Page 1
Installation and Operating Instructions Ceramic Glass Hob C61RAAST / C61RABAL / C61RACN / C61RADST / C61RAEE / C61R1AAMST / C61R1ABMAL / C61R1ACMN / C61R1ADMST / C61R1AEME / C61R2AAST / C61R2ABAL / C61R2ACN / C61R2ADST / C61R2AEE To avoid the risk of accidents or damage to the hob, read all instructions before installing or using the appliance.
Page 2
C Top_MID] C61RAAST_XFA-00131A-05_EN.indd 2 1/11/2555 11:17:17...
Using This Manual Please take the time to read this owner’s manual, paying particular attention to the safety information contained in the following section, before using your appliance . Keep this manual for future reference . If transferring ownership of the appliance, please remember to pass the manual on to the new owner .
Safety The safety aspects of this appliance comply with accepted technical standards and the German Appliance Safety Law . However, as manufacturers we also believe it is our responsibility to familiarise you with the following safety instructions . Electrical safety •...
Safety (continued) Safety during use • This appliance is to be used only for normal cooking and frying in the home. It is not de- signed for commercial or industrial use . • Never use the hob for heating the room. •...
Installing the Hob Important: Be sure the new appliance is installed and grounded only by qualified personnel . Please observe this instruction . The warranty will not cover any damage that may occur as a result of improper installation . Technical data is provided at the end of this manual .
Installing the Hob (Continued) Connecting to the mains power supply Before connecting, check that the nominal voltage of the appliance, that is, the voltage stated on the rating plate, corresponds to the available supply voltage . The rating plate is located on the lower casing of the hob .
Installing the Hob (Continued) Installing into the countertop Make a note of the serial number on the appliance rating plate prior to installation. This number will be required in the case of requests for service and is no longer ac- cessible after installation, as it is on the original rating plate on the underside of the appliance .
Page 10
Installing the Hob (Continued) C Top_MID] C61RAAST_XFA-00131A-05_EN.indd 8 1/11/2555 11:17:17...
Parts and Features Cooking zones and control panel Single cooking zone 1800W Single cooking zone 1200 W Single cooking zone Control panel 1200 W Single cooking zone 1800W Indicators for heat settings “Lock” control sensor and residual heat Heat setting selectors “On/Off”...
Parts and Features (Continued) Components Ceramic Glass Hob Installation Brackets Screws C Top_MID] C61RAAST_XFA-00131A-05_EN.indd 10 1/11/2555 11:17:17...
Parts and Features (Continued) The key features of your appliance • Ceramic glass cooking surface: The appliance has a ceramic glass cooking surface and four rapid - response cooking zones. The hob’s powerful radiant heater elements significantly shorten the amount of time required for the zones to heat up. •...
Parts and Features (Continued) Safety shutoff If one of the cooking zones is not switched off or the heat setting is not adjusted after an ex- tended period of time, that particular cooking zone will automatically switch itself off . Any residual warmth will be indicated with (for “hot”) in the digital displays corresponding to the particular cooking zones .
Before You Begin Initial cleaning Wipe the ceramic glass surface with a damp cloth and ceramic cooktop glass cleaner. Important: Do not use caustic or abrasive cleaners. The surface could be damaged. Hob Use Using suitable cookware Better pans produce better results. •...
Hob Use (Continued) • Always position pots and pans before switching on the cooking zone. • Dirty cooking zones and pan bases increase power consumption. • When possible, position the lids firmly on the pots and pans to cover completely. •...
Hob Use (Continued) Switching the appliance on Touch the “Lock ” sensor for approximately 3 seconds . The appliance is switched on using the “On / Off ” control sensor . Touch the “On / Off ” sensor . The digital displays will show After the “On / Off ”...
Hob Use (Continued) Switching the appliance off To completely switch off the appliance, use the “On / Off ” control sensor . Touch the “On / Off ” sensor . After switching off a single cooking zone or the entire cooking surface, the presence of residual heat will be indicated in the digital displays of the corresponding cooking zones in the form of an (for “hot”).
Hob Use (Continued) Using the child safety lock You can use the child safety lock to safeguard against unintentionally turning on a cooking zone and activating the cooking surface . The lock control sensor can be used only when the power is on .
Page 20
Hob Use (Continued) Switching the child safety lock off 1 . Touch the control sensor for approximately 3 seconds . An acoustic signal will sound as confirmation. approx. 3 sec. After switching off the appliance, child safety lock will be activated automatically within some minutes for safety reasons .
Hob Use (Continued) Locking and unlocking the control panel At any stage during the cooking process, the control panel, with the exception of the “On / Off ” control sensor, can be locked in order to prevent the settings from being changed uninten- tionally, for example, by wiping over the panel with a cloth .
Cleaning and Care Important: Cleaning agents must not come into contact with a heated ceramic glass surface: All cleaning agents must be removed with adequate amounts of clean water after cleaning because they can have a caustic effect when the surface becomes hot.
Cleaning and Care (Continued) Problem Dirt 1 . Remove burnt-on sugar, melted plastic, aluminium foil or other materials with a glass scraper immediately and while still hot . Important: There is a risk of burning yourself when the glass scraper is used on a hot cooking zone: 2 .
Warranty and Service FAQs and troubleshooting A fault may result from a minor error that you can correct yourself with the help of the following instructions. Do not attempt any further repairs if the following instructions do not help in each specific case.
Warranty and Service (Continued) What does it mean when the burner does not glow red? • The selected temperature of the cooking zone is maintained by a sensor that cycles the zone on and off, so the surface cooking area will not always glow red . If you select a low heat setting, the heat will cycle on and off more frequently than at higher settings.
Technical Data Appliance dimensions Width 575 mm Depth 505 mm Height 55 mm Worktop cut - out dimensions Width 560 mm Depth 490 mm Corner radius 3 mm Cooking rings Position Diameter Power Front left 183 mm 1,800 W Rear left 148 mm 1,200 W Rear right...
Page 27
NOTE C Top_MID] C61RAAST_XFA-00131A-05_EN.indd 25 1/11/2555 11:17:18...
Page 28
SOUTH AFRICA 0860-SAMSUNG (726-7864 ) NIGERIA 0800 - SAMSUNG (726-7864) U.A.E 800-SAMSUNG (726-7864) OMAN 800-SAMSUNG(726-7864) KUWAIT 183-2255 BAHRAIN 8000-4726 ww w.samsung.com EGYPT 08000-726786 JORDAN 800-22273 MOROCCO 080 100 2255 SAUDI ARABIA 9200-21230 TURKEY 444 77 11 ww w.samsung.com IRAN 021-8255 www.samservice.com...