HP D7171A - NetServer - LPr Upgrade Manual
Power supply upgrade guide
Hide thumbs
Also See for D7171A - NetServer - LPr:
- Installation manual (182 pages) ,
- User manual (126 pages) ,
- Upgrade manual (97 pages)
Related Manuals for HP D7171A - NetServer - LPr
Summary of Contents for HP D7171A - NetServer - LPr
- Page 1 HP NetServer LH 3000/3000r and LH 6000/6000r Power Supply Upgrade Guide HP Part Number 5969-2160 Printed in November 1999...
-
Page 2: Audience Assumptions
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. -
Page 3: Table Of Contents
Contents 1 Introduction ....................1 Accessory Kit Contents.................. 1 Tools and Related Documentation ..............2 Contents of This Guide .................. 2 Precautions ....................2 2 HP NetServer LH 3000: Installing a Power Supply and Fan....... 5 Remove NetServer Covers ................ 5 Install Power Supply Fan Module............... -
Page 5: Introduction
1 Introduction This guide describes how to install a power supply upgrade kit, HP Product Number D8551A, in an HP NetServer LH 3000/3000r or an HP NetServer LH 6000/LH 6000r. The power supply upgrade kit provides a redundant power supply that allows the NetServer to keep operating should one of the original power supplies fail. -
Page 6: Tools And Related Documentation
Chapter 1 Introduction Tools and Related Documentation To install a redundant power supply, you need an anti-static service kit (3M 8501/8502/8503 or equivalent). This kit includes a static-dissipating mat. The following documents describe the HP NetServer LH 3000/3000r or LH 6000/6000r: HP NetServer Installation Guide HP NetServer Online Documentation CD-ROM Contents of This Guide... - Page 7 Chapter 1 Introduction WARNING Before removing the cover, always disconnect the power cord and unplug telephone cables. Disconnect the power cord to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects, such as tools or jewelry.
-
Page 9: Hp Netserver Lh 3000: Installing A Power Supply And Fan
2 HP NetServer LH 3000/3000r: Installing a Power Supply and Fan To install a redundant power supply into an HP NetServer LH 3000/3000r, you will follow these steps: Remove NetServer covers. Install power supply fan module. Install power supply. Finish the installation. NOTE For instructions on installing a power supply and fan into an HP NetServer LH 6000/6000r, see Chapter 3. -
Page 10: Install Power Supply Fan Module
Chapter 2 HP NetServer LH 3000/3000r: Installing a Power Supply and Fan 4. From the front of the NetServer, pull the NetServer forward until you hear the locking device engage with a click. 5. Remove the top cover by loosening the thumbscrew and lifting the cover away from the NetServer. - Page 11 Chapter 2 HP NetServer LH 3000/3000r: Installing a Power Supply and Fan 4. Press the power supply fan module into the connector and swing down the hinged handle to lock the fan module into place. Open the hinge of the fan module, insert the fan, and close the hinge.
-
Page 12: Install Power Supply
Chapter 2 HP NetServer LH 3000/3000r: Installing a Power Supply and Fan Install Power Supply 1. From the back of the NetServer, loosen the thumbscrews and remove a filler panel from the power supply bay. See Figure 2-3. NOTE You can install the redundant power supply in either of the open power supply bays. - Page 13 Chapter 2 HP NetServer LH 3000/3000r: Installing a Power Supply and Fan 2. Set the new power supply module in the open bay. See Figure 2-4. CAUTION When lifting a power supply module, be prepared to support its weight. Hold the power supply module with two hands. 3.
-
Page 14: Finishing The Installation
Chapter 2 HP NetServer LH 3000/3000r: Installing a Power Supply and Fan Finishing the Installation To finish the installation, do the following: 1. Replace the covers and bezel. 2. Replace all power, telephone, and I/O cables that you disconnected earlier. 3. -
Page 15: Hp Netserver Lh 6000: Installing A Power Supply And Fan
3 HP NetServer LH 6000/6000r: Installing a Power Supply and Fan To install a redundant power supply, you will follow these steps: Remove NetServer covers. Install power supply fan module. Install power supply. Finish the installation. Remove NetServer Covers 1. Close all applications, log off all users, and power down the NetServer. 2. -
Page 16: Install Power Supply Fan Module
Chapter 3 HP NetServer LH 6000/6000r: Installing a Power Supply and Fan Install Power Supply Fan Module The redundant power supply fan module allows the NetServer to keep operating in case the original fan fails. 1. Locate the power supply fan module, and press down on the tab to unlock the hinged handle. - Page 17 Chapter 3 HP NetServer LH 6000/6000r: Installing a Power Supply and Fan Open the hinge of the fan module, insert the fan, and close the hinge. Hinged panel rotates up as you insert the fan module. Figure 3-2. Install Redundant Power Supply Fan Module 5.
-
Page 18: Install Power Supply
Chapter 3 HP NetServer LH 6000/6000r: Installing a Power Supply and Fan Install Power Supply 1. From the back of the NetServer, loosen the thumbscrews and remove the filler panel from the power supply bay. See Figure 3-3. Thumbscrews Figure 3-3. Remove Filler Panel from Power Supply Bay... - Page 19 Chapter 3 HP NetServer LH 6000/6000r: Installing a Power Supply and Fan 2. Set the new power supply module in the open bay. CAUTION When lifting a power supply module, be prepared to support its weight. Hold the power supply module with two hands. 3.
-
Page 20: Finishing The Installation
Chapter 3 HP NetServer LH 6000/6000r: Installing a Power Supply and Fan Finishing the Installation After installing the power supply and power supply fan module, do the following: 1. Replace the covers and bezel. 2. Replace all power, telephone, and I/O cables that you disconnected earlier. 3. -
Page 21: Warranty And Support
4 Warranty and Support This HP NetServer accessory is covered by a limited hardware warranty for a period of one year from receipt by the original end-user purchaser. Once installed in an HP NetServer, this accessory may carry the longer of either a one-year warranty or the remainder of the warranty period for the NetServer in which it is installed. -
Page 23: Regulatory Information
Regulatory Information For regulatory information pertaining to this HP accessory, please refer to the regulatory section of your NetServer’s Installation Guide. -
Page 25: Index
Index installing in LH 6000, 12 Precautions accessory kit contents, 1 static protection, 2 Caution regulatory information, 19 static electricity, 2 remove filler panel LH 3000, 8 LH 6000, 14 filler panel remove NetServer covers removing from LH 3000, 8 LH 3000, 5 removing from LH 6000, 14 LH 6000, 11...