Page 1 Version 1.00 | 2021/01/20 User Manual JustConnect 16-Channel PoE Network Video Recorder DNR-4020-16P...
Page 2 Copyright © 2021 by D-Link Corporation, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation, Inc. Apple®, Apple logo®, iPhone®, iPad®, iPod touch® and Macintosh® are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Page 3: Table Of Contents
Network Status ..............53 OSD ..................25 PPPoE ..................54 Privacy Zone ..............26 Network Traffic ..............55 Microphone ..............27 System ....................56 Human Thermometer ...........28 Information ................56 Record .....................33 General ...................61 Record Schedule ..............33 User Account ................66 Disk ..................34 Security Center ..............68 D-Link DNR-4020-16P User Manual...
Page 4 Network Status ..............130 Privacy Zone ..............101 System ..................131 Microphone ..............102 Information ................ 131 Human Thermometer ..........103 System ................. 132 Record ..................108 User Account ..............137 Record Schedule .............. 108 Security Center ..............139 D-Link DNR-4020-16P User Manual...
Page 5 Maintenance ..............142 Auto Reboot ..............144 Password Reset ................. 145 Designate E-mail Address ..........145 Obtain Verification Code ..........146 Resetting User Password ..........147 Troubleshooting ..............148 Technical Specifications ............149 Regulatory Information ............152 D-Link DNR-4020-16P User Manual...
Page 6: Product Overview
Note: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller. D-Link DNR-4020-16P User Manual...
Page 7: System Requirements
• Two 3.5” SATA hard disk drives (not included) • Broadband Internet connection (for remote access) Network Requirements • Network camera(s) (refer to the D-Link website for a list of supported cameras) • 10/100/1000 Mbps Ethernet switch or router Web-based Configuration...
Page 8: Introduction
Rounding out the features is the JustConnect+ mobile app that lets administrators easily and remotely access and monitor the DNR-4020-16P on a mobile device — making the JustConnect H.265 PoE Network Video Recorder a complete, easy-to-use enterprise surveillance solution. D-Link DNR-4020-16P User Manual...
Page 9: Hardware Overview
Lights up when the device is receiving power and the power switch is turned on. HDD Indicator Hard disk status indicator. This indicator flashes when data is being transmitted. KB/Mouse Port USB port for a mouse or keyboard. Backup Port USB port for a flash drive. D-Link DNR-4020-16P User Manual...
Page 10: Rear Panel (Connections)
Connect a microphone to use 2-way communication with your camera(s). HDMI Output Output connector for an HDMI monitor. Alarm I/O Alarm I/O ports for connecting to sensors or other devices. Power Switch Press “1” to turn the device on, “0”to turn it off. D-Link DNR-4020-16P User Manual...
Page 11: Installation
1. First, make sure the power cable is not plugged into a power outlet. Remove the fixing screws from the top cover of the DNR-4020-16P, then remove the top cover from the device. 2. Insert two screws into the holes near the rear panel of the hard drive. Turn the screws twice, so that they protrude slightly. D-Link DNR-4020-16P User Manual...
Page 12 5. Re-attach the top cover by sliding it over the device. Re-insert the shorter screws in the rear and the longer screws in the sides of the cover to secure it. D-Link DNR-4020-16P User Manual...
Page 13: Setting Up Your Dnr-4020-16P (Hdmi / Vga)
You can set up your NVR without using a PC by connecting a VGA or HDMI display to the respective port on the back of the device. To control the Graphical User Interface (GUI), connect a USB mouse to the USB port on the front panel. D-Link DNR-4020-16P User Manual...
Page 14: Initial Configuration
3. In the Default channel password field, enter the password that will be used to view and configure the device’s channels. Click OK to continue. 4. On the next screen, reenter the admin password and click Login to access the management interface. D-Link DNR-4020-16P User Manual...
Page 15 • Network: Refer to page 44 • Date and Time: Refer to page 61 • Camera: Refer to page 12 • Disk: Refer to page 33 • Resolution: Refer to page 15 D-Link DNR-4020-16P User Manual...
