Searching For Recorded Scenes (Edit Search) - JVC GY-DV5100 Instructions Manual
Dv camcorder
Hide thumbs
Also See for GY-DV5100:
- User manual (103 pages) ,
- Instructions manual (103 pages) ,
- Instructions manual (103 pages)
Table of Contents
Advertisement
REC
7.8
BATT
ALARM
8.
TALLY lamp
7. 8. 9.
VTR trigger button
7.8.
TALLY lamp
OFF
ZEBRA
SKIN
AUTO
ON
AREA
WHITE
ACCU
FOCUS
VTR
AUDIO
LEVELE CH-1
5
7. 8. 9.
VTR trigger button
CAUTION:
● The unit enters the STOP mode automatically at TAPE END. If this mode continues for 3 minutes, the mode switches to the
tape protect mode.
☞ See "LONG PAUSE TIME item on the OTHERS (1/2) menu screen" on page 86.
● If the VTR trigger button is pressed very quickly and repeatedly, or the POWER switch is moved immediately after the trigger
button is pressed, the viewfinder REC indicator lamp may blink and the GY-DV5100 may not enter the record mode. To
remedy this condition set the POWER switch to OFF and wait for 5 seconds or more before turning the power on again.
● A neat transition to the next recorded scene cannot be guaranteed if a recording is ended by turning the POWER switch or
DC power supply OFF, or by removing the battery pack.
● Trial-shooting is always recommended before recording important events to confirm the recording is satisfactory.
● The microphone may pick up the sound of the lens' iris if the iris is changed abruptly or the iris is manually moved abruptly
during recording. If the sound is found annoying, please purchase an optional microphone in order to move the microphone
away from the lens or ensure that the iris is not changed abruptly during shooting.
7. SHOOTING OPERATION
8.
To stop recording:
Press the VTR trigger button on the unit or on the lens
section again. The TALLY lamp and REC indicator lamp go
out and the unit enters the record-standby mode.
When the VTR trigger button is pressed, the unit enters the
record-standby mode after rewinding the tape for about 2
seconds (back-spacing).
9.
To restart recording:
Press the VTR trigger button on the GY-DV5100 or lens.
10.
Ending recording:
Press the VTR trigger button to enter the record-standby
mode and perform the following operations as required.
■ When it is required to unload the videocassette:
1 Slide the OPEN knob to open the cassette cover.
2 Press the EJECT button to take out the videocassette.
■ When the power should be turned off
Set the POWER switch to OFF.
When the camera is not going to be used for a long period,
detach the battery pack.
About the QUICK REC START Mode
If the VTR trigger button is pressed immediately after the
videocassette is inserted, the mode becomes the QUICK
REC START mode that enables quick start of recording.
However, when shooting starts in the middle of the tape, a
blank space appears as the new scene will not be linked
smoothly with the previous image.
Also, the time code does not continue. (Some overlap may
also occur.)
7. SHOOTING OPERATION
7-2 Searching for Recorded Scenes (Edit Search)
In the record-standby mode, it is possible to search for a scene when you want to check the recorded scene or continue recording
from the scene.
Screen indications during Edit Search
During Edit Search, the VTR mode is indicated as ED.FWD or
ED.REV on the LCD monitor or in the viewfinder. (When Status
1 screen is displayed.)
00:00:00:00
FIL1
F5.6
ED.FWD 01/02/03 AM01:23:45
ED.FWD: Forward search
ED.REV: Reverse search
55
56
EDIT SEARCH
OPEN
EDITSEARCH
MONITOR
FILTER
1
3200K
2
5600K
1 8
/
ND
.3
5600K
.4
5600K
1 64
/ ND
STATUS
SHUTTER
LCD BRIGHT
DISPLAY
MENU
AUDIO
PULL
LEVEL
OPEN
FRONT
REAR
ATUS
AUTO IRIS
FULL AUTO
BLACK
LOLUX
CH-1
CH-2
CH-1
CH-2
MODE
AUDIO IN
BACK L
STRETCH
VTR
AUDIO SELECT
NORMAL
NORMAL
CH-1
CH-2
SPOT L
COMPRESS
AUTO
CAM
MANUAL
POWER
VTR
ON
OFF
Engage the record-standby mode.
■ Searching the tape in forward direction
1.
Press the EDIT SEARCH + button. While the + button is
pressed, playback takes place at the normal speed.
2.
When the EDIT SEARCH + button is released, the standby
mode is reengaged.
20min
■ Searching the tape in reverse direction
1.
Press the EDIT SEARCH – button. While the – button is
FAS
pressed, playback takes place at -1times the normal speed.
–3dB
FAW
2.
When the EDIT SEARCH – button is released, the standby
I
SD
mode is reengaged.
B
48k
12.2V
MEMO:
● Block noise may appear and the image may freeze
during search.
EDIT SEARCH
+ button
EDIT SEARCH
– button
Advertisement
Table of Contents
