hit counter script
GE JGP628 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Cooktop
  5. JGP628
  6. Installation instructions manual
GE JGP628 Installation Instructions Manual

GE JGP628 Installation Instructions Manual

36" sealed gas cooktop
Hide thumbs Also See for JGP628:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Download this manual See also: Owner's Manual, Technical & Service Manual
Installation
Instructions
36" SealedGas Cooktop
JGP628, JGP630, JGP963, JGP9?0,
JGP9?5, ZGU36
I
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.561.3344
or Visit our Website at: www.geappliances.ca
I
IN THE COMMONWEALTH
OF
MASSACH USETTS:
• This product must be installed by u licensed
plumber
or gas fitter.
• When using ball-type gas shut-off
valves, they
shall be the T-handle type.
• A flexible gas connector,
when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions
completely
and carefully.
•IMPORTANT
- Save these
instructions
forlocal inspector's use.
•IMPORTANT
- Observe
all
governing
codes and ordinances.
• Note to Installer-
Be sure to leave these
instructions
with the Consumer.
• Note to Consumer
- Keep these instructions
for
future reference.
• Product failure due to improper
installation
is not
covered under the Warranty.
-& WARNING
- This appliance
must be
properly grounded.
•
IMPORTANT
- Leak testing of the
applianceshall be conducted accordingto the
manufacturer'sinstructions.
• Proper installation
is the responsibility
of the installer and product failure due to
improper
installation
is NOT covered under
warranty.
-AWARNING - Disconnect
all electrical
power at the main circuit breaker
or fuse box before installing.
FOR YOUR SAFETY:
-& WARNING - If t heinformation
in this manual is not followed exactly, a fire,
explosion or gas leak may result causing property
damage, personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance!
WHAT TO DO IF YOU SMELL
GAS:
Do not try to light any appliance.
Do not touch
any electrical
switch; do not use any phone in
your building.
Immediately
call your gas supplier from a
neighbor's
phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire
department.
Installation
and service must be performed
by
a qualified
installer, service agency or the gas
supplier.
This cooktop
has been design certified
by CSA International.
You'll find safety precautions
in your Owner's Manual.
Read them carefully.
Installation
of this cooktop
must conform
with
local codes or, in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1/NFPA
54-Latest
edition.
Be sure your cooktop
is installed properly
by a
qualified
installer or service technician.
To eliminate
reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-i0612-4
(lO-lO GE)
1

Advertisement

Table of Contents
loading

Related Manuals for GE JGP628

Summary of Contents for GE JGP628

  • Page 1 JGP628, JGP630, JGP963, JGP9?0, JGP9?5, ZGU36 In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com IN THE COMMONWEALTH FOR YOUR SAFETY: MASSACH USETTS: -& WARNING - If t heinformation •...

  • Page 2: Important Safety Instructions

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS PARTS INCLUDED ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having 2 Screws 2 Hold Foam Tape amperage as noted on the rating plate.

  • Page 3: Pre-Installation

    Installation Instructions PRE-INSTALLATION CHECKLIST Remove Installation Instructions from When preparing cooktop opening, make sure the inside of the cabinet and the literature pack and read them carefully cooktop do not interfere with each other. before you begin. (See section on preparing the opening.) Be sure to place all literature, Use and Care,...

  • Page 4: Preparing The Opening

    Instollotion Instructions PREPARING THE OPENING MAINTAIN THE FOLLOWING RECOMMENDED GAS SUPPLY MINIMUM CLEARANCE LOCATION FROM BACKWALL DIMENSIONS l" Min. From Backwall 13" MAX. Depth of unprotected overhead cabinets 6" MIN. clearance from Recommended cutout to side wall on the gas supply right of the unit location From Cutout...