Page 16: Live View
• Event List: Display a list of recent events, such as motion detection and triggered alarms • Stop Alarm: Stop an alarm that is currently in progress • Information: Display information about the DNR-4020-16P, such as its operational status and IP address D-Link DNR-4020-16P User Manual...
Page 17: Setup
The camera’s IP address. Model The camera’s model number. Protocol The protocol used to communicate with the camera. Firmware The firmware the specified camera is running. Version Operate Click this to set or update the camera’s settings. D-Link DNR-4020-16P User Manual...
Page 18 Enter the port used to connect to the camera. Username: Enter the username used to access the camera. Password: Enter the password associated with the username above. Remote Designate a channel for the camera’s display. Channel D-Link DNR-4020-16P User Manual...
Page 19: Rtsp Connection
Select the protocol type to use for the stream. This is set to RTSP by default. Port Select the RTSP port to use. This is set to 554 by default. Abs Path Enter the absolute path for the RTSP connection to use. D-Link DNR-4020-16P User Manual...
Page 20: Encode
Select the audio encoding format to use for the channel (e.g. Type G711A, G711U, etc). Resolution The resolution to use for the channel’s display. Frame Rate The frame rate at which to display the video. (fps) Bitrate Type Select the bitrate type (e.g. CBR, VBR, etc) D-Link DNR-4020-16P User Manual...
Page 21 Determine the quality of the stream from lowest to highest. Smart Encode Click to enable or disable smart encoding. If selected, this will configure some of the settings above automatically. Support for IP cameras is only available via private protocol. D-Link DNR-4020-16P User Manual...
Page 22: Sensor Settings
Select the type of scene (Indoor or Outdoor) or select Default. The default settings are determined by the IP camera’s video parameters. Brightness Adjust the image brightness. Sharpness Adjust the image sharpness. Contrast Adjust the contrast. Saturation Adjust the saturation. D-Link DNR-4020-16P User Manual...
Page 23 Select whether the scene is Indoors or Outdoors. Mirror From the drop-down, choose whether to display the scene normally or mirror it horizontally, vertically, or both. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 24 Shutter Priority, and Iris Priority (aperture priority). Meter Area Select the meter area. Max Shutter Select the maximum shutter speed. Max Gain Select the maximum gain. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 25 Select the mode from a variety of options, including Tungsten, Fluorescent, Daylight, Shadow, etc. If you select Manual, you will need to set the red and blue levels yourself. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 26 Auto, you will need to set the transition time between day and night modes, as well as the delay before the transition occurs. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 27 Enable or disable 2D and 3D noise reduction. Max Strength Select the maximum level of noise reduction to be applied to the image. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 28 (BLC). Defog Defog the image. Anti-shake Enable this to compensate for minor shaking of the camera, making the video smoother. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 29 Manually adjust the camera’s zoom. Focus Manually adjust the camera’s focus. Lens Click this to recalibrate the lens’s zoom and focus. initialization The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 30: Osd
Toggle this to display the current time on the selected channel’s OSD. Channel Toggle this to display the selected channel name on the OSD. Name The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 31: Privacy Zone
Click and drag a section of the screen to create a privacy zone. This area will not be viewable and will not be recorded. Double-click an existing privacy zone to delete it. Channel Select the channel to add a privacy zone to. The DNR-4020-16P supports up to four zones. D-Link DNR-4020-16P User Manual...
Page 32: Microphone
Channel Select the channel to configure the microphone for. Microphone Toggle this to enable or disable the microphone. Microphone Specify the type of microphone connection (e.g. Line In). Type Microphone Adjust the microphone volume/sensitivity. Volume D-Link DNR-4020-16P User Manual...
Page 33: Human Thermometer
DNR-4020-16P. Thermal Use this tab to set thermal mapping points on the camera’s display. Mapping Thermal Use this tab to calibrate the thermal camera with a separate calibration Calibration tool. D-Link DNR-4020-16P User Manual...
