Mitsubishi Electric FR-E720-008 Instruction Manual page 290
Hide thumbs
Also See for FR-E720-008:
- Installation manualline (43 pages) ,
- Instruction manual (312 pages)
Table of Contents
Advertisement
Causes and corrective actions
Operation panel
E.THM
indication
Motor overload trip (electronic thermal relay function) ∗1
Name
The electronic thermal relay function in the inverter detects motor overheat due to overload or reduced cooling
capability during constant-speed operation and pre-alarm (TH display) is output when the integrated value reaches
85% of the Pr. 9 Electronic thermal O/L relay setting and the protection circuit is activated to stop the inverter output
Description
when the integrated value reaches the specified value. When running a special motor such as a multi-pole motor or
multiple motors, provide a thermal relay on the inverter output side since such motor(s) cannot be protected by the
electronic thermal relay function.
Check the motor for use under overload.
Check point
Check that the setting of Pr. 71 Applied motor for motor selection is correct. (Refer to page 117).
Check that stall prevention operation setting is correct.
Reduce the load weight.
Corrective action
For a constant-torque motor, set the constant-torque motor in Pr. 71 Applied motor.
Check that stall prevention operation setting is correct. (Refer to page 91).
∗1
Resetting the inverter initializes the internal thermal integrated data of the electronic thermal relay function.
Operation panel
E.FIN
indication
Name
Heatsink overheat
If the heatsink overheats, the temperature sensor is actuated and the inverter trips.
The FIN signal can be output when the temperature becomes approximately 85% of the heatsink overheat protection
Description
operation temperature. For the terminal used for the FIN signal output, assign the function by setting "26 (positive
logic) or 126 (negative logic)" in any of Pr. 190 to Pr. 192 (output terminal function selection). (Refer to page 144).
Check for too high surrounding air temperature.
Check for heatsink clogging.
Check point
Check that the cooling fan is not stopped (Check that
Set the surrounding air temperature to within the specifications.
Corrective action
Clean the heatsink.
Replace the cooling fan.
Operation panel
E.ILF
indication
Input phase loss ∗
Name
Inverter trips when function valid setting (=1) is selected in Pr. 872 Input phase loss protection selection and one phase of
Description
the three phase power input is lost. (Refer to page 171).
It may be available if phase-to-phase voltage of the three-phase power input becomes largely unbalanced.
Check for a break in the cable for the three-phase power supply input.
Check point
Check that phase-to-phase voltage of the three-phase power input is not largely unbalanced.
Wire the cables properly.
Repair a break portion in the cable.
Corrective action
Check the Pr. 872 Input phase loss protection selection setting.
Set Pr. 872 = "0" (without input phase loss protection) when three-phase input voltage is largely unbalanced.
∗ Available only for three-phase power input model.
Operation panel
E.OLT
indication
Name
Stall prevention stop
If the output frequency has fallen to 1Hz by stall prevention operation and remains for 3s, a fault (E.OLT) appears and
Description
trips the inverter. OL appears while stall prevention is being activated.
E.OLT may not occur if stall prevention (OL) is activated during output phase loss.
Check point
Check the motor for use under overload. (Refer to page 92).
Corrective action
Reduce the load weight. (Check the Pr. 22 Stall prevention operation level setting.)
290
FR-PU04
Motor Ovrload
FR-PU07
FR-PU04
H/Sink O/Temp
FR-PU07
is not displayed on the operation panel).
FR-PU04
Fault 14
FR-PU07
Input phase loss
FR-PU04
Stll Prev STP (OL shown during stall prevention operation)
FR-PU07
Hide quick links:
Advertisement
Table of Contents
