Advertisement
Quick Links
Advertisement
Related Manuals for DeWalt DCMPS520P1-QW
Summary of Contents for DeWalt DCMPS520P1-QW
- Page 1 DCMPS520...
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A XXXX XX XX Fig. B...
- Page 4 Fig. C Fig. D Fig. E Fig. F 1/8" (3 mm) Fig. G Fig. H...
- Page 5 Fig. I Fig. J Fig. L Fig. K 60° Fig. M Fig. N 0.025" (0.635 mm)
- Page 6 English 18V PRUNER SAW DCMPS520 Congratulations! EC‑Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data Pruner Saw DCMPS520 DCMPS520...
- Page 7 English Batteries Chargers/Charge Times (Minutes)*** DCB112/ DCB115/ Weight (kg) DCB104 DCB107 DCB113 DCB116 DCB117 DCB118 DCB132 DCB119 Cat # DCB1102 DCB1104 DCB546 18/54 6.0/2.0 1.08 DCB547 18/54 9.0/3.0 1.46 135* 110* 135* DCB548 18/54 12.0/4.0 1.46 DCB181 0.35 DCB182 0.61 60/40** 60/45** 60/40** 60/40** DCB183...
- Page 8 English GENERAL POWER TOOL SAFETY WARNINGS c ) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power WARNING: Read all safety warnings, instructions, source and/or battery pack, picking up or carrying illustrations and specifications provided with this the tool.
- Page 9 English h ) Keep handles and grasping surfaces dry, clean and Saw chains contacting a "live" wire may make exposed free from oil and grease. Slippery handles and grasping metal parts of the pruner "live" and could give the operator surfaces do not allow for safe handling and control of the an electric shock.
- Page 10 English q ) This pruner is not intended for tree felling. Use of the 8 . Never let the moving saw chain contact any object at the tip of the guide bar. pruner for operations different than intended could result 9 . Keep the working area free from obstructions such in serious injury to the operator or bystander.
- Page 11 English Saw Chain ‑ A loop of chain having cutting teeth, that cut the • Do not cut vines and/or small under‑brush. • wood, and that is driven by the motor and is supported by the • Use extreme caution when cutting small size brush and guide bar.
- Page 12 English Important Safety Instructions for All reassembly may result in a risk of electric shock, electrocution Battery Chargers or fire. • In case of damaged power supply cord, the supply cord must sAVE ThEsE insTRUCTiOns: This manual contains important be replaced immediately by the manufacturer, its service agent safety and operating instructions for compatible battery or similar qualified person to prevent any hazard.
- Page 13 English READ ALL INSTRUCTIONS If the charger indicates a problem, take the charger and battery pack to be tested at an authorised service centre. Do not charge or use battery in explosive atmospheres, • such as in the presence of flammable liquids, gases or hot/Cold Pack Delay dust.
- Page 14 English terminals are protected and well insulated from 3 batteries of 36 Wh each. The Use Wh rating might indicate 108 Wh (1 battery implied). materials that could contact them and cause a short circuit. NOTE: Lithium‑ion batteries should not be put in Storage Recommendations checked baggage.
- Page 15 English Battery Type The following tools operate on an 18-volt battery pack: Always use two hands when operating DCMPS520. the pruning saw. These battery packs may be used: DCB181, DCB182, DCB183, DCB184, DCB184B, DCB187, DCB189, DCB546, DCB547, DCB548, DCBP034, DCBP034G. Refer to Technical Data for Switch the tool off.
- Page 16 English ASSEMBLY AND ADJUSTMENTS 5. Ensure the saw chain is properly set in the slot around the entire guide bar. WARNING: To reduce the risk of serious personal 6. Place the saw chain around the sprocket 22 while lining up injury, turn tool off and disconnect battery pack the slot on the guide bar with chain tensioning pin ...
- Page 17 English 1. Place the saw on a flat, firm surface. guide Bar Cover as described in Installing 2. Remove chain assembly cover 7 1. To open the guide bar cover 12 , lift up on the latch the Guide Bar and Saw Chain section. pull the two halves apart.
- Page 18 English Operating the Pruner (Fig. A) nOTE: If too much force is applied while making a cut the pruner will turn off. To restart pruner, you must release the WARNING: Read and understand all instructions. Failure lock-off lever 2 and the trigger switch 1 ...
- Page 19 English installing attachments or accessories. An accidental 5. When the tree is supported along its entire length, make a cut from the top (overbuck), but avoid cutting the earth as start‑up can cause injury. this will dull your pruner quickly. The charger and battery pack are not serviceable. CUT FROM TOP (OVERBUCK) Lubrication AVOID CUTTING EARTH...
- Page 20 English 7. Install the chain, guide bar and chain assembly cover 7 Protecting the Environment as described in Installing the Guide Bar and Saw Chain, Separate collection. Products and batteries marked Replacing the Saw Chain sections and adjust chain tension with this symbol must not be disposed of with normal properly before use as described in the Adjusting Chain household waste.
- Page 21 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg enduser.BE@SBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark www.dewalt.dk WALT (Stanley Black&Decker AS)