Page 34 Select the image matting quality from the drop-down. Matting Quality Snapshot Select the snapshot mode from the drop-down. Mode Upload Image Select the interval (from 1 to 10, in seconds) at which snapshots Interval should be uploaded. D-Link DNR-4020-16P User Manual...
Page 35 Toggle this to configure which parts of the image should be image uploaded via FTP at the interval entered above. matting/ whole image OSD Overlay Toggle this to overlay the time, date, channel, etc over the Snapshot snapshots D-Link DNR-4020-16P User Manual...
Page 36 Select the desired temperature area mode from the drop-down list. Area Temp. Select the desired measurement mode from the drop-down list. Measure Mode Normal Temp. Enter the normal temperature range. Values outside this range can be Range set to trigger an alarm. D-Link DNR-4020-16P User Manual...
Page 37 Full Screen: Display a full-screen notification on the attached monitor • Buzzer: Trigger a buzzer sound Schedule On this tab, you can click the calendar to set the thermometer to enable or disable according to a set schedule. D-Link DNR-4020-16P User Manual...
Page 38: Record
Click the bars on the right side of the screen to determine the recording type for the channel in question. The types are: • Continuous • Camera Alarm In • Motion Detection • NVR Alarm In D-Link DNR-4020-16P User Manual...
Page 39: Disk
The disk group that the specified hard drive belongs to. Recording Toggle this to allow new data to overwrite old data on the specified Overwrite hard drive. Expired Time Set the length of time (in days) after which old records will be (Day) automatically overwritten. D-Link DNR-4020-16P User Manual...
Page 40: Storage Mode
Use this page to configure the recording storage settings for hard drives and disk groups. Mode Select a storage mode. Selection Disk Group Select a disk group to configure. Channel Select a channel to assign to the selected disk group. D-Link DNR-4020-16P User Manual...
Page 41 In the box at the bottom of the page, you can view various attributes for the specified disk, such as the power cycle count. If no serious issues are detected, the attribute will display Good in the Status column. D-Link DNR-4020-16P User Manual...
Page 42: Disk Calculation
Select an amount of time or an amount of storage, depending on save time / whether Computation time or Computing Capacity was selected Disk Capacity above. Recording Enter the number of hours that NVR will record data (per day). time per day D-Link DNR-4020-16P User Manual...
Page 43: Ftp
Enter the password associated with the username entered above. FTP Path Enter the path to the directory where you would like to save your files. File Size (0-64 Enter the desired file size of each recording. A smaller size means more frequent uploads. D-Link DNR-4020-16P User Manual...
Page 44: Alarm
In this tab you can enable and configure the NVR’s general alarm. Duration Time Enter the duration that the alarm should activate for. Buzzer duration Enter the duration that the alarm buzzer should sound for. time D-Link DNR-4020-16P User Manual...
Page 45: Motion Detection
Alarm Out Enable Event Toggle to keep a record of alarm events. Recording Detection Select the area of the display to scan for motion. Area Detection Enable or disable the alarm according to a particular schedule. Schedule D-Link DNR-4020-16P User Manual...
Page 46: Video Loss
Popup Message: Display a notification in a popup window Enable Alarm Trigger a notification on the Alarm Out interface(s). Enable Event Toggle to keep a record of alarm events. Recording Detection Enable or disable the alarm according to a particular schedule. Schedule D-Link DNR-4020-16P User Manual...
Page 47: Alarm In
Specify the normal state of the sensor. A change from this state will trigger the alarm. Port Name Designate a name for the sensor. Camera Alarm Click this tab to configure similar settings for sensors connected to a camera’s Alarm In interface. D-Link DNR-4020-16P User Manual...
Page 48: Abnormal Alarm
Select the event(s) the alarm should trigger from the following list: • Email: Send an email notification • Buzzer: Trigger a buzzer sound • Popup Message: Display a notification in a popup window Enable Alarm Trigger a notification on the Alarm Out interface(s). D-Link DNR-4020-16P User Manual...
