hit counter script
IBM NetVista User Manual
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Desktop
  5. NetVista
  6. User manual
IBM NetVista User Manual

IBM NetVista User Manual

(english) user guide
Hide thumbs Also See for NetVista:
Table of Contents

Advertisement

Quick Links

See also: Hardware Maintenance Manual , Quick Reference Manual
™
NetVista
User Guide
Type 8301, 8302, 8303, 8304, 8305
Type 8306, 8307, 8308, 8309, 8310
Type 8311, 8312, 8313, 8314, 8315

Advertisement

Table of Contents
loading

Related Manuals for IBM NetVista

Summary of Contents for IBM NetVista

  • Page 1 ™ NetVista User Guide Type 8301, 8302, 8303, 8304, 8305 Type 8306, 8307, 8308, 8309, 8310 Type 8311, 8312, 8313, 8314, 8315...
  • Page 3 ™ NetVista User Guide Type 8301, 8302, 8303, 8304, 8305 Type 8306, 8307, 8308, 8309, 8310 Type 8311, 8312, 8313, 8314, 8315...
  • Page 4 Note Before using this information and the product it supports, be sure to read the “Safety Information” on page v and Appendix E, “Notices” on page 97. First Edition (April 2002) © Copyright International Business Machines Corporation 2002. All rights reserved. US Government Users Restricted Rights –...

  • Page 5: Table Of Contents

    Contents Safety Information ..vi Locating the connectors on the front of your computer . . 36 Lithium battery notice . . vi Locating the connectors on the rear of your Modem safety information .
  • Page 6 Setting, changing, and deleting a password . . 78 Fax Class 2 commands . 87 Using Security Profile by Device . . 78 Voice commands. . 88 Selecting a startup device. . 79 Selecting a temporary startup device . . 79 Appendix C.

  • Page 7: Safety Information

    Safety Information DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product.

  • Page 8: Lithium Battery Notice

    réseaux, aux systèmes de té lécommunication et aux modems (sauf instruction contraire mentionnée dans les procédures d’installation et de configuration). v Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent produit ou des périphériques qui lui sont raccordés, reportez-vous aux instructions ci-dessous pour connecter et déconnecter les différents cordons.

  • Page 9: Laser Compliance Statement

    v Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. v Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. v Use caution when installing or modifying telephone lines. v Avoid using a telephone (other than a cordless type) during an electrical storm.
  • Page 10 DANGER Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. DANGER: Certains modèles d’ordinateurs personnels sont équipés d’origine d’une unité de CD-ROM ou de DVD-ROM. Mais ces unités sont également vendues séparément en tant qu’options.

  • Page 11: Overview

    Overview ® Thank you for selecting an IBM computer. Your computer incorporates many of the latest advances in computer technology and can be upgraded as your needs change. This publication supports several computer models. Information in this section will help you identify your computer and help you find the chapter that contains information specific to your computer.

  • Page 12: Identifying Your Computer

    Identifying your computer See Chapter 1, “Types 8301 and 8302” on page 1. See Chapter 2, “Types 8303, 8304, and 8312” on page 9. See Chapter 3, “Types 8305, 8306, 8309, and 8313” on page 31. See Chapter 4, “Types 8307, 8308, 8310, 8311, 8314, and 8315”...

  • Page 13: Chapter 1. Types 8301 And 8302

    Chapter 1. Types 8301 and 8302 This chapter provides an introduction to the features that are available for your computer. Important Before you install or remove any option, read “Safety Information” on page v. These precautions and guidelines will help you work safely. Features This section provides an overview of the computer features and preinstalled software.
  • Page 14 System management features v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem) v Remote Administration v Automatic power-on startup...
  • Page 15 v Microsoft Windows XP Professional v Microsoft Windows 2000 Professional Operating systems (tested for compatibility) v Microsoft Windows NT ® Workstation Version 4.0 v Microsoft Windows 98 Second Edition v OS/2 ® 1. The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet.

  • Page 16: Specifications

    Specifications This section lists the physical specifications for your computer. Dimensions Heat output (approximate) in British thermal units (Btu) per hour: Height: 110 mm (4.3 in.) Minimum configuration: 257 Btu/hr (75 watts) Width: 310 mm (12.2 in.) Maximum configuration: 497 Btu/hr (145 watts) Depth: 343 mm (13.5 in.) Airflow Weight...

  • Page 17: Available Options

    Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...