  • Page 5: Installing The Cooktop Unit

    Installation Instructions INSTALLING THE COOKTOP UNIT LOCATE ELECTRICAL OUTLET AND LOCATE MOUNTING PARTS GAS SHUT-OFF VALVE BENEATH Remove the hold down brackets from the CABINET literature package. NEVER REUSE OLD CONNECTORS WHEN shutoff 11 i\ INSTALLING THIS UNIT. II Outlet 12" _L Valve r_ Electrical Below...
  • Page 6 Installation Instructions INSTALLATION--GAS CONNECTIONS PROVIDE ADEQUATE INSTALL REGULATOR ONTO GAS SUPPLY BURNER BOX BOTTOM This cooktop is designed to operate on natural gas Screw the regulator at 4" of water column manifold pressure and 7" of onto water column (W.C.) supply pressure. It is shipped the burner box from the factory set for natural gas.
  • Page 7 Installation Instructions INSTALLATION OVER CHECK FOR LEAKS BUILT-IN OVEN Before testing for leaks, make sure oll burner knobs ore in the OFF position. See built-in oven installation for complete installation instructions. After connecting the cooktop to gas, check system for leaks with o manometer. If a manometer is not available, turn the gas supply on to the cooktop...
  • Page 8 Installation Instructions INSTALLATION--ELECTRICAL CONNECTIONS _AWARNING - Disconnect oil e lectricol ELECTRICAL SUPPLY AND OUTLET power ot the moin circuit breoker or fuse box An odequote electricol supply ond outlet must before instolling. be used to operote the electricol ports of your cooktop.
  • Page 9 Installation Instructions USAGE SITUATIONS WHERE -ACAUTION: Attachingthe adaptor ground APPLIANCE POWER CORD terminal to the wallreceptacle cover screw does not ground the applianceunlessthe screw ismetal,and WILL BE DISCONNECTED notinsulated, a nd the wallreceptacle isgrounded INFREQUENTLY through the house wiring. T he customer should have the circuit checked by a qualified electrician to make For 15 amp circuit only.

  • Page 10: Cooktop Burners

    Installation Instructions COOKTOP BURNERS Burner Make sure the pins in ASSEMBLING THE COOKTOP the burner heads BURNERS match the burner The electrode of the spark igniter is exposed. Be bose indentutions careful not to push any cooktop controls while the Burner heod und that they ore top of the burner is removed.
  • Page 11 Installation Instructions CHECK IGNITERS THE BURNER FLAMES Operation of the electric igniters should be Turn each burner on. Flames should be blue in color checked after the cooktop and supply line have with no trace of yellow. The burner flames should been carefully checked for leaks and the cooktop not flutter or blow away from the burner.

  • Page 12: Operation Checklist

    Installation Instructions OPERATION CHECKLIST Hake sure all controls are left in the OFF When ordering parts, always include the serial position. Check to be sure the cooktop is in the number, model number and a code letter to UNLOCKED position (on models so equipped). ensure proper replacement parts.

