Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
maintain the tool in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable clean and tidy work area, free from unrelated materials and with adequate lighting.
9
Before each use check pad for condition. If worn or damaged replace immediately.
9
Ensure the pad rating is the same as, or greater than, the RPm rating of the tool.
9
Ensure there are no flammable or combustible materials near the work area.
9
WARNING! Always wear approved eye or face and hand protection when operating the tool.
‰
Use face, dust, or respiratory protection in accordance with COSHH regulations.
9
Depending on the task, noise levels may exceed 87dB in which case wear safety ear defenders.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
Ensure workpiece is secure before operating the tool. Never hold a workpiece by hand.
9
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
9
Avoid unintentional starting.
9
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Prolonged exposure to vibration from this tool poses a health risk. It is the owner's responsibility to correctly assess the potential hazard
9
and issue guidelines for safe periods of use and offer suitable protective equipment.
DO NOT use the tool for a task it is not designed to perform.
8
DO NOT operate tool if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WARNING! DO NOT use on any materials containing asbestos.
‰
DO NOT carry the tool by the hose, or yank the hose from the air supply.
8
DO NOT operate tool when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry the tool with your finger on the power lever.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODucTION
Composite cover moulded around lightweight aluminium alloy housing reduces effects of chill on operator's hands and provides added control. Air
motor with quality bearings for smooth and powerful operation. Exhaust outlet adjusts 360° keeping air flow away from operator. Ideal for removing
pinstripes or double-sided tape from panel prior to refinishing. Suitable for the professional workshop.
3. SPEcIFIcATION
model no .................................................................. SA95.V3
Free speed ............................................................... 2500rpm
Pad size .............................................................Ø88 x 15mm
Inlet size ....................................................................1/4"BSP
Operating pressure ....................................................... 90psi
Weight .............................................................................. 1kg
Noise power/pressure ........................................ 103/92dB(A)
Vibration/uncertainty ........................................ 0.49/0.54m/s²
Thread size .............................................................. 1/4"UNC
Replacement pad .....................................................SA95/PX
© Jack Sealey Limited
AIR ADHESIVE STRIPE REMOVAL TOOL PREMIER
mODEL NO:
Wear a mask Wear protective
gloves
Original Language Version
SA95.V3
Wear ear
protection
SA95.V3 | Issue:2 (H,F) 19/12/18
Advertisement
Related Manuals for Sealey SA95.V3
Summary of Contents for Sealey SA95.V3
- Page 1 SA95.V3 mODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty. 7.1.1. If there is no oiler in the air supply system, lubricate the tool daily with a few drops of good grade air tool oil such as Sealey ATO/500 or ATO1000, dripped into the air inlet before use.
- Page 3 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...