Device XML User's Manual. Printer ❏ TM-T70II-DT: This product's printer TM printer connected to the same network as this product.  ❏ Network printer: Applicable models: ...
Page 177 Chapter 5 Application Development Key input device Device with the device control script prepared in advance ❏ MSR ❏ Barcode scanner ❏ USB keyboard device You must acquire the device control script files for the following devices ❏ Input device that can operate with the OS standard HID driver Serial communication device You must acquire the device control script files for the following devices ❏...
Page 178: Application Information
Specify a device ID for each device. The initial value for the device ID for this product's printer is "local_printer". You do not need to specify one for DM-D110 (dedicated model). Device ID for the dedicated customer display is fixed to "local_display". Make the control setting with EPSON TMNet WebConfig.
Page 179: Server Direct Print
The following is information as of January, 2014. For the latest information, refer to the Server Direct Print User's Manual. Printer ❏ TM-T70II-DT: This product's printer ❏ Network printer: TM printer connected to the same network as this product. ...
Page 180: Application Information
Device control Specify a device ID for each device. The initial value for the device ID for this product's printer is "local_printer". Specify any device ID for a network printer. Use EPSON TMNet WebConfig for these settings and registration.
Page 181: Setting/Checking Modes
Chapter 5 Application Development Setting/Checking Modes Besides the normal print mode, the printer has the following modes to set or check settings of the printer. • Self-test Mode • Hexadecimal Dumping Mode • NV Graphics Print Mode • Receipt Enhancement Information Print Mode •...
Page 182: Self-Test Mode
Self-test Mode You can confirm the following information by running the self-test mode. • Control software version • Receive buffer size • Busy conditions • Built-in character sets • Print density • Maintenance Information (Print head running length, count of autocutting) Follow the steps below to run this mode.
Page 183: Hexadecimal Dumping Mode
Chapter 5 Application Development Hexadecimal Dumping Mode In the hexadecimal dumping mode, the printer prints the data transmitted from a host computer in hexadecimal numbers and their corresponding characters. Follow the steps below to run this mode.  If there is no character corresponding to print data, “.” is printed. ...
Page 184: Nv Graphics Print Mode
NV Graphics Print Mode You can confirm the following information by running NV graphics print mode: • Capacity of the NV graphics • Used amount of the NV graphics • Unused capacity of the NV graphics • Number of NV graphics that are registered •...
Page 185: Receipt Enhancement Information Print Mode
Chapter 5 Application Development Receipt Enhancement Information Print Mode You can confirm the following information by running the receipt enhancement (R/E) information mode: • Automatic top logo setting • Automatic bottom logo setting • Extended settings for automatic top/bottom logo Follow the steps below to run this mode.
Page 186: Memory Switch Setting Mode
Memory Switch Setting Mode You can configure the memory switches of the printer.  Receive buffer capacity  BUSY condition  Processing when data receive error  Auto line feed  USB power-saving function  Release condition of receive buffer BUSY ...
Page 187: Handling