Page 49: Alarm Out
Action After Select either Close or Open. Receiving Trigger Alarm Output Select the alarm out put mode (Switch Mode by default). Mode Camera Alarm Configure similar settings for devices connected to a camera’s alarm out interface. D-Link DNR-4020-16P User Manual...
Page 50: Network
Obtain DNS Toggle this to enable DNS automatically. Automatically Preferred DNS Primary domain name server that translates names to IP addresses. Server Alternate DNS Secondary domain name server to back up the primary domain Server name server D-Link DNR-4020-16P User Manual...
Page 51 The HTTP port for the web UI. Data Port The port that data will be transferred over. The port that client devices will connect to. Client Port It is necessary to reboot the device after modifying any of the port configuration settings. D-Link DNR-4020-16P User Manual...
Page 52 Set this to match the subnet mask of the provided IP address. The default value is 255.255.255.0. Default Set this to the default gateway on your router or local subnet Gateway for proper network routing. The default gateway is 10.10.10.1. D-Link DNR-4020-16P User Manual...
Page 53: Ddns
Enter your host name. For example: myhost.mydomain.net. Username Enter the username for your dynamic DNS account. Password Enter the password for your dynamic DNS account. Confirm it in the next text box. Test Click this to test the DDNS settings. D-Link DNR-4020-16P User Manual...
Page 54: Port Mapping
Toggle this to enable or disable port mapping. If you enable this, you will also have to select a mode (Manual or Auto) and HTTP, client and data ports. NAT Port In this tab you can enter a start and end port for the NAT port range. D-Link DNR-4020-16P User Manual...
Page 55: Email
Enter the emails that should receive the NVR’s alerts. Enter the form of encryption to use, or select OFF. Encryption Sending Enter an internal between 0 and 600 seconds. interval Test Click this to send a test email. D-Link DNR-4020-16P User Manual...
Page 56: Ip Filter
IP Filter Toggle this to enable IP filtering. Rule Type Select Black List to block all IPs from the ranges you specify, or White List to only allow IPs from the ranges you specify. D-Link DNR-4020-16P User Manual...
Page 57: Snmp
SNMPV3 This SNMP version adds encryption and authentication to the service for better security. You can specify separate Read/Write versus Read-only name and passwords as well as the type of encryption to use. D-Link DNR-4020-16P User Manual...
Page 58: Network Status
Section 3 - Configuration Network Status On this page you can view the status of the NVR’s LAN and PoE ports and check your Internet connection. D-Link DNR-4020-16P User Manual...
Page 59: Pppoe
Username Enter the username provided by your ISP. Password IP Enter the password provided by your ISP. Address Enter the fixed address of the NVR and the port that is used to access the web interface. D-Link DNR-4020-16P User Manual...
Page 60: Network Traffic
Section 3 - Configuration Network Traffic This page displays the traffic being sent and received on the NVR’s various network interfaces, and information (such as MAC addresses). D-Link DNR-4020-16P User Manual...
Page 61: System
The number of channels supported by the device. Supported Alarm In The number of Alarm In interfaces. Alarm Out The number of Alarm Out interfaces. Audio In The number of Audio In interfaces. Audio Out The number of Audio Out interfaces D-Link DNR-4020-16P User Manual...
Page 62 Displays the IP address of the backup DNS server, if applicable. Server LAN Speed Displays the speed on the device’s LAN interface. Received Displays the total size of the received packets per second in Mb Packet D-Link DNR-4020-16P User Manual...
Page 63 Section 3 - Configuration Channel This page displays the name, online status, video format, resolution and bitrate of all of the DNR-4020-16P’s channels D-Link DNR-4020-16P User Manual...
Page 64 Section 3 - Configuration Disk On this page you can view information on the inserted hard drives, including their total capacity, the amount of space currently being used, and their operational status. D-Link DNR-4020-16P User Manual...
Page 65 Section 3 - Configuration Alarm On this page you can view information on the sensors and other devices connected to the DNR-4020-16P on its Alarm In and Alarm Out interfaces. D-Link DNR-4020-16P User Manual...
