Advertisement
Quick Links
Thank you for purchasing a Sealey product. manufactured to a high standard this product will, if used according to these instruc-
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS, AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY.
1.
SAFETY INSTRUCTIONS
1.1
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with
the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power
cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of
electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit
Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a
Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products
that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified
electrician.
You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions
concerning electrical safety.
1.1.1 The Electricity at Work Act 1989 requires that all portable electrical
appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a
year.
1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical
appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about
electrical safety, contact a qualified electrician.
1.1.3 Ensure that the insulation on all cables and on the appliance is safe
before connecting it to the power supply. See 1.1.1 and 1.1.2 and use a
Portable Appliance Tester.
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Regularly inspect power supply cables and plugs for wear or damage and check all connections to
ensure that none is loose.
1.1.6 Important: Ensure that the voltage marked on the appliance matches the power supply to be used and
that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7 DO NOT pull or carry the appliance by the power cable.
1.1.8 DO NOT pull the plug from the socket by the cable.
1.1.9 DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item
repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is damaged,
cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a)
b)
c)
d)
correctly connected, that the cable outer insulation extends beyond the cable restraint and that
the restraint is tight. Double insulated products, which are always marked with this symbol
fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as indicated
above - DO NOT connect either wire to the earth terminal.
1.1.10 Products which require more than 13 amps are supplied without a plug. In this case you must contact a
qualified electrician to ensure that a suitably rated supply is available. We recommend that you discuss
the installation of an industrial round pin plug and socket with your electrician.
1.1.11 If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and
should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this
product and for others which may be used in the other output sockets, we recommend the use of 2.5mm²
section cable.
tions and properly maintained, give you years of trouble free performance.
Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
Connect the BROWN live wire to the live terminal 'L'.
Connect the BLUE neutral wire to the neutral terminal 'N'.
After wiring, check that there are no bare wires, that all wires have been
Original Language Version
InSTRUCTIonS foR:
HALOGEN PATIO HEATER 2100W/230V
EPH2100
moDElS:
Blue
Neutral
Wire
FUSE RATING 13 AMP
Yellow & Green
Earth Wire
Brown
Live
Wire
Cable
Restraint
, are
EPH2100
Issue: 1 - 26/07/10
Advertisement
Related Manuals for Sealey EPH2100
Summary of Contents for Sealey EPH2100
- Page 1 EPH2100 moDElS: Thank you for purchasing a Sealey product. manufactured to a high standard this product will, if used according to these instruc- tions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS.
- Page 2 ASSEMBLY INSTRUCTIONS 3.1 Thread cable through base and into the base 3.2 fix the base tube to the base using the 3 x tube. Pull through approx. 2mtr of cable. m6 bolts. Original Language Version EPH2100 Issue: 1 - 26/07/10...
- Page 3 3.9 Carefully lay heater on its side. fix the cable to 3.10 Shows secured cable. the base using the two plastic cable clamps. Original Language Version EPH2100 Issue: 1 - 26/07/10...
- Page 4 WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, www.sealey.co.uk...