hit counter script
GE JGP633 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Cooktop
  5. JGP633
  6. Installation instructions manual
GE JGP633 Installation Instructions Manual

GE JGP633 Installation Instructions Manual

36" sealed gas cooktop
Hide thumbs Also See for JGP633:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Download this manual See also: Owner's Manual
I stallatio
I structio s
36" SealedGas Cooktop
JGP633,
JGP970,
PGP966,
ZGU36
i
Ouestions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
r_
In Canada, call 1.800.561.3344
or Visit our Website at: www.geappliances.ca
i
IN THE COMMONWEALTH
OF
MASSACH USETTS:
, This product
must be installed by a licensed
plumber
or gas fitter.
, When using ball-type gas shut-off
valves, they
shall be the T-handle type.
, A flexible gas connector,
when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions
completely
and carefully.
.IMPORTANT
- Save these
instructions
for local inspector's
use.
. IMPORTANT - Observe all g overning
codes and ordinances.
, Note to Installer-
Be sure to leave these
instructions
with the Consumer.
Note to Consumer
- Keep these instructions
for
future reference.
, Product failure due to improper
installation
is not
covered under the Warranty.
WARNING
- Thisappliancemust be
properly grounded.
.
IMPORTANT
- Leak testing of the
applianceshall be conducted accordingto the
manufacturer's
instructions.
, Proper installation
is the responsibility
of the
installer and product failure due to improper
installation
is NOT covered under warranty.
WARNING
- Disconnect
all electrical
power at the main circuit breaker or fuse box
before installing.
FOR YOUR SAFETY:
A WARNING
-
If the information
in this
manual
is not followed
exactly, a fire, explosion
or gas leak may result causing property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance!
Do not install this product with an air curtain hood
or other range hood that operates by blowing air
down on the cooktop.
This airflow may interfere
with operation
of the gas burners resulting in fire or
explosion hazard.
WHAT TO DO IF YOU SMELL
GAS:
Do not try to light any appliance.
Do not touch
any electrical
switch; do not use any phone in
your building.
Immediately
call your gas supplier from a
neighbor's
phone. Follow the gas supplier's
instructions.
, If you cannot reach your gas supplier, call the fire
department.
Installation
and service must be performed
by
a qualified
installer, service agency or the gas
supplier.
This cooktop
has been design certified
by CSA
International.
You'll find safety precautions
in your
Owner's Manual.
Read them carefully.
Installation
of this cooktop
must conform
with
local codes or, in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1/NFPA
54-Latest
edition.
, Be sure your cooktop
is installed properly by a
qualified
installer or service technician.
, To eliminate
reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-10861
(07-12 GE)
1

Advertisement

Table of Contents
loading

Related Manuals for GE JGP633

Summary of Contents for GE JGP633

  • Page 1 I structio s JGP633, JGP970, PGP966, ZGU36 In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca Ouestions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com FOR YOUR SAFETY: IN THE COMMONWEALTH A WARNING If the information in this MASSACH USETTS:...

  • Page 2: Important Safety Instructions

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS PARTS INCLUDED ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having 2 Screws 2 Hold Foam Tape amperage as noted on the rating plate.

  • Page 3: Pre-Installation

    Installation Instructions PRE-INSTALLATION CHECKLIST Remove Installation Instructions from When preparing cooktop opening, make sure the inside of the cabinet and the literature pack and read them carefully cooktop do not interfere with each other. before you begin. (See section on preparing the opening.) Be sure to place all literature, Use and Care,...

  • Page 4: Preparing The Opening

    Installation Instructions PREPARING THE OPENING MAINTAIN THE FOLLOWING RECOMMENDED GAS SUPPLY MINIMUM CLEARANCE DIMENSIONS LOCATION FROM BACKWALL 1" Min. From Backwall 13" MAX. Depth of unprotected overhead cabinets 6" MIN. clearance from cutout to side wall on the right of the unit Recommended gas supply location...