  • Page 18: Installing External Options

    Installing external options This section shows the various external connectors on your computer to which you can attach external options, such as external speakers, a printer, or a scanner. For some external options, you must install additional software in addition to making the physical connection.

  • Page 19: Locating The Connectors On The Rear Of Your Computer

    Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. 1 Serial connector 8 Microphone connector 2 Mouse connector 9 USB connectors 3 Parallel connector 10 VGA monitor connector 4 Ethernet connector 11 Serial connector 5 Audio line in connector...
  • Page 20 Connector Description Serial connector Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector. Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. Parallel connector Used to attach a parallel printer, parallel scanner, or other devices that use a 25-pin parallel connector.

  • Page 21: Chapter 2. Types 8303, 8304, And 8312

    Chapter 2. Types 8303, 8304, and 8312 This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option.
  • Page 22 Connectivity v 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on ® feature v Soft modem V.90/V.44 (some models) System management features v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem) v Remote Administration...
  • Page 23 v Diskette and hard disk I/O control v Serial and parallel port I/O control v Security profile by device IBM preinstalled software Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included.

  • Page 24: Specifications

    Specifications This section lists the physical specifications for your computer. Dimensions Heat output (approximate) in British thermal units (Btu) per hour: Height: 104 mm (4.1 in.) Minimum configuration: 257 Btu/hr (75 watts) Width: 360 mm (14.2 in.) Maximum configuration: 806 Btu/hr (235 watts) Depth: 412 mm (16.2 in.) Airflow Weight...

  • Page 25: Available Options

    Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...

  • Page 26: Installing External Options

    v Limit your movement. Movement can cause static electricity to build up around you. v Always handle components carefully. Handle adapters and memory modules by the edges. Never touch any exposed circuitry. v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds.

  • Page 27: Locating The Connectors On The Rear Of Your Computer

    Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. 1 Serial connector 9 Audio line out connector 2 Mouse connector 10 Microphone connector 3 Parallel connector 11 USB connectors 4 Ethernet connector 12 VGA monitor connector...

  • Page 28: Obtaining Device Drivers

    Connector Description Serial connector Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector. Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. Parallel connector Used to attach a parallel printer, parallel scanner, or other devices that use a 25-pin parallel connector.

  • Page 29: Removing The Cover

    Removing the cover Important Read “Safety Information” on page v and “Handling static-sensitive devices” on page 13 before removing the cover. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2.

  • Page 30: Locating Components

    Locating components The following illustration will help you locate the various components in your computer. 1 Power supply 5 DIMM 2 PCI slot 6 Hard disk drive 3 AGP slot (some models) 7 CD-ROM drive or DVD-ROM drive 4 Support bar 8 Diskette drive Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit...

  • Page 31: Identifying Parts On The System Board

    The following illustration shows the locations of parts on the system board. 1 Microprocessor 9 Battery 2 DIMM connector 1 10 Clear CMOS/Recovery jumper 3 DIMM connector 2 11 SCSI LED connector 4 Power connector 12 PCI slots 5 Diskette drive connector 13 Front panel audio connector 6 Primary IDE connector 14 CD-ROM audio connector...

  • Page 32: Installing Adapters

    2. To locate the DIMM connectors. See “Identifying parts on the system board” on page 18. 3. Open the retaining clips. 4. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close.
  • Page 33 2. Pivot one of the drive bay latch handles toward the front of the computer and then pivot the drive bay cage upward, as shown, until it is latched in the up position. Repeat this procedure for the remaining drive bay. 3.
  • Page 34 4. Remove the adapter-slot-cover latch and the slot cover for the appropriate expansion slot. 5. Remove the adapter from its static-protective package. 6. Install the adapter into the appropriate slot on the system board. 7. Install the adapter-slot-cover latch. 8. Clear any cables that might impede the replacement of the drive bays. 9.

  • Page 35: Installing Internal Drives

    Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add or replace drives to your computer to increase storage capacity and to enable your computer to read other types of media such as CD-ROM.

  • Page 36: Installing A Drive

    Installing a drive To install a CD-ROM drive or DVD-ROM drive in bay 2, follow these steps: 1. Remove the cover (see “Removing the cover” on page 17). 2. If the drive you are installing is a removable-media drive, remove the bay panel from the front bezel.

  • Page 37: Installing A Rope Clip

    7. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply, and a signal cable that connects to the system board. To connect a CD-ROM drive or DVD-ROM drive to your computer, follow these steps: a.
  • Page 38 2. Use a tool, such as a screwdriver, to remove the two metal knockouts. 3. Press both sides of the air baffle and lift it outward from the computer to remove. 4. Insert the rope clip through the rear panel; then attach and tighten the nuts with an appropriately sized or adjustable wrench.

