Samsung SWA-9200S - Wireless Speaker Manual

Also See for SWA-9200S:

Table of Contents

CHECKING THE COMPONENTS

Surround Speaker X 2 / Speaker Cable / AC/DC Adapter / Power Cord

NOTE

For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Rear of the Main Unit)
Design and specifications are subject to change without prior notice.

Connect the Surround speaker cables
Use the speaker cables to connect the two surround sound speakers.

When connecting the speaker cable, connect the core wire to the speaker.
Insert the wire fully, taking care not to insert beyond the wire insulation.
When connecting the speaker cables to the surround speakers, follow these steps:
- Insert the red and black colored ends of each speaker cable into the red and black jacks of the appropriate speaker.
- The labels are on the backs of the speakers.
- The length of the speaker audio cable: 6 m

Turn on the Surround speakers
Plug the Surround speakers' power cord into an electrical outlet to turn on the Surround speakers. The LINK LED indicator(blue LED) on the rear of left surround speaker will blink quickly.
If the LINK LED does not blink, please see step 6.
Turn off the Soundbar
If the Soundbar is turned on, please turn off the Soundbar by pressing the (Power) button on the Soundbar or remote control.

The image of the Soundbar may differ from your Soundbar, depending on the model.

Connect Soundbar and Surround Speakers
Press the Up button on the remote control for more than 5 seconds until the "ID SET" message appears on the Soundbar's display. The message will disappear shortly.
(If your Soundbar does not have a display window and only LED indicators, please refer to the LED information below.)

After the ID SET process is successful, the Soundbar will turn on automatically.
The image of the Soundbar may differ from your Soundbar, depending on the model.

Check the connection complete
The LINK LED stops blinking and changes to solid blue when the Soundbar and surround speakers are successfully linked.
Please turn off the Soundbar and turn it back on. Confirm that the LINK LED is blue.
(It may take a minute depending on the environment.)

If the LINK LED does not turn to solid blue in a minute, please repeat from step 2 through 5 referring to step 6
(LED indicator's status).

LINK (Blue) On : Connected with the Soundbar.

LINK (Blue) Blinking fast (at an interval of around 0.5 second) : Surround speakers are in ID SET mode.

LINK (Blue) Blinking slow (at an interval of around 1 second) : Previously connected to a Soundbar but cannot currently find it.

Press the ID SET button on the rear of the left surround for more than 5 seconds until the LINK LED starts blinking fast in blue.
Repeat steps 3 through 5.

STANDBY (Red) On : When the Soundbar turns off or connection has failed.

Follow the instructions for "Link (Blue) Blinking slow (at an interval of around 1 second)" above.

Others : Errors

If the Surround speakers are successfully paired and connected to a Soundbar, the LINK LED indicator on the rear of the Left Surround is on and solid blue. Please reconnect the Surround speakers to your Soundbar referring to 02-6, LED Indicator's status.
Other devices sending radio frequency signals in proximity may interrupt the connection. Please keep your speaker away from such devices.
The content you are playing may have no surround track but only stereo. Please change the sound mode to Surround by pressing SOUND MODE button on the remote control.

There is sound jitter, delays, noise or dropout from the sound of Surround Speakers.

There may be sound jitter or delays when the Surround Speakers are far from the Soundbar. Please place them near the Soundbar.
There may be sound jitter or delays when the Soundbar is near an electrical device that can cause radio interference. Please place the Soundbar far from such devices that can cause radio interference (e.g. wireless router).
Please change the TV network connection status from wireless to wired.

Please increase the rear level referring to the manual of your Soundbar.
(You can download the manual of your Soundbar from www.samsung.com/support)

Be sure the wall is stable. If the wall is weak, reinforce it before installation.
Take care not to install the speakers sideways or upside down.
Samsung Electronics is not liable for any damage to the product due to improper installation.
Wall mounts aren't sold by Samsung Electronics.

Compatible with select Samsung Soundbar. Please visit the Soundbar product page at www.samsung.com/support for more information.
Compatible model list is subject to change without further notice.

To send inquiries and requests for questions regarding open sources, contact Samsung Open Source
(http://opensource.samsung.com)

Subwoofer Name SWA-9200S (LEFT/RIGHT)
Weight 1.7 kg	Dimensions (W x H x D) 105.0 x 152.8 x 109.0 mm
Operating Temperature Range 10 ℃ to 40 ℃	Operating Humidity Range 10% ~ 80%, non-condensing
AMPLIFIER Rated Output power 60 W x 2