hit counter script
Craftsman 113.213170 Owner's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Drill
  5. 113.213170
  6. Owner's manual
Craftsman 113.213170 Owner's Manual

Craftsman 113.213170 Owner's Manual

Drill press with maximum developed 1 i/2 hp motor
Hide thumbs
Table of Contents

Advertisement

Quick Links

f
Save This Manual
"_
For Future Reference
owner's
,
manual
SP5188
MODELNO.
113.213170
DRILL PRESSWITH
MAXIMUM DEVELOPED
1 I/2 HP MOTOR
i
Serial
Number
Model and sedai number
may be found at the rear of
the head.
You should record both
model and serial number in
a safe place for future use.
i
i
i
CAUTION:
READ ALL
INSTRUCTIONS
CAREFULLY
r
CRRFTSMFIN
MOTORIZED
17-1NCH
FLOOR MODEL DRILL PRESS
• assembly
• operating
• repair parts
Sold by SEARS, ROEBUCK AND CO., Chicago,
IL 60684 U.S.A.
P_rt No. SP5188

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 113.213170

Summary of Contents for Craftsman 113.213170

  • Page 1 Save This Manual "_ For Future Reference owner's manual SP5188 MODELNO. 113.213170 DRILL PRESSWITH MAXIMUM DEVELOPED 1 I/2 HP MOTOR Serial Number Model and sedai number may be found at the rear of the head. CRRFTSMFIN You should record both model and serial number in a safe place for future use.

  • Page 2: General Safety Instructions For Power Tools

    PRESS ON CRAFTSMAN DRILL FULL ONE YEAR WARRANTY If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE...

  • Page 3: Additional Safety Instructions For Drill Presses

    additional safety instructions for drill presses £ ¢ WARNING: FOR YOUR OWN SAFETY, DO NOT To prevent the workpJece from being YOUR DRILL PRESS UNTIL IS COM- torn from your hands, spinning of the PLETELY ASSEMBLED AND INSTALLED ACCORD- tool, shattering the tool or being thrown, "_ ING TO THE INSTRUCTIONS...
  • Page 4 Think Safety. Safety _sa combination of operator Drum sanders must NEVER be operated common sense and alertness at all times when me th=s drill press at a speed greater than 1800 RPM. dNII press ,s be0ng used WARNING: Do not allow familiarity (gained from c.

  • Page 5: Table Of Contents

    glossary of terms t. Workpiece Revolution Per Minute (R.P.M.) The =ternon wh=chthe cutting operations_s being The number of turns completed by a spinning oblect in one minute performed. 2. Drill Spindle Speed S° The cuttingtoolused in the drill press to make holes The RPM of the spindle.

  • Page 6: Motor Specifications And Electrical Requirements

    motor specifications and electrical requirements MOTOR SPECIFICATIONS Thts power tool _s equipped w_lh a 3-conductor cord and grounding type plug. approved by Underwriters' Th_s drill press _s designed to use a 1725 RPM motor Lalooratones and the Canadian Standards Assoclat=on only Do not use any motor that runs faster than 1725 The ground conductor...

  • Page 7: Unpacking And Checking Contents

    unpacking and checking contents TABLE OF LOOSE PARTS WARNING: AVOID INJURY FROM UNEX- PECTED STARTING OR ELECTRICAL SHOCK, DO Item Description Qty. NOT PLUG THE POWER CORD INTO A SOURCE Table ..OF POWER. THIS CORD MUST REMAIN UNPLUG- B Column Support Asm ..GED WHENEVER YOU ARE WORKING ON THE...

  • Page 8: Table Of Loose Parts

    LLStof Loose Parts =n Box 507864 Item Description Qty. Feed Handle ..Key Drift ....C Wrench Hex "L" M3 ....Wrench Hex "L" M4 ....E Wrench Hex"L" M5 ....Crank ......Clamp-Column ....... List of Loose Parts in Bag 507865 Item Description Qty.

  • Page 9: Location And Function Of Controls

    location and function of controls 1. BELT TENSION HANDLE... Turn handle counter 9. CHUCK... Holds drdl b=tor other recommended accesso_/to perform desired operations. c!ockwfse to apply tens,on to belt. turn handle clockw,se to release belt tension. 10. BEVEL SCALE... Shows degree table is tilted BELT TENSION LOCK HANDLES...