  • Page 39: Changing The Battery

    Changing the battery Your computer has a special type of memory that maintains the date, time, and settings for built-in features, such as parallel-port assignments (configuration). A battery keeps this information active when you turn off the computer. The battery normally requires no charging or maintenance throughout its life; however, no battery lasts forever.

  • Page 40: Erasing A Lost Or Forgotten Password (Clearing Cmos)

    Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwords. For more information about lost or forgotten passwords, see Access IBM on your desktop. To erase a forgotten password: 1. Turn off the computer and all attached devices. 2.
  • Page 41 3. Position the cover over the chassis and pivot it down over the computer until it snaps into place. 4. Reconnect the external cables and power cords to the computer. See “Installing external options” on page 14. 5. To update the configuration, see Chapter 5, “Using the IBM Setup Utility program”...
  • Page 42 User Guide...

  • Page 43: Chapter 3. Types 8305, 8306, 8309, And 8313

    Chapter 3. Types 8305, 8306, 8309, and 8313 This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option.
  • Page 44 Connectivity ® 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN feature System management features v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem) v Remote Administration...
  • Page 45 IBM preinstalled software Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included. Operating systems (preinstalled) (varies by model type) Note: Not all countries or regions will have these operating systems. v Microsoft ®...

  • Page 46: Specifications

    Specifications This section lists the physical specifications for your computer. Dimensions Heat output (approximate) in British thermal units (Btu) per hour: Height: 140 mm (5.5 in.) Minimum configuration: 257 Btu/hr (75 watts) Width: 425 mm (16.7 in.) Maximum configuration: 890 Btu/hr (260 watts) Depth: 414 mm (16.3 in) Airflow Weight...

  • Page 47: Available Options

    Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...

  • Page 48: Installing External Options

    v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body.

  • Page 49: Locating The Connectors On The Rear Of Your Computer

    Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer. 1 Power connector 9 Audio line out connector 2 Mouse connector 10 Microphone connector 3 Serial connector 11 USB connectors 4 Parallel connector 12 VGA monitor connector...

  • Page 50: Obtaining Device Drivers

    Connector Description Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. Serial connector Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector. Parallel connector Used to attach a parallel printer, parallel scanner, or other devices that use a 25-pin parallel connector.

  • Page 51: Removing The Cover

    Removing the cover Important: Read “Safety Information” on page v and “Handling static-sensitive devices” on page 35 before removing the cover. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2.

  • Page 52: Locating Components

    Locating components The following illustration will help you locate the various components in your computer. 1 CD drive or DVD drive 7 Battery 2 USB connector 8 DIMMs 3 USB connector 9 Microprocessor and heat sink 4 Optional drive bay 10 AGP slot (some models) 5 Hard disk drive 11 PCI slots...

  • Page 53: Identifying Parts On The System Board

    The following illustration shows the locations of parts on the system board. 1 Microprocessor 9 Battery 2 DIMM connector 1 10 Clear CMOS/Recovery jumper 3 DIMM connector 2 11 SCSI LED connector 4 Power connector 12 PCI slots 5 Diskette drive connector 13 Front panel audio connector 6 Primary IDE connector 14 CD-ROM audio connector...

  • Page 54: Installing Adapters

    2. You might have to remove an adapter to gain access to the DIMM slots. See “Installing adapters” on page 42. 3. To locate the DIMM connectors. See “Identifying parts on the system board” on page 40. 4. Open the retaining clips. 5.
  • Page 55 2. Remove the adapter-slot-cover latch and the slot cover for the appropriate expansion slot. 3. Remove the adapter from its static-protective package. 4. Install the adapter into the appropriate slot on the system board. 5. Install the adapter-slot-cover latch. What to do next: v To work with another option, go to the appropriate section.

  • Page 56: Installing Internal Drives

    Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media.

  • Page 57: Installing A Drive

    The following illustration shows the locations of the drive bays. The following list describes some of the drives that you can install in each bay and their height requirements: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) CD drive or DVD drive (preinstalled in some models) 5.25-inch hard disk drive 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.)
  • Page 58 4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Pivot the drive-bay latch handle toward the front of the computer and then pivot the drive-bay cage upward, as shown, until it is latched in the upright position.
  • Page 59 7. Install the drive into the bay. Align the screw holes and insert the two screws. 8. Pivot the drive-bay cage back into place. 9. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply and a signal cable that connects to the system board.