Chapter 6 Handling Handling This chapter explains how to handle the TM-T70II-DT. Turning the Power On/Off Turning the Power On Use the power button to turn on the power for this product. You can also turn on the power via the network.
Page 188: Printer Operation
Printer Operation Printer Reset Keep pressing this button with a pointed object (such as a pen) until the Power LED goes off to reset the printer unit. Printer reset button Setting and Replacing Roll Paper  Do not open the roll paper cover during printing. Doing so may damage the printer.
Page 189 Chapter 6 Handling If there is a used roll paper core, remove it. Be careful of the rolling direction, and set the roll paper in the printer. Pull the roll paper out towards you, and close the roll paper cover. Cut the end of the roll paper using the manual cutter.
Page 190: Removing Jammed Paper
Adjusting the Speaker Volume You can adjust the speaker volume with the speaker volume adjustment function of the OS included in the TM-T70II-DT. Cleaning the Case Turn off the printer before cleaning the case, and wipe the dirt off the case with a dry or slightly damp cloth.
Page 191: Cleaning The Thermal Head
Chapter 6 Handling Cleaning the Thermal Head Epson recommends cleaning the thermal head periodically (generally every 3 months) to maintain the receipt print quality. After printing, the thermal head can be very hot. Do not touch it and let it cool before you clean it.
Page 192: Preparing For Transport
Preparing for Transport Follow the steps below to transport the product. Turn off the product. Remove the peripherals and the power connector. Remove the roll paper. Remove the customer display. Pack the product upright.
Page 193: Appendix
Appendix Appendix Character Code Tables  The character code tables show only character configurations. They do not show the actual print pattern.  “SP” in the table shows a space. Common to All Pages When International character set (See "International Character Sets" on page 237.) is USA: "...
Page 194: Pc437: Usa, Standard Europe]
Page 0 [PC437: USA, Standard Europe] Ç É á ░ └ ╨ α ≡ í ü æ ▒ ┴ ╤ β ± Γ é Æ ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ ä ö ñ...
Page 195: Katakana)
Appendix Page 1 (Katakana)
Page 196: Pc850: Multilingual)
Page 2 (PC850: Multilingual) Ç É á ░ └ ð Ó í ü æ ▒ ┴ Ð β ± é Æ ó ▓ ┬ Ê Ô â ô ú │ ├ Ë Ò ¾ ä ö ñ ┤ ─ È õ...
Page 197: Pc860: Portuguese)
Appendix Page 3 (PC860: Portuguese) Ç É á ░ └ ╨ α ≡ í ü À ▒ ┴ ╤ β ± Γ é È ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ ã õ ñ ┤...
Page 198: Pc863: Canadian-French)
Page 4 (PC863: Canadian-French) Ç É ¦ ░ └ ╨ α ≡ ü È ´ ▒ ┴ ╤ β ± Γ é Ê ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ Â Ë ¨ ┤ ─...
Page 199: Pc865: Nordic)
Appendix Page 5 (PC865: Nordic) Ç É á ░ └ ╨ α ≡ í ü æ ▒ ┴ ╤ β ± Γ é Æ ó ▓ ┬ ╥ ≥ â ô ú │ ├ ╙ π ≤ ä ö ñ ┤...
Page 200: Pc851: Greek)
Page 11 (PC851: Greek) Ί ϊ Ç ░ └ Τ ζ ΐ ü ▒ ┴ Υ η ± é Ό ó ▓ ┬ Ф θ υ ι â ô ύ │ ├ Χ Φ ä ö ┤ ─ à ┼ Ω...
Page 201: Pc853: Turkish)
Appendix Page 12 (PC853: Turkish) Ç É á ░ └ Ó í ü ▒ ┴ β é ó ▓ ┬ Ê Ô â ô ú │ ├ Ë Ò ä ö ñ ┤ ─ È ı à ò Ñ Á ┼...
Page 202: Pc857: Turkish)
Page 13 (PC857: Turkish) Ç É á ░ └ Ó í ü æ ▒ ┴ β ± é Æ ó ▓ ┬ Ê Ô â ô ú │ ├ Ë Ò ¾ ä ö ñ ┤ ─ È õ ¶ à...
Page 203: Pc737: Greek)
Appendix Page 14 (PC737: Greek) ι ░ └ ╨ Σ ▒ ┴ ╤ ± Г ▓ ┬ ╥ ≥ Υ μ │ ├ ╙ ≤ ϊ Ï Ф ┤ ─ ╘ ί ╡ ┼ ╒ ╢ ╞ ╓ ó ÷ Θ...
Page 204: Iso8859-7: Greek)
Page 15 (ISO8859-7: Greek) ΐ ° π ‘ ± α ’ ² β Γ £ ³ Σ σ τ ´ Τ δ Υ ε υ Ф ζ ¦ • Χ η § ¨ Θ θ Ι ι © Ω Ί Ϊ...
Page 205: Wpc1252)
Appendix Page 16 (WPC1252) ° À Ð à ð ¡ ± Á Ñ á ñ ¢ ² Â Ò â ò ƒ £ ³ Ã Ó ã ó ´ ¤ Ä Ô ä ô • ¥ Å Õ å õ ¦...
Page 206: Pc866: Cyrillic #2)
