LG DLE0442W Service Manual
Electric & gas dryer
Hide thumbs
Also See for DLE0442W:
- Owner's manual (56 pages) ,
- Service manual (36 pages) ,
- Specifications (2 pages)
Related Manuals for LG DLE0442W
Summary of Contents for LG DLE0442W
- Page 1 SERVICE MANUAL CAUTION MODEL : DLE0442W DLG0452W DLE0442S DLG0452S DLE6942W DLG6952W DLE5944WM DLG5955WM DLE2544W DLG2555W...
-
Page 2: What To Do If You Smell Gas
IMPORTANT SAFETY NOTICE WARNING ! To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. RECONNECT ALL GROUNDING DEVICES WHAT TO DO IF YOU SMELL GAS: Do not try to light a match, or cigarette, or turn on Immediately call your gas supplier from a neighbor’s any gas or electrical appliance. -
Page 3: Table Of Contents
CONTENTS 1. SPECIFICATIONS ........................4 2. FEATURES AND BENEFITS ....................5 3. INSTALLATION INSTRUCTIONS ................... 6 4. COLUMBUS DRYER CYCLE PROCESS ..................9 5. COMPONENT TESTING INFORMATION ................10 6. MOTOR DIAGRAM AND SCHEMATIC..................13 7. CONTROL LAY - OUT ......................14 8. WIRING DIAGRAM ......................15 9. -
Page 4: Specifications
SPECIFICATIONS... -
Page 5: Features And Benefits
FEATURES AND BENEFITS DLE0442W/DLG0452W/DLE0442S/DLG0452S/DLE6942W/DLG6952W/DLE5944WM/ DLG5955WM DLE2544W/DLG2555W... -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS 3-1. POWER CORD 1) 4-wire connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3 wire connections. 1. 4-wire receptacle (NEMA type 14-30R) 2. 4-prong plug 3. Ground prong 4. - Page 7 2) 3-wire connection 3) Optional 3-wire connection Use where local codes permit connecting Use where local codes permit connecting cabinet-ground conductor to neutral wire. cabinet-ground conductor to neutral wire. 1. 3-wire receptacle (NEMA type 10-30R) 2. 3-wire plug 3. Neutral prong 4.
-
Page 8: Gas Requirements
3-2. Connect Gas Supply Pipe (Gas Dryer ONLY) Gas Requirements. 1 New Stainless Steel Flexible Connector - Use 4 Black Iron Pipe only if allowed by local codes (Use Design Shorter than 20’ (6.1 m) - Use 3/8” pipe A.G.A. Certified Connector) Longer than 20’... -
Page 9: Columbus Dryer Cycle Process
COLUMBUS DRYER CYCLE PROCESS Default Conditions of operation and termination Drying Cooling Wrinkle care Cycle Temp- Display erature time Electro- Temp- Default Temp- Level Time sensor Control time Control** Sense Dry * Manual Dry ** Motor Load Heater... -
Page 10: Component Testing Information
COMPONENT TESTING INFORMATION When checking the Component, be sure to turn the power off, and do voltage discharge sufficiently. CAUTION Component Test Procedure Check result Remark... - Page 11 Component Test Procedure Check result Remark...
- Page 12 Component Test Procedure Check result Remark...
-
Page 13: Motor Diagram And Schematic
MOTOR DIAGRAM AND SCHEMATIC When checking Component, be sure to turn Power off, then do voltage discharge sufficiently. NOTE Centrifugal switch Centrifugal switch (Pull Drive forward) -
Page 14: Control Lay - Out
CONTROL LAY - OUT PWB ASSEMBLY DISPLAY LAY-OUT OPTION PART MODEL P/No DISPLAY OP 1 OP 2 OP 3 OP 4 OP 5 OP 6 DLE0442W/S / DLE6942W 18:23 DLE5944WM DLG0452W/S / DLG6952W 19:23 DLG5955WM DLE2544W 18:25 19:25 DLG2555W PWB ASSEMBLY LAY-OUT... -
Page 15: Wiring Diagram
WIRING DIAGRAM ELECTRIC DRYER WIRING DIAGAM DLE5944WM GAS DRYER WIRING DIAGAM DLG5955WM... -
Page 16: Diagnostic Test
DIAGNOSTIC TEST 1. This TEST should be used for Factory test /Service test. Do not use this DIAGNOSTIC TEST other than specified. 2. Activating the Heater manually with the Door open may trip the Thermostat attached to the Heater, therefore do not activate it manually. -
Page 17: Test 1 120Vac Electrical Supply
Test 1 120VAC Electrical supply Caution Trouble Symptom Measurement Condition... -
Page 18: Test 2 Thermistor Test
Test 2 Thermistor Test --- Measure with Power Off Caution Trouble Symptom Measurement Condition Air TEMP. RES. Air TEMP. RES. Air TEMP. RES. -
Page 19: Test 3 Motor Test
Test 3 Motor test Caution Trouble Symptom Measurement Condition ”... -
Page 20: Test 4 Moisture Sensor
Test 4 Moisture sensor Caution Trouble Symptom Measurement Condition Display Value Voltage(DC) (between 6Pin terminal Remark... -
Page 21: Test 5 Door Switch Test
Test 5 Door switch test Caution Trouble Symptom Measurement Condition... -
Page 22: Test 6 Heater Switch Test - Electric Type
Test 6 Heater switch test - Electric Type Caution Trouble Symptom Measurement Condition... -
Page 23: Test 7 Gas Valve Test - Gas Type
Test 7 GAS Valve test - Gas Type Caution Trouble Symptom Measurement Condition... -
Page 24: Change Gas Setting (Natural Gas, Propane Gas)
CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS) Warning After Natural Gas Setting, applying Propane Gas Orifice or wrong use of Natural Gas Orifice will result in fire. Conversion must be made by a qualified technician. Initially STEP 1 : VALVE SETTING Full open Close STEP 2 : ORIFICE CHANGE... - Page 25 GAS VALVE FLOW START KEY PUSH “VALVE 1” ON IGNITE ON IGNITE TEMPERATURE ABOUT 370”F FRAME DETECT OPEN IGNITE OFF “VALVE 2” ON GAS IGNITION FRAME DETECT CLOSE DRYING “VALVE 2” OFF GAS IGNITION GAS VALVE STRUCTURE VALVE 1 IGNITER FRAME DETECT VALVE 2...
-
Page 26: Disassembly Instructions
DISASSEMBLY INSTRUCTIONS... -
Page 32: Exploded View
EXPLODED VIEW...