Related Manuals for Panasonic PT-LW321
Summary of Contents for Panasonic PT-LW321
- Page 1 PT-LW321 P ro d u c t N u m b e r : ™ Projector P ro d u c t N a m e : As of August 2013. Specifications and appearance are subject to change without notice.
- Page 2 PT-LW321 ™ Projector Specifications Main unit Power supply 100−240 V AC, 50/60 Hz Power consumption 245 W (0.5 W when set to , 6.0 W when STANDBY MODE set to STANDBY MODE NORMAL. DLP™ chip Panel size 16.5 mm (0.65 inches) diagonal (16:10 aspect ratio) Display method DLP™...
- Page 3 PT-LW321 ™ Projector Built-in speaker 7 × 4 cm Oval x1 output power 8 W (Monaural) Power cord length 1.8 m (5 ft 11 in) (2.0m (6 ft 7 in) for PT-LW321U) Cabinet materials Molded plastic (PC) Dimensions (W × H × D) 288 ×...
- Page 4 PT-LW321 ™ Projector Dimensions 144 (5-21/32) 73 (2-7/8) 288 (11-11/32) unit : mm (inch) NOTE: This illustration is not drawn to scale. Terminals HDMI input Monitor output MONITOR OUT COMPUTER 1 IN VIDEO IN AUDIO 2 IN AUDIO 1 IN...
-
Page 5: Standard Setting-Up Position
PT-LW321 ™ Projector Standard setting-up position unit : mm (inch) ø38 (1-1/2) Upper edge of projected image (4-14/32) (4-21/32) Screen Lower edge of projected image (8-29/32) (7-7/8) NOTE: Illustrations show the projector Screen installed using optional ceiling mount bracket ET-PKV100H and attachment ET-PKL300B. -
Page 6: Projection Distance For 16:10 Aspect Ratio Screen
PT-LW321 ™ Projector Projection distance for 16:10 aspect ratio screen unit: meters (feet) Projection size Projection distance [L] Height from the edge of screen [diagonal] Min [wide] Max [telephoto] to center of lens [ H ] 0.76 m 30˝ (3.3) (3.6) - Page 7 PT-LW321 ™ Projector Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 minimum L (m) = (diagonal screen size in inches) × 0.03338 maximum L (m) = (diagonal screen size in inches) ×...
- Page 8 PT-LW321 ™ Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Display mode Display Scanning frequency Dot clock Format resolution frequency (dots) (kHz) (Hz) (MHz) NTSC/NTSC4.43/PAL-M/PAL60 59.9 – VIDEO 720 ×...
- Page 9 PT-LW321 ™ Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below. Pin assignments and signal names...
- Page 10 PT-LW321 ™ Projector Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. C2 C3 P1 P2 ... Pn Start Colon...
-
Page 11: Status Request Commands
PT-LW321 ™ Projector Status request commands Command : Parameter Function Callback Description Main power status Standby Lamp on status Standby Lamp on control in progress Lamp on Lamp off control in progress AV mute function status Input signal status HDMI... - Page 12 PT-LW321 ™ Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. Never place objects on top of the projector while it is operating. Make sure there is the unobstructed space as shown below or more around the projector’s exhaust openings.