Page 17 (PC866: Cyrillic #2) ░ └ ╨ ▒ ┴ ╤ ▓ ┬ ╥ Г г │ ├ ╙ Ї Ф ┤ ─ ╘ ї ╡ ┼ ╒ ╢ ╞ ╓ ╖ ╟ ╫ ╕ ╚ ╪ ° ╣ ╔ ┘...
Page 207: Pc852: Latin2)
Appendix Page 18 (PC852: Latin2) Ç É á ░ └ Ó í ü ▒ ┴ Ð β ĺ é ó ▓ ┬ Ô â ô ú │ ├ Ë ä ö ┤ ─ Á ┼ § Í Â ÷ Î ç...
Page 208: Pc858: Euro)
Page 19 (PC858: Euro) Ç É á ░ └ ð Ó í ü æ ▒ ┴ Ð β ± é Æ ó ▓ ┬ Ê Ô â ô ú │ ├ Ë Ò ¾ ä ö ñ ┤ ─ È õ...
Page 209: Ku42: Thai)
Appendix Page 20 (KU42: Thai) ┌ ┐ └ ┘ │ ─ ├ ┤ ┴ ┬ ┼ █...
Page 210: Tis11: Thai)
Page 21 (TIS11: Thai) ┌ ┐ └ ─ ┘ ┴ │ ┬ ├ ┼ ┤...
Page 211: Tis18: Thai)
Appendix Page 26 (TIS18: Thai) ┌ ┐ └ ┘ │ ─ ├ ┤ ┴ ┬ ┼ █...
Page 212: Tcvn-3: Vietnamese)
Page 30 (TCVN-3: Vietnamese) é ê õ ó ú à ô ã â á â ê ô è ý ò ù...
Page 213: Tcvn-3: Vietnamese)
Appendix Page 31 (TCVN-3: Vietnamese) É Â Ê Õ Ó Ú À Ô Ã Â Ð Á Ê Ô È Ý Ò Ù...
Page 214: Pc720: Arabic)
Page 32 (PC720: Arabic) ░ └ ╨ ≡ ▒ ┴ ╤ é ▓ ┬ ╥ â ô │ ├ ╙ ¤ ┤ ─ ╘ à ╡ ┼ ╒ û ╢ ╞ ╓ ç ù ╖ ╟ ╫ ≈ ° ê ╕...
Page 215: Wpc775: Baltic Rim)
Appendix Page 33 (WPC775: Baltic Rim) É ░ └ Ó ü æ ▒ ┴ ± é Æ ó ▓ ┬ │ ├ ¾ ä ö ┤ ─ õ ¶ ┼ Õ § å ¢ ÷ ¦ © ╚ ° Ö ®...
Page 216: Pc855: Cyrillic)
Page 34 (PC855: Cyrillic) ░ └ ▒ ┴ ▓ ┬ │ ├ ┤ ─ ┼ ╚ ╣ ╔ ┘ ║ ╩ ┌ Ф ╗ ╦ █ г ╝ ╠ ▄ Г ═ § « ╬ ■ » ┐ ¤ ▀...
Page 217: Pc861: Icelandic)
Appendix Page 35 (PC861: Icelandic)
Page 218: Pc862: Hebrew)
Page 36 (PC862: Hebrew)
Page 219: Pc864: Arabic)
Appendix Page 37 (PC864: Arabic) ° β ¢ · ∞ · √ ± £ ▒ ½ ¤ ─ ¼ │ ≈ ┼ « ┤ » ┬ ├ ┴ ¦ ┐ ¬ ┌ ÷ └ × ■ ┘...
Page 220: Pc869: Greek)
Page 38 (PC869: Greek) Ί ϊ ░ └ Τ ζ ΐ ▒ ┴ Υ η ± Ό ▓ ┬ Φ θ υ ι ϕ ύ │ ├ Χ ┤ ─ ┼ Ω § Γ α μ © β · ╚ °...
Page 221: Iso8859-2: Latin2)
Appendix Page 39 (ISO8859-2: Latin2) ░ └ ° Ð ▒ ┴ Á á ▓ ┬ Â â │ ├ Ó ó ┤ ─ ¤ ´ Ä Ô ä ô   ┘ ┼ ┌ ▄ Ö ö █ ▀ Ç ×...
Page 222: Iso8859-15: Latin9)
Page 40 (ISO8859-15: Latin9)
Page 223: Pc1098: Farsi)
Appendix Page 41 (PC1098: Farsi) ░ └ ‫ﺥ‬ ▒ ┴ ▓ ┬ │ ├ ┤ ─ ┼ ‫ﻐ‬ ‫ﻑ‬ ╚ ╣ ╔ ┘ ║ ╩ ┌ ╗ ╦ █ ╝ ╠ ▄ ‫ﺃ‬ ═ × « ╬ ■ » ┐ ▀...
Page 224: Pc1118: Lithuanian)
Page 42 (PC1118: Lithuanian)
Page 225: Pc1119: Lithuanian)
Appendix Page 43 (PC1119: Lithuanian) ░ └ ▒ ┴ ▓ ┬ ≥ Г г │ ├ ≤ Ф ┤ ─ ┼ ÷ ≈ ╚ ° ╣ ╔ ┘ · · ║ ╩ ┌ ╗ ╦ █ √ ╝ ╠ ▄ ═...
Page 226: Pc1125: Ukrainian)
Page 44 (PC1125: Ukrainian) ░ └ ╨ ▒ ┴ ╤ ▓ ┬ ╥ Г г │ ├ ╙ Ф ┤ ─ ╘ ╡ ┼ ╒ ╓ ╢ ╞ ╫ ╖ ╟ ╪ ╕ ╚ ╣ ╔ ┘ ÷ ║ ╩ ┌...
Page 227: Wpc1250: Latin 2)
Appendix Page 45 (WPC1250: Latin 2) ° ± Á á Â â Ó ó ¤ ´ Ä Ô ä ô • ¶ Ö ö ¦ × · Ç ç ÷ § ¨ ¸ © É é ú Ú « » Ë...
Page 229: Wpc1253: Greek)
Appendix Page 47 (WPC1253: Greek) ° π ΅ ± α ² β Γ ƒ £ ³ Σ σ τ ¤ Τ δ • ¥ Υ ε υ ϕ ¶ Φ ζ ¦ · Χ η § ¨ Θ θ Ι ι...
Page 230: Wpc1254: Turkish)
Page 48 (WPC1254: Turkish) ° À à ¡ ± Á Ñ á ñ ¢ ² Â Ò â ò ƒ £ ³ Ã Ó ã ó ¤ ´ Ä Ô ä ô • ¥ Å Õ å õ ¶ Æ Ö...
Page 231: Wpc1255: Hebrew)
Appendix Page 49 (WPC1255: Hebrew) ° ¡ ± ¢ ² ƒ £ ³ ´ • ¥ ¶ ¦ · § ¨ ¸ © ¹ × ÷ « » ¬ ¼ ½ ® ¾ ¯ ¿...
Page 232: Wpc1256: Arabic)
Page 50 (WPC1256: Arabic) ° à ، ± ¢ ² â ƒ £ ³ ¤ ´ ô • ¥ ‫ﺽ‬ ¶ ¦ × · ç ÷ § ‫ﻁ‬ ¨ ¸ è © ¹ é ù ê « » ë û ¬...
Page 233: Wpc1257: Baltic Rim)
Appendix Page 51 (WPC1257: Baltic Rim) ° ± ¢ ² £ ³ Ó ó ¤ ´ Ä ä • Å Õ å õ ¶ Ö ö ¦ × · ÷ § Ø ø © ¹ É é ‹ « » ¬...
Page 234: Wpc1258: Vietnamese)
Page 52 (WPC1258: Vietnamese) ° À à ¡ ± Á Ñ á ñ ¢ ² Â â ƒ £ ³ Ó ó ¤ ´ Ä Ô ä ô • ¥ Å å ¶ Æ Ö æ ö ¦ · Ç ×...
Page 235: Kz1048: Kazakhstan)
Appendix Page 53 (KZ1048: Kazakhstan) ° Ұ ± ұ Г г Ə ¤ ө Ф • Ө ¶ ¦ · § © Ғ ғ « » ¬ ə Қ қ Ң Һ һ ® ң Ү ү...
Page 236: User-Defined Page)
Page 255 (User-Defined Page)
Page 237: International Character Sets
Appendix International Character Sets ASCII code (Hex) Country ¥ France à ° ç § é ù è ¨ Germany § Ä Ö Ü ä ö ü β U.K. £ ¥ Denmark I Æ Ø Å æ ø å Sweden ¤ É...