  • Page 60: Installing A Rope Clip

    5. If you have a CD-ROM audio cable, connect it to the drive and to the system board. See “Identifying parts on the system board” on page 40. Connecting an additional IDE CD drive or DVD drive 1. Locate the secondary IDE connector on the system board and the three-connector signal cable.

  • Page 61: Changing The Battery

    3. Insert the rope clip through the rear panel; then attach and tighten the nuts with an appropriately sized or adjustable wrench. 4. Replace the computer cover. For more information, see “Replacing the cover and connecting the cables” on page 51. 5.

  • Page 62: Erasing A Lost Or Forgotten Password (Clearing Cmos)

    5. Remove the old battery. 6. Install the new battery. 7. Replace any adapters that were removed to gain access to the battery. See “Installing adapters” on page 42 for instructions for replacing adapters. 8. Replace the cover, and plug in the power cord. See “Replacing the cover and connecting the cables”...

  • Page 63: Replacing The Cover And Connecting The Cables

    Replacing the cover and connecting the cables After working with options, you need to install any removed parts, replace the cover, and reconnect any cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the IBM Setup Utility program.
  • Page 64 User Guide...

  • Page 65: Copyright Ibm Corp

    Chapter 4. Types 8307, 8308, 8310, 8311, 8314, and 8315 This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters or drives. When installing an option, use these instructions along with the instructions that come with the option.
  • Page 66 v Accelerated graphics port (AGP) video adapter slot on the system board (some models) Audio subsystem Integrated SoundMAX 3 audio Connectivity v 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on ® feature v Soft modem V.90/V.44 (some models) System management features v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP) v Wake on LAN...
  • Page 67 v Startup sequence control v Startup without diskette drive, keyboard, or mouse v Unattended start mode v Diskette and hard disk I/O control v Serial and parallel port I/O control v Security profile by device IBM preinstalled software Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included.

  • Page 68: Specifications

    Specifications This section lists the physical specifications for your computer. Dimensions Heat output (approximate) in British thermal units (Btu) per hour: Height: 413 mm (16.25 in.) Minimum configuration: 257 Btu/hr (75 watts) Width: 191 mm (7.5 in.) Maximum configuration: 890 Btu/hr (260 watts) Depth: 406 mm (16 in.) Airflow Weight...

  • Page 69: Available Options

    Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system –...

  • Page 70: Installing External Options

    v Always handle components carefully. Handle adapters and memory modules by the edges. Never touch any exposed circuitry. v Prevent others from touching components. v When you install a new option, touch the static-protective package containing the option to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds.

  • Page 71: Locating The Connectors On The Rear Of Your Computer

    Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the back of the computer. 1 Serial connector 9 Ethernet connector 2 Mouse connector 10 Microphone connector 3 Keyboard connector 11 Audio line out connector 4 USB connectors 12 Audio line in connector 5 Serial connector...

  • Page 72: Obtaining Device Drivers

    Connector Description Serial connector Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector. Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. Keyboard connector Used to attach a keyboard that uses a standard keyboard connector.

  • Page 73: Removing The Cover

    Removing the cover Important Read “Safety Information” on page v and “Handling static-sensitive devices” on page 57 before removing the cover. To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2.

  • Page 74: Locating Components

    Locating components The following illustration will help you locate the various components in your computer. 1 Microprocessor and heat sink 4 PCI adapter 2 DIMMs 5 Power supply 3 AGP slot (some models) Moving the power supply To perform some operations inside the computer, you might need to move the power supply to access parts of the system board that are difficult to see or hard to reach.
  • Page 75 2. Push the plastic tab to release the power supply. 3. Move the power supply outward from the computer. To replace the power supply, reverse these steps. Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer.

  • Page 76: Identifying Parts On The System Board

    The following illustration shows the locations of parts on the system board. 1 Microprocessor 9 Battery 2 DIMM connector 1 10 Clear CMOS/Recovery jumper 3 DIMM connector 2 11 SCSI LED connector 4 Power connector 12 PCI slots 5 Diskette drive connector 13 Front panel audio connector 6 Primary IDE connector 14 CD-ROM audio connector...