  • Page 13: Making The Lp Conversion

    JGP975 WB28T10231 JGP963 WB28T10233 Small Flat-Head JGP630 WB28T10235 Screwdriver (4mm or 5/32" tip size, 60mm JGP628 WB28T10236 Safety Glasses long) SAFETY INFORMATION ADJUST YOUR COOKTOP FOR USE SHOULD KNOW WITH LP GAS The pressure regulator and burner orifices (]re set...
  • Page 14 Installation Instructions MAKING THE LP CONVERSION (CONT.) CHANGE COOKTOP BURNER CHANGE COOKTOP BURNER ORIFICES ORIFICES (CONT.) Remove the top grates, NOTE: On most burners, burner cops, and burner the orifices hove o spring- Retainer emove This heads. loaded retaining ring Ground Ring the hex head to hold the Remove the spark...
  • Page 15 Installation Instructions Units with 4 burners CHANGE COOKTOP BURNER ORIFICES {CONT.) Locate the LP/Propmne orifices shipped inside the literature package. They will have a digit number and the letter "L" on the side. (Important: Save the orifices removed from the appliance for future use.) Each orifice will show a series of engraved marks, (I, II, III, X or none),...
  • Page 16 Installation Instructions MAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLAMES Make the adjustment by slowly turning the screw until flame appearance is correct. Turn all burners full on and check the flames. Note: Some models may contain a silicone shield which They should be blue in color with some yellow covers the valve switch and access hole.A flashlight may tipping at the ends of the flame.
  • Page 17 Instructions Table de cuisson scell d'installation au gaz de 91 cm (36") JGP628, JGP630, JGP963, JGP970, JGP975, ZGU36 Web 8 I'adresse ' www.electromenagersge.ca I P-1 Questions? Appelez le Centre de r_ponse 1.800.561.3344 ou visitez notre site AVANT DE COMMENCER POUR VOTRE SI_CURITI_...
  • Page 18 Instructions d'installation INSTRUCTIONS IMPORTANTES DE SI CURITI PII_CES COMPRISES La conception de votre table de cuisson a 6t6 approuv6 par I'ACNOR International. Vous trouverez des pr6cautions _] prendre en mati_re de s6curit6 dans votre Guide d'utilisation et de soins. Lisez-les attentivement.
  • Page 19 Instructions d'lnstallation LISTE DE VITRIFICATION AVANT INSTALLATION Enlevez les instructions d'installation de la Pour pr6parer I'ouverture de la surface de trousse de documentation et lisez-les cuisson, vous devez vous assurer que I'int6rieur de I'armoire ne touche pas la table soigneusement avant de commencer.
  • Page 20 Instructions d'lnstallation PREPARATION DE L°OUVERTURE VOUS DEVEZ RESPECTER LES EMPLACEMENT RECOMMA.NDE_ DE L'ALIMENTATION DE GAZ A DEGAGEMENTS MINIMAUX SUIVANT PARTIR DU MUR ARRII_RE Profondeur max de 33 cm (13") des armoires en surplomb non prot6g6es D6gagement min. de 15 2,5 cm (1") min. du mur arri_re cm (6") d6coupage au mur de c6t6 6 droite de I'appareil...

