Advertisement
Installating the wire controller
1. Remove upper cover of wire controller
Remove upper part of wire controller by press.
PCB is mounted on lower part of wire
controller, be careful not to damage it.
2. Install the wired remote controller
Please drill two holes on the wall according to the
back cover screw hole position of the wire remote
controller, then strike the wood block to the holes
respectively, then align the 2 screw hole of the wire
controller back cover to the wood block, fasten the
wire reote controller to the wall use wood screws.
3. Switch setting
The switchs setting as follows:1.ON 2.OFF 3.ON 4.OFF
Note
Try as far as possible a flat surface for installation.
Don't use excessive force when tightening screws,
or lower part might got deformed.
4. Connecting method as the following chart
contents
No Symbol
colour
1
A
White or Green
12V
2
B
Red
Gnd
3
C
Yellow
COM
4
D
Use shielede wires for telecommunication
between wire controller and indoor unit;
indoor unit and outdoor unit. Ground the
shield on one side.
Otherwise misoperation because of noise
may occur.
Signal wire is self-provided by user.
5. Replace the upper cover of wire controller
Be careful not to hold down the wiring.
Hint 1. Power supply switch and signal wire should be prepaired by the user.
2. Don't touch PCB with hand.
Upper cover of wire
controller
Lower cover of wire
controller
Switch button
Screw hole
Back cover of the wire
controller
Shielded wire
ground
11
OPERATION MANUAL
YR-E06&YR-H71
Table of Contents
Parts and Functions
Operation
Health Function and Installating the Reciever
Installating the wire controller
No. 0010573682
C
Please read this operation manual before using the air conditioner.
Please keep this manual carefully and safely.
1-4
5-9
10
11
Advertisement
Table of Contents
Related Manuals for Haier YR-E06
Summary of Contents for Haier YR-E06
- Page 1 Switch button Screw hole Back cover of the wire controller Shielded wire No. 0010573682 Please read this operation manual before using the air conditioner. Please keep this manual carefully and safely. YR-E06&YR-H71 Table of Contents Parts and Functions Operation Health Function and Installating the Reciever...
-
Page 2: Parts And Functions
Parts and Functions Left picture is a wired remote controller, which can be used on Series wired control units ,The remote controller can be purchased extrally. Wired remote Controller using method: 1.Use one wired remote controller. See fig (1) 2.Also can buy a remote controller extrally, realize fig(1) wired remote control + remote control dual control modes. -
Page 3: Operation
Concerning MRV Auto Restart function for H-MRV models Haier Auto Restart function when the unit power drops down suddenly, the unit microprocessor will store the previous working condition and when the power is on again, the unit will run as this memory. -
Page 4: Remote Controller
Used to select operation mode. heating or cooling. NOTE: 1.Single cooling air conditioner does not have the displays and functions related to heating. 2.Some functions of this controller maybe not available according to the corresponding PCB's functions,such as: In function of code A which are optional for different unit. -
Page 5: Remote Controller Operation
Operation MODE SWING TEMP HEALTH CLOCK TIMER SLEEP HEAT FILTER RESET RESET ON/OFF The function of code A:TIMER ON/OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. Power indicator lights up. (2) Press TIMER button to change TIMER mode Every time the button is pressed, display changes as (4) Time confirming for TIMER follows:... -
Page 6: Timer On/Off
Operation Recommendations Use COOL in summer.Use HEAT in winter. Use DRY in spring,autumn and in damp climate. (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display (Not Timer setting). Power indicator lights up. (2) Select operation mode AUTO Press MODE button.