  • Page 77: Installing Adapters

    2. You might have to remove an adapter to gain access to the DIMM slots. See “Installing adapters”. 3. To locate the DIMM connectors. See “Identifying parts on the system board” on page 63. 4. Open the retaining clips. 5. Make sure the notches in the DIMM align with the tabs on the connector. Push or insert the DIMM straight down into the connector until the retaining clips close.
  • Page 78 2. Remove the adapter-slot-cover latch and the slot cover for the appropriate expansion slot. 3. Remove the adapter from its static-protective package. 4. Install the adapter into the appropriate slot on the system board. 5. Install the adapter-slot-cover latch. User Guide...

  • Page 79: Installing Internal Drives

    What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 74. Installing internal drives This section provides information and instructions for installing and removing internal drives.

  • Page 80: Installing A Drive

    The following illustration shows the locations of the drive bays. The following list describes some of the drives you can install in each bay and their height requirements: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) CD drive or DVD drive (preinstalled in some models) 5.25-inch hard disk drive 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.)
  • Page 81 4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Make sure the drive that you are installing is set correctly as either a master or a slave device.
  • Page 82 6. Install the drive into the bay. Align the screw holes, and insert the screws that secure the drive to the bay. 7. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply and a signal cable that connects to the system board.

  • Page 83: Installing A Rope Clip

    5. If you have a CD-ROM audio cable, connect it to the drive and to the system board. See “Identifying parts on the system board” on page 63. Connecting an additional IDE CD drive or DVD drive 1. Locate the secondary IDE connector on the system board and the three-connector signal cable.
  • Page 84 2. Use a tool, such as a screwdriver, to remove the two metal knockouts. 3. Insert the rope clip through the rear panel; then attach and tighten the nuts with an appropriately sized or adjustable wrench. 4. Replace the computer cover. For more information, see “Replacing the cover and connecting the cables”...

  • Page 85: Changing The Battery

    5. Thread the cable through the rope clip and around an object that is not a part of or permanently secured to the building structure or foundation, and from which it cannot be removed; then fasten the cable ends together with a lock. What to do next v To work with another option, go to the appropriate section.

  • Page 86: Erasing A Lost Or Forgotten Password (Clearing Cmos)

    Note: When the computer is turned on for the first time after battery replacement, an error message might be displayed. This is normal after replacing the battery. 9. Turn on the computer and all attached devices. 10. Use the IBM Setup Utility program to set the date and time and any passwords.
  • Page 87 3. Position the cover on the chassis so that the rail guides on the bottom of the cover engage the rails and push the cover closed until it latches. 4. Reconnect the external cables and power cords to the computer. See “Installing external options”...
  • Page 88 User Guide...

  • Page 89: Chapter 5. Using The Ibm Setup Utility Program

    Chapter 5. Using the IBM Setup Utility program The IBM Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of your computer. The IBM Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using.

  • Page 90: User Password

    User password The user password feature deters unauthorized persons from gaining access to your computer. Administrator password Setting an administrator password deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set an administrator password. After you set an administrator password, a password prompt is displayed each time you try to access the IBM Setup Utility program.

  • Page 91: Selecting A Startup Device

    Selecting a startup device If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device. Selecting a temporary startup device Use this procedure to startup from any boot device.
  • Page 92 User Guide...

  • Page 93: Appendix A. Updating System Programs

    1. From your browser, type http://www.pc.ibm.com/support in the address field and press Enter. 2. Click NetVista and NetVista Thin Client. 3. Click NetVista Personal Computer. 4. Click Downloadable files. 5. Under Select your product, choose your machine type and click Go.

  • Page 94: Recovering From A Post/Bios Update Failure

    9. Print these instructions. This is very important since they are not on the screen after the download begins. 10. From your browser, Click Back to return to the list of files. Carefully follow the printed instructions to download, extract, and install the update. Recovering from a POST/BIOS update failure If power to your computer is interrupted while POST/BIOS is being updated (flash update), your computer might not restart correctly.

  • Page 95: Appendix B. Manual Modem Commands

    Appendix B. Manual modem commands The following section lists commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection.
  • Page 96 Command Function Force modem off-hook (make busy) Note: H1 command is not supported for Italy Display product-identification code Factory ROM checksum test Internal memory test Firmware ID Reserved ID Low speaker volume Low speaker volume Medium speaker volume High speaker volume Internal speaker off Internal speaker on until carrier detected Internal speaker always on...

  • Page 97: Extended At Commands

    Extended AT commands Command Function &C_ &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 &D_ Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle...

  • Page 98: Mnp/V.42/V.42Bis/V.44 Commands

    Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 Disable auto-retrain Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11,...

  • Page 99: Fax Class 1 Commands

    Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing Receive data +FRM=n +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class.

