Table of Contents
Advertisement
Quick Links
Hydraulic Power Pack
ProPass 200 Top Dresser with Tow-Type Chassis
Model No. 44713—Serial No. 403300001 and Up
This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
1. Warning—do not touch the hot surface.
1. Cutting/dismemberment hazard of hand, conveyor—stay
away from moving parts, keep all guards and shields in
place.
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Proposition 65 Warning
reproductive harm. Wash hands after handling.
115-2047
119-6844
Register at www.Toro.com.
WARNING
CALIFORNIA
decal115-2047
1. Warning—no step
decal119-6844
Form No. 3424-682 Rev A
Installation Instructions
119–6807
Original Instructions (EN)
All Rights Reserved *3424-682* A
Printed in the USA
decal119-6807
Advertisement
Table of Contents
Related Manuals for Toro 44713
Summary of Contents for Toro 44713
- Page 1 Form No. 3424-682 Rev A Hydraulic Power Pack ProPass 200 Top Dresser with Tow-Type Chassis Model No. 44713—Serial No. 403300001 and Up Installation Instructions This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
- Page 2 decal119-6829 119–6829 1. Read the Operator's Manual. 2. Maximum load of 907 kg (2000 lb) results in an axle weight of 1,530 kg (3320 lb) and a tongue weight of 145 kg (320 lb ). 3. Empty hopper has an axle weight of 599 kg (1320 lb) and a tongue weight of 48 kg (105 lb).
-
Page 3: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty. Hydraulic tank assembly Prepare the machine Hose guide mounting bracket Engine assembly Bolt (1/2 x 5 inches) Battery Battery hold down Battery mount strap Mount the engine. -
Page 4: Preparing The Machine
Important: This kit can only be applied to a ProPass that is equipped as a tow-behind machine. Preparing the Machine CAUTION Installing the kit before disconnecting all external hydraulic and electrical sources may expose you to electric shock and/or pressurized hydraulic fluid, causing serious injury or death. -
Page 5: Mounting The Engine
Mounting the Engine Have someone help you to position the engine assembly onto the hitch tube. Ensure that the hitch tube is clean and free from Ensure that the engine mount brackets straddle dirt or debris. the hitch tube (Figure 5) and that the rear of the Unpack the engine assembly. - Page 6 Insert the 2 bolts (1/2 x 5 inches) through the On the left side, install a battery bolt through engine mount bracket holes, ensuring that a flat the washer, battery mount strap, engine mount washer is fitted against each outer face of the plate, battery tray, battery bolt spacer, and hold engine mount bracket, and ensuring that the down.
- Page 7 Installing the Hydraulic The hose guide should sit on top of the tab from the vertical leg of the battery tray (Figure 10). System If the holes in the hose guide do not match the holes in the battery tray tab, the hose guide Unpack the hose guide, hydraulic return hose length may be adjusted by loosening the bolts (hose #3), hydraulic suction hose (hose #4), 4...
- Page 8 Connect hydraulic hose #4 to the suction side of Identify the pressure and return connections on the hydraulic pump (Figure 12). the machine base model. Refer to Figure 14 for the SH versions and Figure 15 for the EH versions. g013908 Figure 12 g014215...
-
Page 9: Completing The Installation
Completing the Installation If pressure and return hoses were previously installed at the locations shown in Figure 14 Refit the Twin Spinner assembly. Figure 15, remove them. Connect the black cable and the black pre-routed Note: Ensure that the hoses do not contact cable to the battery negative terminal and the any hot, sharp, or moving parts. -
Page 10: Operation
Operation Fill the engine with approximately 1 L (34 fl oz) of the proper viscosity oil before starting; refer to Servicing the Engine Oil (page 10). CAUTION Important: The engine is shipped from the factory without oil; attempting to start the Ensure that all control systems are turned off machine before you fill it with oil will cause when working on the power pack. -
Page 11: Servicing The Hydraulic System
(Available in 5 gallon pails or 55 gallon drums. See parts catalog or Toro distributor for part numbers.) Filling the Fuel Tank Alternate fluids: If the Toro fluid is not available, other petroleum-based Universal Tractor Hydraulic Fluids Fuel Tank Capacity: 6.1 L (1.6 US gallons) -
Page 12: Activating And Charging The Battery
Activating and Charging WARNING the Battery Charging the battery produces gasses that can explode. Use only electrolyte (1.265 specific gravity) to fill Never smoke near the battery and keep battery initially. sparks and flames away from battery. Clean the top of the battery and remove the vent caps (Figure 21). - Page 13 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 14 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 15 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.