Epson TM-T70II-DT Technical Reference Manual

For Safety

Restriction of Use

About this Manual

Contents

Product Overview

Features

Product Configurations

Part Names and Functions

Printer Function

NV Memory (Non-Volatile Memory)

Product Specifications

Option Specifications

Setup

Updating the Epos-Device

Flow of Setup

Installing the Product

Attaching the Optional Powered USB Hub Unit

Connecting the AC Adapter

Setting the Memory Switches/Receipt Enhancement

OS Initial Settings

Enabling or Disabling Epos-Device

Connecting to the Network

Installing the Driver and Applications

Service Startup Settings

Server Direct Print Settings

Registering Web Contents

Registering Device Control Script Files

Attaching the Optional Customer Display

Connecting External Devices

Setting the Devices

Printer Settings

Attaching the Connector Cover

Removing the Connector Cover

Attaching the Power Button Cover

Preinstalled os Information

Windows Embedded Posready 7

Windows Embedded Posready 2009

Utility

EPSON Tmnet Webconfig

TM-T70II Utility

Application Development Information

Development Information for each System

PC-POS System Development Information

Epos-Device API

Epos-Device XML

Server Direct Print

Setting/Checking Modes

Handling

Turning the Power On/Off

Printer Operation

Adjusting the Speaker Volume

Cleaning the Case

Cleaning the Thermal Head

Preparing for Transport

Appendix

Character Code Tables

Quick Links

Product Overview

Related Manuals for Epson TM-T70II-DT

Summary of Contents for Epson TM-T70II-DT