  • Page 100: Voice Commands

    +FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID. Voice commands Select Baud Rate #BDR #CID Enable Caller ID detection and reporting format #CLS Select Data, Fax or Voice/Audio #MDL?
  • Page 101 Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix B.
  • Page 102 User Guide...

  • Page 103: Appendix C. System Address Maps

    Appendix C. System address maps The following charts represent how the hard disk stores different types of information. Address ranges and byte sizes are approximate. System memory map The first 640 KB of system board RAM is mapped starting at address hex 00000000. A 256-byte area and a 1 KB area of this RAM are reserved for BIOS data.
  • Page 104 Table 2. I/O address map (continued) Address range (hex) Size (bytes) Description 0070, bits 6:0 6 bits Real-time clock, address 0071 Real-time clock, data 0072 1 bit Enable NMI 0072, bits 6:0 6 bits RTC address 0073 RTC data 0080 POST checkpoint register during POST only 008F Refresh page register...

  • Page 105: Dma I/O Address Map

    Table 2. I/O address map (continued) Address range (hex) Size (bytes) Description 03F0 – 03F5 Diskette channel 1 03F6 Primary IDE channel command port 03F7 (Write) Diskette channel 1 command 03F7, bit 7 1 bit Diskette disk change channel 03F7, bits 6:0 7 bits Primary IDE channel status port 03F8 –...
  • Page 106 Table 3. DMA I/O address map (continued) Address (hex) Description Bits Byte pointer 0083 Channel 1, page table address register 00 – 07 0087 Channel 0, page table address register 00 – 07 0089 Channel 6, page table address register 00 –...

  • Page 107: Appendix D. Interrupt Request And Direct Memory Access Channel Assignments

    Appendix D. Interrupt request and direct memory access channel assignments The following tables list the IRQ and DMA channel assignments. Table 4. IRQ channel assignment System resource Critical system error System-management interrupt for power management Timer Keyboard Cascade interrupt from slave PIC COM2 (some models only) COM1 Available to user...
  • Page 108 User Guide...

  • Page 109: Appendix E. Notices

    Appendix E. Notices IBM may not offer the products, services, or features discussed in this document in all countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.

  • Page 110: Trademarks

    Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both: NetVista Wake on LAN PS/2 OS/2 Intel, Pentium, NetBurst, and Extreme are trademarks of Intel Corporation in the United States, other countries, or both.
  • Page 111 1.8GHz 2.0GHz 2.26GHz 2.4GHz Energy consumption efficiency value = 0.00086 0.00077 0.00068 0.00064 Types 8305 and 8306 1.8GHz 2.0GHz 2.26GHz 2.4GHz Normal Power consumption (W) 59 [W] 58 [W] 61 [W] 64 [W] Maximum power consumption(W, VA) 172 [W]/ 152 [W]/ 160 [W]/ 167 [W]/ 219 [VA]...
  • Page 112 Types 8310 and 8311 1.8GHz 1.9GHz 2.0GHz 2.26GHz 2.4GHz Normal Power consumption (W) 59 [W] 61 [W] 58 [W] 61 [W] 64 [W] Maximum power consumption(W, 180 [W]/ 184 [W]/ 160 [W]/ 169 [W]/ 174 [W]/ 232 [VA] 236 [VA] 204 [VA] 213 [VA] 220 [VA]...

  • Page 113: Index

    Index drives (continued) hard disk 5, 13, 35, 57 adapters installing 24, 45, 68 accelerated graphics port (AGP) 13, 35, 57 internal 1, 9, 23, 31, 44, 53, 67 installing removable media 13, 35, 57 Types 8303, 8304, and 8312 20 specifications 23, 44, 67 Types 8305, 8306, 8309, and 8313 42 Types 8307, 8308, 8310, 8311, 8314, and 8315 65...
  • Page 114 modem Basic AT commands 83 USB connectors 8, 16, 38, 60 Extended AT commands 85 using, security profile by device 78 Fax Class 1 commands 87 Fax Class 2 commands 87 MNP/V.42/V.42bis/V.44 commands 86 Voice commands 88 mouse connector 8, 16, 38, 60 video, subsystem 1, 9, 31, 53 moving the power supply 62 noise level 4, 12, 34, 56...
  • Page 116 Part Number: 49P0935 Printed in U.S.A. (1P) P/N: 49P0935...

This manual is also suitable for:

831542u - netvista a30 - 8315Netvista 8301Netvista 8306Netvista 8302Netvista 8307Netvista 8303 ... Show all

Table of Contents