Page 66: General
Enter the a new name to identify the NVR to other devices. Display Port Enter the desired resolution for the NVR’s configuration Resolution interface. Language Select your preferred language. Temperature Select either Celsius or Fahrenheit. Units D-Link DNR-4020-16P User Manual...
Page 67 Specify how frequently (in seconds) to verify the system time Checks with the NTP server. Date If NTP Sync is disabled, automatically enter the date. Time If NTP Sync is disabled, automatically enter the current time. D-Link DNR-4020-16P User Manual...
Page 68 Section 3 - Configuration Time Zone On this page, you can select your current time zone and apply it to the NVR’s time settings. Time Zone Select your current time zone from the drop-down menu. D-Link DNR-4020-16P User Manual...
Page 69 Toggle this to enable or disable Daylight Saving Time. Savings Time Start Time The date and time that DST should start. End Time The date and time that DST should end. Offset Time The number of hours to adjust the clock during DST D-Link DNR-4020-16P User Manual...
Page 70 NVR’s. Sync Camera Toggle this to enable time syncing with the connected cameras. Time Frequency of Enter how often (in seconds) the NVR should sync its time Checks settings with its cameras’ time settings. D-Link DNR-4020-16P User Manual...
Page 71: User Account
On this page you can create or change the account information for the NVR’s user accounts (for example, by updating the password). Click the pencil icon under the Operate tab to edit an existing user account, or click Add to create a new one. D-Link DNR-4020-16P User Manual...
Page 72 Toggle this to set the device to log in automatically. Logout time Set the number of minutes of inactivity after which the device should log out automatically. Monitor channel(s) Select the channels to continue to monitor after logging out when logout from the device. D-Link DNR-4020-16P User Manual...
Page 73: Security Center
Use this tab to set a pattern to unlock your NVR instead of a Unlock Pattern typed password. Secure Email Use this tab to set a recovery email to use in case you forget your password D-Link DNR-4020-16P User Manual...
Page 74: Auto Sequence
Use the arrows at the bottom of the screen to cycle through the channels. Dwell Time Select the period of time (in seconds) to wait before displaying the next screen of channels. D-Link DNR-4020-16P User Manual...
Page 75: Auxiliary Sequence
Select the channel to display by default. Channel Enable Auto Toggle this to enable or disable auto sequencing on the auxiliary Sequence screen. If enabled, you may configure the auto sequence settings in the Auto Sequence tab. D-Link DNR-4020-16P User Manual...
Page 76: Logs
Enter the starting time to search the logs from. End Time Enter the end time to search the logs until. Search Click this to search for logs. Export Click this to export the logs to a file. D-Link DNR-4020-16P User Manual...
Page 77 Enter the starting time to search the logs from. End Time Enter the end time to search the logs until. Search Click this to search for logs. Export Click this to export the logs to a file. D-Link DNR-4020-16P User Manual...
Page 78: Maintenance
Reset the device to factory settings. Import Config. Import configuration settings from a file. Export Config. Export current configuration settings to a file. FW Update Update the device’s firmware. This requires a firmware file on an inserted USB storage device. D-Link DNR-4020-16P User Manual...
Page 79 Auto Check Enable or disable to auto check the latest firmware version with latest Version FOTA server. Auto Update Enable or disable to auto update device firmware. Setting hour, minute and the day for auto firmware update. D-Link DNR-4020-16P User Manual...
Page 80: Auto Reboot
Enable Auto Toggle this to enable the automatic restart feature. Reboot Reboot Time Set the frequency at which the device should restart (i.e. per day, week, or month) and the time that it should do so. D-Link DNR-4020-16P User Manual...
Page 81: Playback
Audio: Adjust the volume Start Backup: Begin a backup of the current recording Batch Backup: Create a backup of a batch of recordings (configured in a popup) Snapshot: Take a still snapshot of the current playback D-Link DNR-4020-16P User Manual...
Page 82: Picture Grid
Click a frame to view the playback for that time. Use the calendar in the left sidebar or the slider on the bottom of the screen to navigate to a different date. D-Link DNR-4020-16P User Manual...