  • Page 10: Assembly

    assembly WARNING: FOR YOUR OWN SAFETY, NEVER CON* NECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED. FRAMING SQUARE MUST BE TRUE. Check its accuracy as illustrated below. TOOLS NEEDED DRAW LIGHT STRAIGHT EDGE LINE ON BOARD BOARD 3/4"...

  • Page 11: Installing The Table

    INSTALLING THE TABLE TABLE Loosen support lock and ra=se table support 10y tumRngtable crank clockwise unbl support =s at a working height level. Tighten support lock. TABLE SUPPORT RACK TABLE SUPPORT Remove protective covering from table and dis- card. Place table in table support and tighten table lock (located under table) by hand.

  • Page 12: Mounting Motor

    1. Locate four (4) 8mm, DJa x 20ram long hex head _f,f _S_//UOTO R--- bolts, eight (8)flat _vashers, and four (4) hex nuts /" z_.,,_'// among,oose a.s..->./ 2. Install hex head bolts through motor bracket HI_X ./ ._/ ._/____ head.

  • Page 13: Installing Belt Guard Knob

    Locate center pulley assembly tn !oose parts bag and place inproper hole SPINDLE PULLEY 6. Locate two (2) V-belts in the loose parts bag. 7. Use speed chart inside belt guard to Choose speed for drilling operation. Install belts in correct position for desired speed.

  • Page 14: Motor Connections

    MOTOR CONNECTIONS WARNING: FOR YOUR OWN SAFETY, NEVER CON- NECT PLUG TO POWER SOURCE OUTLET UNTIL BLACK WIRE ALL ASSEMBLY STEPS ARE COMPLETED, TERMINAL COPPER POST t. Open motor connector box cover located on under- side of motor using a flat blade screwdriver. GREEN WIRE WARNING: TO AVOID...
  • Page 15 2. Slide the chuck up over the arbor as illustrated. "="---- SPINOLE ARBOR SUPPORT LOCK 4. Unlock support lock and raise table so its about two (2) inches below tip of chuck. 5. Turn chuck sleeve clockwise and open jaws in chuck completely.

  • Page 16: Installing Light Bulb

    INSTALLING LIGHT BULB 1. Install a light bulb (not larger than 60 watt) into the socket inside the head. ADJUSTING THE TABLE SQUARE TO HEAD NOTE: The combination square must be "true." See "Unpacking Checking Contents" section method. 1. Insert a precision ground steel rod approximately 3"...

  • Page 17: Getting To Know Your Drill Press

    getting to know your drill press FEED SPRING FEED ADJUSTMENT SPRING SPRING 4" ==,._, BELT GUARD SWITCH BELT TENSION LOCK HANDLE CHUCK BELT TENS_N LOCK HANDLE BEVEL LOCK (UNDER TABLE) BELT TENSION HANDLE SUPPORT LOCK DEPTH SCALE LOCK HEAD LOCK BEVEL SCALE DEPTH FEED HANDLE...

  • Page 18: Revel Scale

    See _nside of belt guard for specific placement of ioelts This Drill Press has 16 speeds as hsted Cerow on pulleys 200RPM 640RPM 1820RPM 290RPM 720RPM 2380RPM 350RPM 800RPM 2540RPM 430RPM 870RPM 3630RPM 500RPM 1440RPM 580RPM 1630RPM SPINDLE SPEEDS IN R.P.M. ,,,, 720' 1440...

  • Page 19: On-Off Switch

    DRILL "ON-OFF" SWITCH ... Has locking fea- ture. THIS FEATURE IS INTENDED TO HELP PREVENT UNAUTHORIZED POSSIBLE HAZARDOUS CHILDREN OTHERS, Insert KEY into swftch. NOTE: Key is made of yellow plastic. To turn drill ON ... Insert finger under switch lever and pull. To turn drill OFF...

  • Page 20: Drillingto A Specific Depth

    DRILLING TO A SPECIFIC DEPTH To drill a BLIND hole (no! all the way lhrough) to a given depth, proceed as follows. 1. Mark the deplh of lhe hole on the side of lhe work- piece. 2. Loosen the depth scale lock. 3.

  • Page 21: Removingchuck And Arbor

    OEPTH SCALE LOCK Turn the depth scale clockwise until it stops. 4, Tighten the depth scale lock, 5. The chuck will now be held at this depth when the feed handles are released, SCALE ARBOR SPINDLE HOLE LOCKING COLLAR "._ "o QUILL HOLE REMOVING...

