Table of Contents
Advertisement
Quick Links
Cab Kit
Workman
Model No. 07142—Serial No. 316000001 and Up
Model No. 07142—Serial No. 400000000 and Up
Important:
The Power Converter Kit is required
to use the cab on a Workman GTX Electric utility
vehicle. Contact your authorized Toro distributor
for more information.
Important:
The Spring Kit is required to use
the cab on a Workman GTX utility vehicle. The
Spring Kit should be installed only by qualified
Toro Service Technicians using approved tools.
Improper removal, disassembly, or installation of
the spring assembly poses a danger to you and
bystanders. Please contact your authorized Toro
distributor for the appropriate tools and proper
installation of this kit.
Safety
WARNING
The compressed spring in the spring and
shock assembly represents a stored-energy
hazard. If the spring is not properly retained
during compression or removal, it can injure
you and/or bystanders.
• Always use the approved Toro
spring-compression tool to compress the
spring in a secure position when removing
the retention collar.
• Always use care when removing pressure
from the compressed spring.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
GTX Utility Vehicle
Register at www.Toro.com.
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. Warning—read the
Operator's Manual; wear
the seatbelt, and avoid
tipping the machine.
Original Instructions (EN)
All Rights Reserved *3432-927* A
Printed in the USA
Form No. 3432-927 Rev A
Operator's Manual
133-1016
2. Warning—wear hearing
protection.
decal133-1016
Advertisement
Table of Contents
Related Manuals for Toro Cab Kit
Summary of Contents for Toro Cab Kit
- Page 1 Important: The Power Converter Kit is required to use the cab on a Workman GTX Electric utility Decals vehicle. Contact your authorized Toro distributor for more information. Safety decals and instructions are easily visible to the operator and are Important:...
- Page 2 decal130-5964 130-5964 1. Warning—in the event of an emergency 1) Pull the locking pin out of each hinge; 2) Push the front window out to exit. decal133-1017 133-1017 1. Do not repair or revise—read the Operator's Manual. decal131-8410 131-8410 1. Fire hazard—shut off the engine before fueling. decal120-9570 120-9570 1.
-
Page 3: Table Of Contents
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Remove the strut assembly (for 2018 – No parts required and before machines only). Install the springs (for 2018 and before Spring machines only). - Page 4 Preparing the Machine No Parts Required Procedure Park the machine on a level surface, set the parking brake, shut off the engine, and remove the key. Raise the bed until the bed prop rod is fully engaged; refer to the Operator’s Manual for the machine. Remove the seat base.
-
Page 5: Spring
g038284 Figure 1 Hood and fender not shown to show the shock-mount bracket 1. Hex-head bolt (1/2 x 2-1/4 inches) 6. Flange nut (3/8 inch)—from the control arm 2. Locknut (1/2 inch) 7. Flange nut (3/8 inch)—from the spindle 3. Collar 8. -
Page 6: No Parts Required
No Parts Required Procedure Procedure Install strut assembly to the machine. Use an approved Toro spring-compression tool to remove and install springs of the strut assembly. Secure the upper portion of the strut assembly Contact your authorized Toro distributor. to the frame using the upper, hex-head bolt (1/2... -
Page 7: Floor-Plate Support
Use a floor jack under the frame to support the front of the machine (Figure Installing the Supports Parts needed for this procedure: Floor-plate support Flange-head bolt (5/16 x 1-1/4 inches) Flange nut (5/16 inch) Left cab support Right cab support Hex-head bolt (3/8 x 1-1/4 inch) g038334 Figure 3... - Page 8 Install a new floor-plate support using 8 Using the new floor-plate supports as a guide, flange-head bolts (5/16 x 1-1/4 inches) and 8 drill 3 holes (3/8-inch diameter) into each floor flange nuts (5/16 inch) as shown in Figure plate (Figure Note: Important:...
-
Page 9: Cab Frame
Remove the 3 screws and 3 nuts securing the left handhold, and remove it (Figure Installing the Cab Parts needed for this procedure: Cab frame Back foam seal Back foam seal carpet g037177 Figure 9 Flange-head bolt (5/16 x 1-1/4 inches) Flange nut (5/16 inch) 1. -
Page 10: Hex-Head Bolt (3/8 X 1-1/4 Inches)
Lift the cab frame using the lift points and place Secure the back of the cab frame to the left and it on the machine (Figure 11). right supports using 4 flange-head bolts (5/16 x 1-1/4 inches), 2 support plates, 4 flat washers, and 4 flange nuts (5/16 inch) as shown in Figure Note:... - Page 11 Install the seat base. Note: You may need to position the 2 center seat-belt anchors to allow the seat to drop into place. Loosen the 2 locknuts (7/16 inch) on the 2 center seat-belt anchors, and tighten the 2 locknuts (7/16 inch) to 72 to 88 N∙m (53 to 65 ft-lb) after adjusting the position.
-
Page 12: Fuse Block
The Power Converter Kit is required to use the cab on a Workman GTX Electric utility g290937 Figure 18 vehicle. Contact your authorized Toro distributor for more information. 1. New fuse block 3. Serrated nut (#10) 2. Hex-washer head screw 4. - Page 13 Route the wire harness behind the cab and Connect the remaining wire to the fused wire on under the seat, and secure the clip on the wire the new fuse block (Figure 17). harness to the side panel (Figure 19). Lower the bed and connect the battery;...
- Page 14 For Gasoline/Petrol or EFI Install the black terminal ring to the ground block on the machine (Figure 22). Machines Install the red power wire into an empty slot on Install the new fuse block as follows: the machine fuse block (Figure 22).
- Page 15 Product Overview Controls Control Panel Windshield-Wiper Switch Click the switch forward to activate the windshield wipers (Figure 23). g026274 Figure 23 1. Windshield-wiper control 2. Light switch Light Switch Push the left or right side of the light plate to turn on the cab light (Figure 23).
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.