Page 83: Event Recording
Select the channel and navigate to the date and time that you want to view events for using the sidebar. Check the boxes in the bottom left corner of the screen to search for a particular type of event. D-Link DNR-4020-16P User Manual...
Page 84: Backup List
Displays whether the backup came from the main or sub stream. Path The path to the backup file on the USB drive. Progress Indicates whether the backup is in progress or has finished. Operate Click the trash can to delete the backup. D-Link DNR-4020-16P User Manual...
Page 85: Setting Up Your Dnr-4020-16P (Web Gui)
You can set up your NVR via the web UI. To do this, connect an Ethernet cable to the LAN port on the rear panel of the device. Connect the other end of the cable to an Ethernet port on your switch, router, or computer. D-Link DNR-4020-16P User Manual...
Page 86 Alternatively, open a web browser and type the NVR’s IP address into the URL bar and press Enter. Or enter http://DNR-4020-16P-xxxx.local. in the address bar of your web browser (xxxx is the last four alphanumeric characters of the MAC ID on the device label). D-Link DNR-4020-16P User Manual...
Page 87: Initial Configuration
You will also be prompted to enter the default password to use to access cameras connected to the NVR. This password can also be set manually from the web UI for each camera. D-Link DNR-4020-16P User Manual...
Page 88: Live View / Home Screen
• Download: Download a backup of saved recordings • Logout: Sign off from the web UI • Help: Display the help menu On the bottom sidebar, click the buttons to determine how many channels should be displayed at one time. D-Link DNR-4020-16P User Manual...
Page 89 Open the shutter Close the shutter Focus on closer objects Focus on more distant objects Focus automatically Display more configuration options Switch between Scan and Tour modes Presets Select the number of points for the scan Edit D-Link DNR-4020-16P User Manual...
Page 90: Playback
Enter a time of day in the field and click Go. Recorded footage will be indicated by a blue bar on the bottom of the screen. You can click the bar at the desired time to view the recording. D-Link DNR-4020-16P User Manual...
Page 91: Alarm Search
On this page you can search the NVR’s alarm records for specific alarm types. Click the icon in the top right to select the channel(s), the type of alarm (e.g. video loss or motion detection) and dates/times to search. Click the tabs to view Channel Alarms or System Alarms. D-Link DNR-4020-16P User Manual...
Page 92: System
E (Explorer) Click the blue E icon to open a browser to view the camera in the web GUI. Click the ... icon to reboot or reset the IP camera (for cameras operating via private protocol only). D-Link DNR-4020-16P User Manual...
Page 93 Enter the port used to connect to the camera. Username: Enter the username used to access the camera. Password: Enter the password associated with the username above. Remote Designate a channel for the camera’s display. Channel D-Link DNR-4020-16P User Manual...
Page 94: Rtsp Connection
Select the protocol type to use for the stream. This is set to RTSP by default. Port Select the RTSP port to use. This is set to 554 by default. Abs Path Enter the absolute path for the RTSP connection to use. D-Link DNR-4020-16P User Manual...
Page 95: Encode
Select the audio encoding format to use for the channel (e.g. Type G711A, G711U, etc). Resolution The resolution to use for the channel’s display. Frame Rate The frame rate at which to display the video. (fps) Bitrate Type Select the bitrate type (e.g. CBR, VBR, etc) D-Link DNR-4020-16P User Manual...
Page 96 Higher bit rates result in higher video quality. Smart Encode Click to enable or disable smart encoding. If selected, this will configure some of the settings above automatically. Support for IP cameras is only available via private protocol. D-Link DNR-4020-16P User Manual...
Page 97: Sensor Settings
Select the type of scene (Indoor or Outdoor) or select Default. The default settings are determined by the IP camera’s video parameters. Brightness Adjust the image brightness. Sharpness Adjust the image sharpness. Contrast Adjust the contrast. Saturation Adjust the saturation. D-Link DNR-4020-16P User Manual...