  • Page 5: Installing The Cooktop Unit

    Installation Instructions iNSTALLiNG THE COOKTOP UNiT LOCATE ELECTRICAL OUTLET AND LOCATE MOUNTING PARTS GAS SHUT-OFF VALVE BENEATH Remove the hold-down brackets from the literature CABINET package. NEVER REUSE OLD _1LS CONNECTORS WHEN I1 k' INSTALLING THIS Shut-Off UNIT. tt Outlet 12"...
  • Page 6 Installation Instructions INSTALLATION--GAS CONNECTIONS PROVIDE ADEQUATE INSTALL REGULATOR ONTO GAS SUPPLY BURNER BOX BOTTOM This cooktop is designed to operate on natural gas Screw the regulator at 4" of water column manifold pressure and 7" of onto the burner water column (W.C.) supply pressure. It is shipped box bottom pipe from the factory set for natural gas.

  • Page 7: Check For Leaks

    Installation Instructions CHECK FOR LEAKS INSTALLATION OVER BUILT-IN OVEN Before testing for leaks, make sure all burner knobs are in the OFF position. See built-in oven installation for complete installation instructions. After connecting the cooktop to gas, check system for leaks with a manometer. If a manometer is not available, turn the gas supply on to the cooktop...

  • Page 8: Extension Cords

    Installation Instructions INSTALLATION--ELECTRICAL CONNECTIONS WARNING - Disconnect allelectrical ELECTRICAL SUPPLY AND OUTLET power at the main circuit breaker or fuse box An adequate electrical supply and outlet must before installing. be used to operate the electrical parts of your cooktop. The power cord of this appliance is equipped EXTENSION CORDS...
  • Page 9 Installation Instructions USAGE SITUATIONS WHERE A CAUTION: Attachingthe adaptor ground APPLIANCE POWER CORD terminal to the wallreceptacle cover screw does not ground the applianceunlessthe screw ismetal,and WILL BE DISCONNECTED notinsulated, a nd the wallreceptacle isgrounded INFREQUENTLY through the house wiring. T he customer should have the circuit checked by a qualified electrician to make For 15 amp circuit only.

  • Page 10: Cooktop Burners

    Installation Instructions COOKTOP BURNERS Burner lake sure the pins in ASSEMBLING THE COOKTOP the burner heads BURNERS match the burner The electrode of the spark igniter is exposed. Be base indentations careful not to push any cooktop controls while the Burner head and that they are top of the burner is removed.
  • Page 11 Installation Instructions CHECK IGNITERS THE BURNER FLAMES Operation of the electric igniters should be Turn each burner on. Flames should be blue in color checked after the cooktop and supply line have with no trace of yellow. The burner flames should been carefully checked for leaks and the cooktop not flutter or blow away from the burner.

  • Page 12: Operation Checklist

    Installation Instructions OPERATION CHECKLIST When ordering parts, always include the serial Make sure all controls are left in the OFF number, model number and a code letter to position. Check to be sure the cooktop is in the ensure proper replacement parts. UNLOCKED position (on models so equipped).

