Cisco BPX 8600 Series Installation Manual
Cisco systems hub/switch installation and configuration guide
Hide thumbs
Also See for BPX 8600 Series:
- Dimensions (14 pages) ,
- Installation and configuration manual (630 pages) ,
- Quick reference manual (38 pages)
Table of Contents
Advertisement
Quick Links
C H A P T E R
2
Installation
This chapter explains how to install an IPX 8/16/32.
Site Preparation
The IPX 8/16/32 site must meet the following requirements:
•
Space
Each IPX 16/32 cabinet requires a floor space of 22 inches (55.9 cm) wide and 80 inches
(203.2 cm) deep. Each IPX 8 cabinet requires a floor space 19 inches (48.25 cm) wide and
24 inches (61.0 cm) deep. This depth measurement allows for opening the front and back cabinet
doors. Sufficient clearance around the cabinet is also necessary to allow access to the front and
back of the cabinet while the doors are open.
•
Power
An AC or DC power source must be available within six feet of the IPX 16/32 cabinet. At 180 to
264 VAC, an IPX 16 may require up to 9.2 A maximum (1700 VA) and an IPX 32 up to 17 A
maximum (3100 VA). At –42 to -56 VDC, an IPX 16 may require up to 28 A maximum (1200
W) and an IPX 32 up to 50 A maximum (2100 W).
•
Cooling
The site must be capable of maintaining an ambient temperature of 40˚C (max.) while the system
is operating (recommended range is 20˚C to 30˚C). Each fully loaded IPX 8 node dissipates
approximately 1300 BTUs (0.38 KW hour) to the room; the IPX 16 cabinet, 3419 BTUs (1 KW
hour), and the IPX 32 cabinet, 6836 BTUs (2 KW hour).
•
Weight
Each fully loaded IPX 32 cabinet can weigh up to 700 lbs (318 kgs). A fully loaded IPX 16
cabinet can weigh up to 400 lbs (182 kgs). Each fully loaded IPX 8 cabinet can weigh up to
125 lbs. (55 kgs).
•
Flooring
Raised flooring with sufficient under-floor space to house the cables is recommended.
•
Mounting
The IPX 8 cabinet can be mounted in a rack or be left free-standing. The location of the IPX
should give consideration to the routing of the data cables and the termination of the telephone
company or common carrier circuits.
Installation 2-1
Advertisement
Table of Contents
Related Manuals for Cisco BPX 8600 Series
Summary of Contents for Cisco BPX 8600 Series
-
Page 1: Site Preparation
C H A P T E R Installation This chapter explains how to install an IPX 8/16/32. Site Preparation The IPX 8/16/32 site must meet the following requirements: • Space Each IPX 16/32 cabinet requires a floor space of 22 inches (55.9 cm) wide and 80 inches (203.2 cm) deep. -
Page 2: Seismic Considerations
Site Preparation Seismic Considerations To provide protection against seismic activity, the IPX 16/32 cabinet is equipped with holes that permit the cabinet to be bolted to a concrete floor or to a structural member in the floor. The cabinet base has four sets of holes (two sets at the lower front and two sets at the lower rear). Each set consists of a large socket access hole above a smaller hole. -
Page 3: Required Tools And Equipment
Figure 2-2 3/8" hole 7/8" access hole (4 places) Required Tools and Equipment The following tools and equipment are required to install the IPX: • Flat blade screwdriver set • Phillips screwdriver set • Grounding wrist strap • DVM (digital voltmeter) •... - Page 4 Multi-Cabinet Installations (IPX 16/32) Multi-Cabinet Installations (IPX 16/32) For installations in which multiple IPX 16/32 cabinets stand next to each other, an optional kit is available from StrataCom that provides brackets and screws for clamping the cabinets together. The Cabinet Side by Side Mounting Kit (Part No. 210372-00) consists of two top-mounting brackets, two bottom-mounting brackets, and two screws.
- Page 5 Figure 2-4 Cabinets Joined at the Top cabinet 1 cabinet 2 Step 2 Insert the mounting bracket between the underside of the cabinet and the lock nut so that the screw supporting the cabinet foot slides into the L shaped recess. Rotate the mounting bracket towards the second cabinet so that the straight recess slides Step 3 around the screw in the second cabinet (Figure 2-6).
- Page 6 Multi-Cabinet Installations (IPX 16/32) Figure 2-6 Initial position Figure 2-7 Mounting bracket 2-6 IPX Installation Manual Positioning the Bottom Mounting Bracket (IPX 16/32) Screws supporting cabinet foot IPX 16/32 Cabinets Joined at the Bottom cabinet 1 Lock nut Lock nut Floor Cabinet feet Final position...
-
Page 7: Free-Standing Installation
IPX 8 Cabinet Installation The IPX 8 cabinet can be mounted either in an equipment rack or left free-standing. It is self-contained and small enough to stand on a flat support such as a table or bench. For rack-mounting the IPX 8, the appropriate, optional rack-mounting kit should be ordered to obtain the appropriate mechanical mounting hardware. - Page 8 IPX 8 Cabinet Installation Figure 2-8 Screw 2-8 IPX Installation Manual Installing Rack Mounting Kit IPX8 6 0 2 7 P o w e r S u p A C L p ly o g ic F a ile A c ti v 6 0 2 7 P o w e r S u p...