Advertisement
Quick Links
Speed Limiter Kit
Sand Pro
Model No. 08720
This product complies with all relevant European
directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
WARNING
CALIFORNIA
Proposition 65 Warning
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
2040Z Traction Unit
Description
Lift bracket (left-hand)
Lift bracket (right-hand)
Locknut (1/2 inch)
Cable
Cam bracket (left-hand)
Cam bracket (right-hand)
Cam
Socket-head cap screw
Jam nut
Flange bushing
Spacer (3/8 x 17/32 inch)
Bolt (3/8 x 1-1/4 inch)
Fender washer (3/8 inch)
Locknut (3/8 inch)
Bolt (5/16 x 3/4 inch)
Flange nut (5/16 inch)
Cam spring
Cable tie
Bolt (5/16 x 3-1/2 inch)
Friction washer
Spacer (5/16 x 3/8 inch)
Spacer (5/16 x 1 inch)
Flange nut (5/16 inch)
Register at www.Toro.com.
Safety
WARNING
If you drive the machine without an attachment
installed, it can tip over and injure someone
or damage property.
Do not drive the machine without a
Toro-approved attachment installed.
Qty.
1
1
Install the lift brackets.
2
2
1
Install the cables onto the cam brackets.
1
2
2
2
2
Install the cams.
2
2
4
2
4
4
Install the cam brackets.
2
2
2
4
Route and mount the cables.
2
2
2
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3457-791 Rev A
Installation Instructions
Use
*3457-791*
Advertisement
Related Manuals for Toro 08720
Summary of Contents for Toro 08720
- Page 1 Form No. 3457-791 Rev A Speed Limiter Kit Sand Pro ® 2040Z Traction Unit Model No. 08720 Installation Instructions Safety This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
- Page 2 Procedure Description Qty. Check the operation of the attachment – No parts required lift. – No parts required Adjust the speed and the tracking. – No parts required Install the stop plates. Installing the Lift Brackets Parts needed for this procedure: Lift bracket (left-hand) Lift bracket (right-hand) Locknut (1/2 inch)
- Page 3 Installing the Cables onto Installing the Cams the Cam Brackets Parts needed for this procedure: Parts needed for this procedure: Socket-head cap screw Cable Jam nut Cam bracket (left-hand) Flange bushing Cam bracket (right-hand) Spacer (3/8 x 17/32 inch) Bolt (3/8 x 1-1/4 inch) Procedure Fender washer (3/8 inch) Remove the jam nut nearest the visible internal...
- Page 4 g024658 Figure 6 g024657 Figure 8 1. Cam 3. Flange bushing 2. Spacer (3/8 x 17/32 inch) 1. Locknut (3/8 inch) 3. Bolt (3/8 x 1-1/4 inch) 2. Fender washer (3/8 inch) 4. Cam Use tape or a marker to mark the exact locations of the stop plates (Figure Secure the cam with a 3/8 x 1-1/4 inch bolt, 2...
- Page 5 g024656 Figure 9 g024718 1. Bolts (5/16 x 3/4 inch) 3. Flange nuts (5/16 inch) Figure 11 2. Cam bracket 1. Tab 3. Slot 2. Spring Secure the bracket with 2 bolts (5/16 x 3/4 inch) and 2 flange nuts (5/16 inch). Hook the other end of the spring over the tab on Rotate each cam toward the center of the the cam bracket...
- Page 6 g024654 Figure 14 g024664 Figure 12 1. Cable tie 3. Cable Some parts shown as transparent 2. Control-lever damper 4. Hole 1. Cable (left-hand side shown) Use a cable tie to secure each cable to the control-lever damper on each side (Figure 14).
- Page 7 Assemble the spring at the end of each cable onto a 5/16 x 3-1/2 inch bolt, with a short spacer, a long spacer, and 2 friction washers as shown Figure Adjusting the Speed and the Tracking No Parts Required Adjusting the Speed Loosen the jam nut on the socket-head cap screw on each cam (Figure...
-
Page 8: Operation
Operation • Tighten the cap screw to increase the speed. • Loosen the cap screw to decrease the speed. Using the Speed Limiter Kit Tighten the jam nuts to secure the socket-head cap screws. If you lower the attachment while driving over a certain Repeat steps through as necessary. - Page 9 Notes:...
- Page 10 Notes:...
- Page 11 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 12 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.