hit counter script
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Camcorder
  5. Vericam 35
  6. Operating manual

Panasonic Vericam 35 Operating Manual page 92

Hide thumbs
Table of Contents

Advertisement

Item
[SHOCKLESS WHITE]
[BLACK]
[ABB]
[M.PED]
[R PED]
[G PED]
[B PED]
[ABB OFFSET]
[EI]
[MODE]
[SETTING(ISO)]
[SETTING(GAIN)]
[GAIN OFFSET SW]
[OFFSET LEVEL]
[SHUTTER]
[SW]
[DISPLAY MODE]
[MODE]
[SYNCHRO deg]
[SYNCHRO sec]
[PRESET VALUE deg]
[PRESET VALUE sec]
[TEST SIG]
[TEST SIG SEL]
[COLOR BARS TYPE]
Chapter 10 Menu Operations — Menu list
Sets the transition time when switching preset values.
[OFF]: Values are immediately switched.
[1]: Switches in approximately one second.
[2]: Switches in approximately two seconds.
[3]: Switches in approximately five seconds.
f Factory setting: [OFF]
Executes automatic black balancing. When executing automatic black balancing, put the cap on the lens to
keep any light from entering the image sensor.
[EXECUTE], [CANCEL]
f Factory setting: [CANCEL]
Sets the master pedestal level.
[−100]...[100]
f Factory setting: [0]
Adjusts the Rch pedestal level.
[−100]...[100]
f Factory setting: [0]
Adjusts the Gch pedestal level.
[−100]...[100]
f Factory setting: [0]
Adjusts the Bch pedestal level.
[−100]...[100]
f Factory setting: [0]
Sets the Rch, Gch, and Bch pedestal levels after adjusting the automatic black balance.
[ON]: Maintains and adds the values of [R PED], [G PED], and [B PED] after performing the automatic
black balance.
[OFF]: Resets the values of [R PED], [G PED], and [B PED] after performing the automatic black balance.
f Factory setting: [OFF]
Switches the EXPOSURE INDEX control unit.
[ISO], [dB]
f Factory setting: [ISO]
Sets the value when [ISO] is selected.
[800], [1000], [1250], [1600], [2000], [2500], [3200], [4000], [5000], [6400], [8000], [10000], [12800]
f Factory setting: [800]
Sets the value when [dB] is selected.
[0dB], [3dB], [6dB], [9dB], [12dB], [15dB], [18dB], [21dB], [24dB]
f Factory setting: [0dB]
Sets whether to perform fine adjustment of control when [dB] is selected.
[ON], [OFF]
f Factory setting: [OFF]
Sets the fine adjustment level.
[0.0dB] - [3.0dB] (0.1 dB step)
f Factory setting: [0dB]
Enables/disables the shutter function.
[ON], [OFF]
f Factory setting: [ON]
Sets the shutter display unit.
[sec]: Displays in time.
[deg]: Displays at shutter open angle.
f Factory setting: [deg]
Switches the shutter control mode.
[PRESET]: Selects the mode from 12 modes inside the memory.
[SYNCHRO]: Selects the mode from the operable range.
f Factory setting: [PRESET]
Sets the value of angle control ([deg]).
[1.0] - [360.0]
f Factory setting: [180.0]
Sets the value of time control ([sec]). The lowest value changes depending on the frame rate ([FPS]) value.
[1/60] - [1/250]
f Factory setting: [1/48]
Selects the angle control ([deg]) value from the maximum of 12 values set in the control panel.
Preset values that can be selected in the factory setting are [11.5], [22.5], [45.0], [90.0], [120.0], [144.0],
[172.8], [180.0], [270.0], and [360.0].
f Factory setting: [180.0]
Selects the time control ([sec]) value from the maximum of 12 values set in the control panel.
Preset values that can be selected in the factory setting are [1/60], [1/100], [1/120], [1/250], [1/500],
[1/1000], and [1/2000].
f Factory setting: [1/60]
Sets the test signal output.
[OFF]: Does not output a test signal.
[BARS]: Outputs the color bar set in [COLOR BARS TYPE].
f Factory setting: [OFF]
Set the color bar to be used.
[SMPTE]: Uses the color bar in the SMPTE standard.
[FULL]: Uses full color bars.
f Factory setting: [FULL]
– 92 –
Description of settings

Advertisement

Table of Contents
loading

Related Manuals for Panasonic Vericam 35

Related Products for Panasonic Vericam 35

This manual is also suitable for:

Varicam hs

Table of Contents