Table of Contents
Advertisement
Quick Links
Hitachi Plasma TV Horizontal Wall-mount Unit
Model
PWT001
Thank you for purchasing the Hitachi Plasma TV Wall-mount Unit.
To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this
manual in a safe place for future reference.
This plasma TV wall-mount unit is for use with the following models:
HITACHI Plasma TV CL32-PD2100, CL37-PD2100, CL42-PD2100, 32PD5100, 42PD5100, 42PMA500
32PD5000, 32PD5200, 32PD5300, 37PD5200, 42PD5000, 42PD5200, 42PD5300, CMP4211/2, CMP4213/4
Special techniques are necessary for installation of the plasma TV.
I Do not attempt to perform this work by yourself.
I Request an installation specialist to install this unit.
I This company assumes absolutely no responsibility for injuries and damages that may occur due to
improper installation and handling.
I Please remember that if you remove the plasma TV set from the wall later, you will find the screw holes and
anchor bolts for the mounting unit left on the wall. Also note that a long use of the plasma TV set may
discolor the wall around it due to its heat and air flow.
To dealers and shops
G
To ensure customer safety, be sure to design the installation location so that the strength is sufficient to
withstand the weight of both the plasma TV and the wall-mount unit.
G
Always use at least two persons for all installations.
G
Fully tighten all of the mounting screws as specified in the installation instructions.
Parts Configuration Chart
Installation Instructions
Wall-mount metal
(top)
1
x
M6
TV-mount metal
x
2
x
Wall-mount metal
(center)
1
x
Wire clamp
x
Wall-mount metal
(bottom)
1
x
In the parts packing
M5 - 6 flat washer
18 screw
x
8
10
x
2
Parts for CL37-PD2100 only
M6
Bracket (R),(L)
4
x
1 each
x
18 screw
x
Advertisement
Table of Contents
Related Manuals for Hitachi PWT001
Summary of Contents for Hitachi PWT001
-
Page 1: Installation Instructions
Model PWT001 Installation Instructions Thank you for purchasing the Hitachi Plasma TV Wall-mount Unit. To ensure correct usage, please read this instruction manual thoroughly. After reading, please store this manual in a safe place for future reference. This plasma TV wall-mount unit is for use with the following models:... -
Page 2: Safety Cautions
Usage cautions to ensure correct usage Symbols GThe following symbols are used to ensure safe usage of the product, to prevent danger to yourself and other parties and to prevent damage to property. I This symbol indicates that incorrect handling due to ignoring this symbol WARNING can result in the possibility of personal injury or even death. -
Page 3: Installation Location
Installation Location WARNING Plaster board or I The wall where the wall-mount unit is to be thin ply wood, etc. installed must be capable of long-term support of the total load of the plasma TV and wall-mount unit. Measures should also be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. -
Page 4: Installation Method
CAUTION I Do not install in I Do not install where locations where there is direct there is excessive sunlight and other vibration or impact. strong light. Injury and damage Strong light could result could result from in eye fatigue during falling. - Page 5 Mounting the wall-mount unit on the wall 1. Prepare at least four sets of commercially available anchors and screws, etc., for various types of walls. 2. Carefully read the safety cautions concerning installation locations as described in this instruction manual and then select a suitable location for installation.
- Page 6 42 inch 4. Fasten the wall-mount unit securely to the wall. 5. Dressing the cables Clamp to two or more of the long slotted holes in When passing the plasma TV power cord and the upper and lower parts of each wall-mounting signal cables behind the plasma TV, use wire metal in a well-balanced manner.
- Page 7 CL37-PD2100 ➁ Fasten the bracket (R) , (L) to the TV mount metal Fasten the two TV-mount metals to the back of the with 4 M6 18 screws. plasma TV with 4 M6 18 screws. TV-mount metal 4 M6 x 18 screws 4 M6 x 18 screws Bracket Bracket...
-
Page 8: Product Specifications
Product Specifications External Dimensions Dimension (A),(B) Model CL32-PD2100 CL37-PD2100 CL42-PD2100 Mass 2.6kg Main material Steel sheet Surface treatment Black electrodeposited baked paint Angle adjustment Vertical fix Products mounted Hitachi Plasma TV CL32-PD2100 , CL37-PD2100 , CL42-PD2100... - Page 9 Fax: +46 (0) 8 562 711 13 Tel: +39 02 38073415 Servizio Clienti Email: csgswe@hitachi-eu.com Fax: +39 02 48786381/2 Email: customerservice.italy@hitachi-eu.com HITACHI EUROPE LTD (Norway) AB HITACHI EUROPE S.A.S Lyon Office STRANDVEIEN 18 B.P. 45, 69671 BRON CEDEX 1366 Lysaker...