  • Page 13: Making The Lp Conversion

    Butane Kit # No. 15 Torx-Head Driver JGP970 Pliers WB28TI0229 ZGU36 PGP966 WB28T10283 Small Flat-Head JGP633 WB28T10235 Screwdriver (4mm or 5/52" tip size, 60mm or Safety Glosses 2-3/8" long) ADJUST YOUR COOKTOP FOR USE SAFETY INFORMATION SHOULD KNOW WITH LP GAS...
  • Page 14 Installation Instructions MAKING THE LP CONVERSION (CONT.) CHANGE COOKTOP BURNER CHANGE COOKTOP BURNER ORIFICES ORIFICES (CONT.) Remove the top grates, On most burners, burner caps, and burner the orifices have a spring- Remove This Ring heads. loaded retaining ring around the hex head to hold the etainer Remove the spark...
  • Page 15 Installation Instructions CHANGE COOKTOP BURNER JGP633 ORIFICES (CONT.) Locate the LP orifices attached to the regulator along with separate LP conversion instructions. They will have a digit for size, and a letter for type of gas, on the top or side.
  • Page 16 Installation Instructions MAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLAMES Make the adjustment by slowly turning the screw until flame appearance is correct. Turn all burners full on and check the flames. Note: Some models may contain a silicone shield which They should be blue in color with some yellow covers the valve switch and access hole.A flashlight may tipping at the ends of the flame.
  • Page 17 I structio s Ta le de cuisson scell d'i stallati au gaz de 91 cm (36") JGP633, JGP970, PGP966, ZGU36 Web 8 I'adresse : www.electromenagersge.ca POUR VOTRE SECURITI_ AVANT DE COMMENCER AAVERTISSEMENT - Avant de commencer, lisez attentivement la totalit6 de ces instructions.
  • Page 18 Instructions d'installation INSTRUCTIONS IMPORTANTES DE SI CURITI PII_CES COMPRISES LG conception de votre table de cuisson a 6t6 approuv6 par I'ACNOR International. Vous trouverez des pr6cautions 8 prendre en mati_re de s6curit6 dans votre Guide d'utilisation et de soins. Lisez-les attentivement.
  • Page 19 Instructions d'lnstallation LISTE DE VITRIFICATION AVANT INSTALLATION Enlevez les instructions d'installation de la Pour pr6parer I'ouverture de la surface de trousse de documentation et lisez-les cuisson, vous devez vous assurer que I'int#rieur de I'armoire ne touche pas la table soigneusement avant de commencer.
  • Page 20 Instructions d'lnstallation PREPARATION DE L'OUVERTURE FT] vous DEVEZ RESPECTERLES EMPLACEMENT RECOMMANDE DEGAGEMENTS MINIMAUX SUIVANT L'ALIMENTATION DE GAZ Profondeur max de 33 cm (13") des PARTIR DU MUR ARRIERE armoires en surplomb non prot6g6es D6gagement rain. de 15 cm 16")d6coupage au 2,5 cm (i") min.