  • Page 22: Re-Installingthe Chuck And Arbor

    RE-INSTALLING THE CHUCK AND ARBOR t. Clean thetapered surface on thearbor with a clean cloth. Make surethere are no foreignparticlesstick- ing to the surface. The slightest piece of dirt on this surface will prevent the arbor from seating properly.This will cause the drillto "wobble." 2.

  • Page 23: Basic Drill Press Operation

    basic drill press operation Never do any wQrk 'FREEHAND" (hand- Follow the following mstructlons for operating your drdl holding wor&piece rather than supportIng press tO get the best results and to m_mmize the likeli- on the tableL except when polishing. hood of personal inlury Securely lock Head and Support to Column, WARNING:...

  • Page 24: Positioning Table And Workpiece

    POSITIONING TABLE AND WORKPIECE •_= <= Lock the table to the column in a position so that the tip of the drill is just a little above the top of the work- piece. Always place a piece of BACK-UP MATERIAL (wood, plywood...) on the table underneath the workpiece.

  • Page 25: Tilting Table

    TILTING TABLE To use the table in a bevel (hired) pos_l_on, loosen the BEVEL LOCK set screw under table bevel lock wath Hex "L" wrench. Loosen bevel lock with adiustable wrench. Tilt table to desired angle by reading bevel scale. Re- tighten bevel lock and set screw.

  • Page 26: Maintenance

    maintenance WARNING YOUR SAFETY, TURN SWITCH "OFF" AND REMOVE-PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING OR LUB- RIC.a,TING YOUR DRILL PRESS. Frequently blow out any dust that may accumulate in- side the motor. A coat of automobile-type was applied to the table and column will help to keep,the surfaces clean.

  • Page 27: Trouble Shooting

    trouble shooting WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "'OFF" AND ALWAYS REMOVE PLUG FROIM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING. • CONSULT YOUR LOCAL SEARS SERVICE CENTER IF FOR ANY REASON MOTOR WILL NOT RUN. , ,,., TROUBLE PROBABLE CAUSE REMEDY 1.

  • Page 28: Repair Parts

    PARTS LIST FOR CRAFTSMAN 17" DRILL PRESS "10 MODEL NO. 113.213!70 ;:3. FIGURE...
  • Page 29 PARTS LIST FOR CRAFTSMAN 17" DRILL PRESS MODEL NO. 113.213170 Always order by Part Number--Not by Key Number FIGURE 1 PARTS LIST "O Part Description Description _11 I 81732O Knob-Motor Adjusting 817778-3 Head w/PoInter and Tr=m 817391 Screw-Socket Set 817321 Socket-Bulb Asm.
  • Page 30 PARTS LIST FOR CRAFTSMAN 17" DRILL PRESS MODEL NO. 113.213170 Always order by Part Number--Not by Key Number FIGURE Part Part Description Description 817319 817391-2 Screw-Set M8 x 1.25-8 Ring-Retaining STD315255 817331 * Bearing-Ball 25mm Pulley-Motor 817325 Knob...
  • Page 31 PARTS LIST FOR CRAFTSMAN 17" DRILL PRESS MODEL NO. 113.213170 Always order by Part Number--Not by Key Number FIGURE Part Part Description Description 817339 817309 Nut-Lock Key-Chuck 817340 Chuck 817310 Ring-Locking 817311 Washer 817341 Arbor 817326 STD315235 Key-Drift...
  • Page 32 PARTS LIST FOR CRAFTSMAN 17" DRILL PRESS MODEL NO. 113.213170 Always order by Part Number--Not by Key Number FIGURE Part Description Part Description iii i IIII 817391-1 Screw-Hex Soc Set 817361 Base M6x 1,0-10 817360 Support-Column 817286 Collar.Rack STD836040 * Screw-Hex HD M 10 x 1.5-40...
  • Page 33 NOTES...
  • Page 34 NOTES...
  • Page 35 NOTES...
  • Page 36 8EARS owner's MOTORIZED 47-1NCH manual FLOOR MODEL DRILL PRESS SERVICE Now thatyou have purchased your 17-inch Drill Press, should a need ever exist f orrepairpartsor service, s implycontact any Sears ServiceCenter and most Sears, Roebuck and Co. stores, B e sureto provide allpertinent factswhen you call or visit.

Table of Contents