SONY ICF-M1000 - FM/AM PLL Synthesized Radio Manual

Also See for ICF-M1000:

Service manual (44 pages)

Operating instructions (2 pages)

Specifications (2 pages)

Table of Contents

Contents

1 Overview
2 Features
3 Setting the clock
4 Operating the radio
5 Improving the reception
6 Connecting external equipment
7 Precautions
8 Specifications
9 Documents / Resources
- 9.1 References
- 9.2 Download manual

SONY ICF-M1000 - FM/AM PLL Synthesized Radio Manual

Overview

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
To reduce the risk of fire or electric shock, do not place objects filled with liquids, such as vases, on the apparatus. Connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately.

Features

High-fidelity FM/AM PLL (phase locked loop) synthesized table radio.
Prismatic LCD display for table top use.
Digital tuning control knob permits easy accurate tuning.
Tone control.
Furniture-grade, hand-lacquered high gloss surface.
Wood based cabinet and bass reflex sound system.
Highly sensitive built-in FM/AM antenna.
Full range 3 inch speaker and cancel magnet system.
LINE IN jack for connecting other portable audio equipment.
LINE OUT jack to use the unit as a highly sensitive discrete tuner.
Headphone out (ø3.5mm stereo minijack).

Setting the clock

Plug in the unit.
The display will flash "AM 12:00" or "0:00".
Press OPERATEto turn off the radio when it is turned on.
Press and hold BAND/CLOCKfor a few seconds.
You will hear a beep and the hour will start to flash in the display.
The following illustration's time display is a 24-hour system.
Turn TUNE/TIME SETright or left until the correct hour appears in the display.
Press BAND/CLOCKonce.
The hour is set and the minutes start to flash.
Repeat steps 4and 5to set the minute.
Two short beeps sound, ":" starts flashing, and the clock starts operating.
The clock system varies depending on the model you own.
12-hour system: "AM 12:00" = midnight.
24-hour system: "0:00" = midnight.

If you do not set the clock within 65 seconds, the setting is cancelled.

Operating the radio

Press OPERATEto turn on the radio.
If "LINE" is displayed, press RADIO/LINE INso that the frequency appears.
Press BAND/CLOCKto select the band AM or FM.
Turn TUNE/TIME SETright or left to tune in to a desired frequency.
Two short beeps sound when the minimum frequency of each band is received during tuning.
Adjust the volume using VOLUME.
Set the tone using TONE.
To adjust the tone, turn TONEto LOW/HIGH.

To listen with the headphones
You can enjoy the radio and external equipment connected to the line in by the headphones (not supplied). Connect the headphones (not supplied) to the (headphones) jack. The speaker is deactivated when the headphones are connected. The headphones output AM broadcasts in monaural (same sound is output from both headphones), while FM stereo broadcasts are output in stereo.

Improving the reception

FM: The AC power cord functions as an FM antenna. Extend the AC power cord fully to increase reception sensitivity.
Improving the reception - Step 1

AM: Rotate the unit horizontally for optimum reception. A ferrite bar antenna is built into the unit.
Improving the reception - Step 2

Note
Do not play the unit over a steel desk or metal surface, as this may lead to interference of reception.

Connecting external equipment

To listen to sound

Connect the LINE INjack of the unit to the line out jack or headphone jack of the external equipment using the audio connecting cable (supplied).
Press OPERATEto turn on the radio.
Press RADIO/LINE INto select "LINE" in the display.
Play the equipment connected to the LINE INjack.
Adjust the volume using VOLUME.

To return to the radio
Press RADIO/LINE IN.
The frequency is shown in the display.

To record with LINE OUT

Connect the LINE OUTjack of the unit to the line in jack of the external equipment using the audio connecting cable (supplied).
Press OPERATEto turn on the radio.
Tune the unit to the radio station that you want to record.
Start to record on the connected equipment.

Notes

Refer also to the connected equipment's manual.
The supplied audio connecting cable may not be used with some external equipment. In this case, use a cord suitable for the external equipment you are using.
LINE OUT signal of AM broadcasts is output in monaural (same sound is output from both headphones). And LINE OUT signal of FM stereo broadcasts is output in stereo.
The sound quality of LINE OUT signal is constant regardless of the position of TONE, and the output level is constant regardless of the position of VOLUME.
When you listen to the radio with external equipment connected, turn off the connected equipment because noise may be caused. If noise continues, even when the equipment is turned off, disconnect and place the external equipment away from the unit.
If there are line out and headphone jacks on external equipment, connect to the line out jack.
If you connect with the headphone jack of the external equipment, some equipment may not perform tone switch function (e.g., bass boost, equalizer etc.).

Precautions

Play the unit on the power source specified in "Specifications".
To disconnect the AC power cord (mains lead), pull it out by the plug, not the cord.
The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
The nameplate indicating operating voltage, etc. is located on the bottom exterior.
Since a strong magnet is used for the speaker, keep personal credit cards using magnetic coding or springwound watches away from the unit to prevent possible damage from the magnet.
Do not leave the unit in a location near a heat source such as a radiator or airduct, or in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock.
To reduce the risk of fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. And do not place lighted candles on the apparatus.
Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on a surface (a rug, a blanket, etc.) or near materials (a curtain) which might block the ventilation holes.
Should any solid object or liquid fall into the unit, unplug the unit and have it checked by a qualified personnel before operating it any further.
To clean the casing, use a soft cloth dampened with a mild detergent solution.

If you have any questions or problems concerning your unit, please consult your nearest Sony dealer.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.