Mitsubishi Electric MSZ-SF35VE Installation Manual
Hide thumbs
Also See for MSZ-SF35VE:
- Operating instructions manual (124 pages) ,
- Installation manua (56 pages) ,
- Service manual (44 pages)
Advertisement
INSTALLATION MANUAL
1. BEFORE INSTALLATION
1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY
Do not install the unit by yourself (user).
due to the unit falling, or leakage of water. Consult the dealer
Perform the installation securely referring to the installa-
tion manual.
due to the unit falling, or leakage of water.
When installing the unit, use appropriate protective equip-
ment and tools for safety.
Install the unit securely in a place which can bear the
weight of the unit.
rienced electrician, according to the installation manual.
electrical appliances to the circuit.
shock.
Earth the unit correctly.
Do not connect the earth to a gas pipe, water pipe, lightning
shock.
with parts or screws.
Be sure to cut off the main power in case of setting up the
indoor P.C. board or wiring works.
Failure to do so could cause electric shock.
block connecting sections so the stress of the wires is
use intermediate connection.
Install an earth leakage breaker depending on the instal-
lation place.
electric shock.
Perform the drainage/piping work securely according to
the installation manual.
1-2. SELECTING THE INSTALLATION LOCATION
INDOOR UNIT
direct sunshine also during the period following unpacking
REMOTE CONTROLLER
• Where children cannot touch it.
holder to a pillar or wall and install wireless remote control-
ler.
1-3. SPECIFICATIONS
Model
Indoor unit
Outdoor unit
power switch is shut off, it must interrupt all phases.)
Model names are indicated in 1-3.
When installing multi units, refer to the
installation manual of the multi unit for
outdoor unit installation.
WARNING
may leak.
If gas leaks and accumulates in the area around the unit, it
Do not use intermediate connection of the power cord or
one AC outlet.
etc.
the installation work.
-
When plugging the power supply plug into the outlet,
make sure that there is no dust, clogging, or loose parts
in both the outlet and the plug. Make sure that the power
supply plug is pushed completely into the outlet.
Attach the electrical cover to the indoor unit and the
service panel to the outdoor unit securely.
When installing, relocating, or servicing the unit, make
(R410A) enters the refrigerant circuit.
CAUTION
from the unit, soaking and damaging household goods.
outdoor unit.
Note:
OUTDOOR UNIT
hot air.
the unit legs.
Breaker
2
1.0 mm
50 Hz
2.0 mm
2
ing.
-
Required Tools for Installation
Scale
65 mm hole saw
Do not discharge the refrigerant into the atmosphere. If
refrigerant leaks during installation, ventilate the room.
Check that the refrigerant gas does not leak after instal-
lation has been completed.
If refrigerant gas leaks indoors, and comes into contact with
-
Use appropriate tools and piping materials for installa-
tion.
appropriate tools or materials and incomplete installation could
When pumping down the refrigerant, stop the compressor
before disconnecting the refrigerant pipes.
If the refrigerant pipes are disconnected while the compressor
When installing the unit, securely connect the refrigerant
pipes before starting the compressor.
this manual.
and cause refrigerant leakage.
The unit shall be installed in accordance with national
wiring regulations.
Do not install the outdoor unit where small animals may
live.
If small animals enter and touch the electric parts inside the
Note:
Note:
When operating the air conditioner in low outside tempera-
its air inlet side facing the wall.
•
• Where there is much machine oil.
cause chemical cracking.
Pipe size
connecting wire
4-core
1.0 mm
2
-
Pipe cutter with reamer
Pipe length and height difference
10
8 mm
-
-
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric MSZ-SF35VE
Summary of Contents for Mitsubishi Electric MSZ-SF35VE
- Page 1 Required Tools for Installation Scale Model names are indicated in 1-3. When installing multi units, refer to the 65 mm hole saw installation manual of the multi unit for Pipe cutter with reamer INSTALLATION MANUAL outdoor unit installation. 1. BEFORE INSTALLATION 1-1.
-
Page 2: Indoor Unit Installation
1-4. INSTALLATION DIAGRAM Be sure to use wall hole Indoor unit ACCESSORIES Seal the wall hole gap <Indoor unit> Wall hole metal parts in the wall Installation plate rodents in case the wall 4 × 25 mm is hollow. Cut off the ×... -
Page 3: Outdoor Unit Installation
Left or left-rear piping Rear, right, or downward piping Cut off in case of Note: 1) Put the refrigerant piping and the drain hose right piping. Be sure to reattach the drain Cut off in case of left hose and the drain cap in case the end. -
Page 4: Purging Procedures, Leak Test, And Test Run
4. PURGING PROCEDURES, LEAK TEST, AND TEST RUN 4-2. TEST RUN 4-1. PURGING PROCEDURES AND LEAK TEST , and twice for opera- gas pipe side of the outdoor unit. Compound pressure gauge 0.101 MPa Pressure gauge operation switch Handle Checking the remote (infrared) signal reception Handle High Charge hose 140 to... - Page 5 Related Links Model Number: MSZ-SF25VE MSZ-SF20-50 and MUZ-SF25-50 Declaration of Conformity MSZ-SF20-50VE / MUZ-SF25-50VE Installation Manual MSZ-SF25-50VE Instruction Book (SG79F674H02) MSZ-SF25-50VE Parts Catalogue (OBB600E) MSZ-SF25-50VE Service Manual (OBH600A)