Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Related Manuals for Panasonic AY-EB500
Summary of Contents for Panasonic AY-EB500
- Page 1 Nonlinear Editing System Hard Disk Box AY-EB500 Before attempting to connect or operate this product, please read these instructions completely...
-
Page 2: Table Of Contents
CONTENTS PREFACE .................................... 1 PRECAUTIONS ................................... 1 MAJOR OPERATING CONTROLS AND THEIR FUNCTION ....................2 INITIAL SETTING ................................3 INSTALLATION ................................... 4 CONNECTION ..................................8 SPECIFICATIONS ................................9 STANDARD ACCESSORIES ............................... 9 CAUTION For U.S.A Warning: RISK OF ELECTRIC SHOCK DO NOT OPEN This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in... -
Page 3: Preface
The AY-EB500 Nonlinear Editing System Hard Disk Box Up to five AY-EB500 Hard Disk Boxes can be connected is especially designed for use with the Nonlinear Editing to the Editing System using optional Panasonic SCSI System. cables. The Hard Disk Box accepts and supplies power to up to two 3.5”... -
Page 4: Major Operating Controls And Their Function
MAJOR OPERATING CONTROLS AND THEIR FUNCTION FRONT PANEL POWER A Y - E B 5 0 0 REAR PANEL SCSI ID 3210 3210 ~AC IN Caution 1. Power Button/Power Indicator (POWER)(Red) • Switching Power Off Press this button to turn on the power. The Power Before switching power off, terminate all the soft- Indicator lights red while the power is on. -
Page 5: Initial Setting
3. SCSI ID Setup Switch for Channel A 7. SCSI Output Connector for Channel B (chB/OUT) (SCSI ID, chA) Connect the “chB/IN” terminal of an additional HDD- The SCSI-ID for Channel A is set with this switch. BOX to this connector. Refer to page 8 for ID Number Setting. -
Page 6: Installation
INSTALLATION Installation to HDD-BOX q Disconnect the power cord of the HDD-BOX from the Warning AC outlet receptacle. Do not touch the power unit (indicated below w Remove 7 screws from the HDD-BOX. with hands, metal or other objects. Otherwise, there is a danger of electric shock. - Page 7 y Fasten the HDD securely in the position shown Wiring below with two mounting screws (provided). Note: Securely connect cables and wires to the correct terminals referring to the drawings below. Make sure Mounting Screws not to reverse connectors. (supplied) q Connect the cables from the LED PCB (eorange and rgray) to HDD left.
- Page 8 t Connect the SCSI ID setup cable (pin q: red) to HDD left. y Connect the SCSI ID setup cable (pin q: brown) to HDD right. HDD (left) HDD (right) SCSI CABLE SCSI CABLE ch A ch A u Connect a flat cable to HDD left. i Connect a flat cable to HDD right.
- Page 9 o Lower the top cover onto the HDD-BOX (o-1) and If LED fails to light: slide it in direction (o-2). Take the following steps to make sure that each cable is properly connected. • Press the power switch off and pull out the power plug from the electrical outlet.
-
Page 10: Connection
CONNECTION Connection of HDD-BOX and SCSI SCSI ID Setting Board • Set the SCSI-ID Setup Switch located on the rear of the HDD-BOX as shown in the table below. • Connection of one HDD-BOX Connect the SCSI connector (OUT) of the SCSI board and the SCSI connector (IN) of the HDD-BOX. -
Page 11: Specifications
SPECIFICATIONS Power Supply : 120V AC 60Hz Power Consumption : WIDE SCSI Input : WIDE SCSI Output : x2 (Loop through output) HDD dimensions : 3.5” (102 (W) x 152 (D) x MAX. 42 (H) mm) Installable HDD Units : max. - Page 12 Broadcast & Television Systems Company Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3F-5, Secaucus, NJ 07094 Regional Offices: EASTERN ZONE: 43 Hartz Way, Secaucus, NJ 07094 (201) 348-7620 CENTRAL ZONE: 1707 North Randall Road, Elgin, IL 60123 (708) 468-5200...