hit counter script

Back Panel - Cisco RNG200 User Manual

High-defi nition digital-only interactive set-tops with multi-stream cablecard interface (black)
Hide thumbs Also See for RNG200:
Table of Contents

Advertisement

Back Panel

THIS DEVICE IS INTENDED TO BE ATTACHED
TO A RECEIVER THAT IS NOT USED TO
RECEIVE OVER-THE-AIR BROADCAST
SIGNALS. CONNECTION OF THIS DEVICE
IN ANY OTHER FASHION MAY CAUSE
HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS AND IS IN VIOLATION
OF THE FCC RULES, PART 15.
CATV CONVERTER
MADE IN MEXICO
1 Cable In
2 Bar Code Label
3 Video 1 (Composite)
4 Audio Out (Left/Right)
5 YPbPr
6 Out 2
(Secondary Audio Out)
7 Digital Audio Out
8 S-Video Out
9 IR
10 Optical Audio Out
11 Cable Out
12 HDMI
13 M-Card Label
14 USB 2.0
15 eSATA
16 M-Card
17 1394
18 Ethernet
19 AC Outlet
20 AC Power Input
Note: This illustration may vary from the actual product.
4
OUTPUT
DIGITAL
VIDEO
Y
AUDIO
L
Pb
R
Pr
CABLE IN
1
2
3
4
5 6
Connects to a coaxial cable that delivers the signal from your service provider
Contains set-top serial number and MAC addresses
Connects to a video input of another device, such as a TV or VCR
Connects to RCA cables that send analog audio signals (left/right) to a stereo receiver
or TV with stereo inputs
Connects to the component video input (YPbPr) on an HDTV. Do not use
these cables if you are using the HDMI connection
Connects to either a VCR or to another set of inputs (composite) on your TV
Connects to an RCA cable that sends a digital audio signal to a surround-sound receiver
or other digital audio device
Connects to S-Video input of a standard TV or VCR
Connector reserved for future use
Connects to an optical cable that sends a digital audio signal to a surround-sound
receiver or other digital audio device
Connects to a coaxial cable that sends analog audio and video signals to a TV or VCR.
These signals are SDTV video and stereo audio
Connects an HDMI
cable to the HDMI input of an HDTV. HDMI supports both digital audio
and video. May be used to connect to a DVI interface using an HDMI-to-DVI adapter for
video and separate audio connections. Any of the following audio connections may be used:
Digital Audio Out (7); Audio Out: Left, Right (4); or Optical Audio Out (10)
Contains M-Card serial number and MAC address
Connects to external USB equipment approved by your service provider, software controlled
Connects to an external Serial ATA (eSATA) hard disk drive for expanded drive space.
A connected eSATA drive is not an archival device. Support for your eSATA may vary by
service provider
Slot for M-Card module, which decrypts subscription digital channels. This set-top will not
operate correctly without an M-Card module, which is installed by your service provider
Connects to display devices that are equipped with a 1394 input
Connects to an Ethernet-equipped device (Reserved for future use)
Connects to the AC power cord from another device, such as a TV
Connects to the power cord to deliver power to the set-top
OPTICAL
MULTI-STREAM
AUDIO
OUT
MCARD SN: PXCPRPSLV
IR
L
MCARD MAC: 00 1BD73E17D9
CABLE OUT
R
USB 2.0
eSATA
S-VIDEO
OUT
7
8
9
10
11
12 13
14
15
CAUTION
CABLE CARD
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC
ELECTRIQUE NE PAS OUVRIR
120 VAC
60Hz 4.2A
500W
120VAC
60Hz 80W
1394
ETHERNET
LISTED 36MW
VIDEO PRODUCT
16
17
18
19
20
T14760

Advertisement

Table of Contents
loading

This manual is also suitable for:

Rng200n

Table of Contents