  • Page 21: De La Table De Cuisson

    Instructions d'lnstallation INSTALLATION DE LA TABLE DE CUISSON PLACEZ LA PRISE TROUVEZ LES PII_CES DE D'ALIMENTATION MONTAGE I_LECTRIQUE ET LE ROBINET Retirez les supports de fixatian de la trausse de documentatian. D'ALIMENTATION DE GAZ AU-DESSOUS DE L'ARMOIRE N'UTILISEZ JAMAIS DES j_,j RACCORDS USAGES Rodinet d'arr_t...
  • Page 22 Instructions d'installation INSTALLATION--BRANCHEMENT DU GAZ FOURNISSEZ UN BON INSTALLEZ LE RI_GULATEUR EN APPROVISIONNEMENT EN GAZ BAS DE LA BO]'TE DE BROLEURS Cette table de cuisson est conque pour fonctionner Vissez le r6gulateur dans gaz naturel 6 une pression de tubulure d'admission le raccord du bas de 4 po.
  • Page 23 Instructions d'installation F_ VI_RIFIEZ QU'IL N'Y A PAS INSTALLATION SUR UN FOUR DE FUITE ENCASTRt_ Avant de v6rifier qu'il n'y a pas de fuite, assurez- Consultez I'installation du four encastr6 pour y trouver les instructions d'installation. vous que tous les boutons de br01eurs soient en position OFF (arr_t).
  • Page 24 Instructions d'installation INSTALLATION--RACCORDS ELECTRIQUES AVERTISSEMENT - D6branchez tout ALIMENTATION I_LECTRIQUE ET PRISE courant 61ectrique au niveau du disjoncteur de la maison ou de la boTte 6 fusibles avant d'installer. Vous devez utiliser une bonne alimentation #lectrique et une bonne prise pour faire fonctionner les 616ments 61ectriques de votre table de cuisson.
  • Page 25 Instructions d'installation INSTALLATION--RACCORDS ELECTRI(:)UES {SUITE) A MISE EN GARDE : sivous fi×ez SITUATION D'UTILISATION O0 LE CORDON D'ALIMENTATION D°UN la broche de mise 6 la terre de I'adaptateur 6 une vis du couvercle de la prise murale, cela ne met pas 6 APPAREIL I_LECTROMI_NAGER EST la terre I'appareil, 6 moins que la vis soit en m#tal et INFRE_QUEMMENT DI_BRANCHI_...
  • Page 26 Instructions d'installation BRULEURS DE LA TABLE DE CUISSON Assurez-vous que les ASSEMBLEZ LES BRULEURS DE LA Capuchon de brOleur broches des t@tesde TABLE DE CUISSON brOleur L'61ectrode de I'allumeur est expos6e. Faites carrespandent attention de ne pas pousser un contr61e de la table T_te de br01eur creux de la base de de cuisson quand le haut du brOleur est enlev6.
  • Page 27 Instructions d'installation VI_RIFIEZ LES ALLUMEURS ALLUMAGE DES BRULEURS Vous devez v6rifier le fonctionnement Allumage de la table de cuisson - ©uand vous des allumeurs 61ectriques apr6s vous 6tre mettez le bouton de la table de cuisson en position soigneusement assur6 que la table de cuisson et la LITE (allumage), I'allumeur fait une s6rie d'6tincelles ligne d'approvisionnement n'ont pas de fuite et que...
  • Page 28 Instructions d'installation BRULEURS DE LA TABLE DE CUISSON {SUITE} LES FLAP1P1ESDU BROLEUR GRILLES DE BRULEUR Les trois grilles de brOleur sont conques pour leur Allumez chaque brOleur. Les flammes doivent 6tre emplacement particulier. Pour obtenir une stabilit6 bleu sans trace dejaune. Les flammes du brOleur maximum,...
  • Page 29 Instructions d'installation CONVERSION AU GAZ PROPANE (LP) RENSEIGNEMENTS RELATIFS A LA AJUSTEZ VOTRE PLAQUE DE CUISSON A UN USAGE SI_CURITI_ QUE VOUS DEVEZ CONNA/TRE AU GAZ LP Les diaphragmes du r6gulateur de pression et du D6bronchez tout le couront #lectrique, brQleur sont r6gl6s pour le gaz naturel.
  • Page 30 Instructions d'installation CONVERSION AU GAZ PROPANE (LP)(SUITE) CHANGEZ LES DIAPHRAGMES CHANGEZ LES DIAPHRAGMES BRULEURS DE LA TABLE DE BRULEURS DE LA TABLE DE CUISSON CUISSON (Suite) Enlevez les grilles du Sur la plupart des brOleurs, haut, les capuchons les diaphragmes ont une r6tention brOleur et les t6tes de...
  • Page 31 Instructions d'installation CHANGEZ LES DIAPHRAGMES JGP633 BRULEURS DE LA TABLE DE CUISSON (Suite) Rep6rez les orifices PL fix6s au r6gulateur pression et accompagn6s des instructions de conversion du gaz PL. Lo taille est indiqu@e par un chiffre et le type de gaz par une lettre, sur le dessus ou le c6t@.{Important...
  • Page 32 Instructions d'installation CONVERSION AU GAZ PROPANE (LP)(SUITE) AJUSTEZ LES FLAMMES rB-J Continuez 6 ajuster en tournant lentement visjusqu'c] ce que les flammes soient normales. DES BRULEURS Remarque : q)uelques modules sont _quip_s d'un _cran Allumez tousles brOleurs au maximum en silicone recouvrant les volants et le trou d'acc6s. v6rifiez les flammes.

This manual is also suitable for:

Pgp966Zgu36Jgp970

Table of Contents