  • Page 21: Installation De La Table De Cuisson

    Instructions d'lnstallation INSTALLATION DE LA TABLE DE CUISSON PLACEZ LA PRISE TROUVEZ LES PII_CES DE MONTAGE D'ALIMENTATION I_LECTRIOUE ET LE ROBINET Retirez les supports de fixation de la trousse de documentation. D'ALIMENTATION DE GAZ AU-DESSOUS DE L'ARMOIRE N'UTILISEZ JAMAIS. DES RACCORDS USAGES Rodinet d'arr@t 11 APPARElL.
  • Page 22 Instructions d'installation INSTALLATION--BRANCHEMENT DU GAZ FOURNISSEZ UN BaN INSTALLEZ LE RI_GULATEUR EN APPROVISIONNEMENT EN GAZ BAS DE LA BO/TE DE BRULEURS Cette table de cuisson est congue pour fonctionner Vissez le r6gulateur dans gaz nuturel (_une pression de tubulure d'admission le raccord du bas de de 4 po.
  • Page 23 Instructions d'installation VI_RIFIEZ QU°IL N'Y A PAS INSTALLATION SUR UN FOUR DE FUITE ENCASTRI_ Avant de v6rifier qu'il n'y a pas de fuite, assurez- Consultez I'installation du four encastr6 pour y trouver les instructions d'installation. vous que tousles boutons de brGleurs soient en position OFF (arr#t).
  • Page 24 Instructions d'installation INSTALLATION--RACCORDS ELECTRIQUES -& AV ERTISSEM ENT - D6branchez tout ALIMENTATION I_LECTRIQUE ET PRISE courant 61ectrique au niveau du disjoncteur de la maison ou de la boTte 6 fusibles avant d'installer. Vous devez utiliser une bonne alimentation 61ectrique et une bonne prise pour faire fonctionner les 616ments 61ectriques de votre table de cuisson.
  • Page 25 Instructions d'installation INSTALLATION--RACCORDS I LECTRIQUES (SUITE) MISE EN GARDE :Sivousfi×ez SITUATION D'UTILISATION OU LE CORDON D'ALIMENTATION D'UN la broche de mise 5 la terre de I'adaptateur 5 une vis du couvercle de la prise murale, cela ne met pas 5 APPAREIL I_LECTROMI_NAGER EST la terre I'appareil, 5 mains que la vis soit en m6tal et INFRI_QUEMMENT DI_BRANCHI_...
  • Page 26 Instructions d'instollotion BROLEURS DE LA TABLE DE CUISSON Capuchon de brOleur Assurez-vous que les ASSEMBLEZ LES BROLEURS DE LA broches des t#tes de TABLE DE CUISSON brOleur L'61ectrode de I'allumeur est expos6e. Faites correspondent attention de ne pas pousser un contr61e de la table T_te de brOleur creux de la base de de cuisson quand le haut du brGleur est enlev&...
  • Page 27 Instructions d'installation VI_RIFIEZ LES ALLUMEURS ALLUMAGE DES BRULEURS Vous devez v#rifier le fonctionnement Allumage de la table de cuisson- Ouand vous des allumeurs 61ectriques upr_s vous #tre mettez le bouton de la table de cuisson en position soigneusement ussur6 que lu table de cuisson et lu LITE (allumage), I'allumeur fair une s6rie d'6tincelles ligne d'upprovisionnement n'ont pus de fuite et que...
  • Page 28 Instructions d'instollotion BROLEURS DE LA TABLE DE CUISSON (SUITE) LES FLAMMES DU BRULEUR GRILLES DE BRULEUR Les trois grilles de br01eur sont congues pour leur Allumez chaque br01eur. Les flammes doivent @tre emplacement porticulier. Pour obtenir une stabilit6 bleu sans trace dejaune. Les fiammes du br01eur maximum,...
  • Page 29 Instructions d'installation CONVERSION AU GAZ PROPANE (LP) RENSEIGNEMENTS RELATIFS .a,LA AJUSTEZ VOTRE PLAQUE DE CUISSON _, UN USAGE AU GAZ LP SI_CURITI_ QUE VOUS DEVEZ CONNATTRE D#branchez tout le courant #lectrique, niveau du disjoncteur principal ou de la boTte Les diaphragmes du r#gulateur de pression et du 5 fusibles.
  • Page 30 Instructions d'installation CONVERSION AU GAZ PROPANE (LP)(SUITE) CHANGEZ LES DIAPHRAGMES DES CHANGEZ LES DIAPHRAGMES DES BRULEURS DE LA TABLE DE BRULEURS DE LA TABLE DE CUlSSON CUISSON {SUITE) Enlevez les grilles du NOTE : Sur I(] plupart des haut, les copuchons brOleurs, les diaphragmes Bague de r6tention...
  • Page 31 Instructions d'installation Appareil avec 4 br01eurs CHANGEZ LES DIAPHRAGMES BROLEURS DE LA TABLE DE CUISSON (SUITE) Trouvez les diaphragmes de gaz LP/propane joints 5 la documentation. IIs ant un num6ro et la lettre <<L >>inscrite sur un c6t6. (Important: Conservez les diaphragmes vous avez enlev6s de votre appareil pour une utilisation future.)
  • Page 32 Instructions d'installation CONVERSION AU GAZ PROPANE (LP)(SUITE) AJUSTEZ LES FLAMMES Continuez _ ujuster en tournunt lentement visjusqu'_ ce que les flummes soient normules. DES BRULEURS Remarque : Quelques modules sont _quip_s d'un _crun Allumez tous les br_leurs au maximum en silicone recouvrunt les volunts et le trou d'ucc_s. v6rifiez les flammes.

This manual is also suitable for:

Jgp975Zgu36Jgp630Jgp963Jgp970

Table of Contents