Page 98 Select whether the scene is Indoors or Outdoors. Mirror From the drop-down, choose whether to display the scene normally or mirror it horizontally, vertically, or both. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 99 Shutter Priority, and Iris Priority (aperture priority). Meter Area Select the meter area. Max Shutter Select the maximum shutter speed. Max Gain Select the maximum gain. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 100 Select the mode from a variety of options, including Tungsten, Fluorescent, Daylight, Shadow, etc. If you select Manual, you will need to set the red and blue levels yourself. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 101 Auto, you will need to set the transition time between day and night modes, as well as the delay before the transition occurs. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 102 Enable or disable 2D and 3D noise reduction. Max Strength Select the maximum level of noise reduction to be applied to the image. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 103 (BLC). Defog Defog the image. Anti-shake Enable this to compensate for minor shaking of the camera, making the video smoother. The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 104 Manually adjust the camera’s zoom. Focus Manually adjust the camera’s focus. Lens Click this to recalibrate the lens’s zoom and focus. initialization The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 105: Osd
Toggle this to display the current time on the selected channel’s OSD. Channel Toggle this to display the selected channel name on the OSD. Name The configuration options on this page are only available for cameras being accessed via private protocol. D-Link DNR-4020-16P User Manual...
Page 106: Privacy Zone
Click and drag a section of the screen to create a privacy zone. This area will not be viewable and will not be recorded. Double-click an existing privacy zone to delete it. Channel Select the channel to add a privacy zone to. The DNR-4020-16P supports up to four zones. D-Link DNR-4020-16P User Manual...
Page 107: Microphone
Channel Select the channel to configure the microphone for. Microphone Toggle this to enable or disable the microphone. Microphone Specify the type of microphone connection (e.g. Line In). Type Microphone Adjust the microphone volume/sensitivity. Volume D-Link DNR-4020-16P User Manual...
Page 108: Human Thermometer
DNR-4020-16P. Thermal Use this tab to set thermal mapping points on the camera’s display. Mapping Thermal Use this tab to calibrate the thermal camera with a separate calibration Calibration tool. D-Link DNR-4020-16P User Manual...
Page 109 Select the image matting quality from the drop-down. Matting Quality Snapshot Select the snapshot mode from the drop-down. Mode Upload Image Select the interval (from 1 to 10, in seconds) at which snapshots Interval should be uploaded. D-Link DNR-4020-16P User Manual...
Page 110 Toggle this to configure which parts of the image should be image uploaded via FTP at the interval entered above. matting/ whole image OSD Overlay Toggle this to overlay the time, date, channel, etc over the Snapshot snapshots D-Link DNR-4020-16P User Manual...
Page 111 Select the desired temperature area mode from the drop-down list. Area Temp. Select the desired measurement mode from the drop-down list. Measure Mode Normal Temp. Enter the normal temperature range. Values outside this range can be Range set to trigger an alarm. D-Link DNR-4020-16P User Manual...
Page 112 Full Screen: Display a full-screen notification on the attached monitor • Buzzer: Trigger a buzzer sound Schedule On this tab, you can click the calendar to set the thermometer to enable or disable according to a set schedule. D-Link DNR-4020-16P User Manual...
Page 113: Record
Click the bars on the right side of the screen to determine the recording type for the channel in question. The types are: • Continuous • Camera Alarm In • Motion Detection • NVR Alarm In D-Link DNR-4020-16P User Manual...
Page 114: Disk
The disk group that the specified hard drive belongs to. Recording Toggle this to allow new data to overwrite old data on the specified Overwrite hard drive. Expired Time Set the length of time (in days) after which old records will be (Day) automatically overwritten. D-Link DNR-4020-16P User Manual...
Page 115: Storage Mode
Use this page to configure the recording storage settings for hard drives and disk groups. Mode Select a storage mode. Selection Disk Group Select a disk group to configure. Channel Select a channel to assign to the selected disk group. D-Link DNR-4020-16P User Manual...
Page 116: 111
In the box at the bottom of the page, you can view various attributes for the specified disk, such as the power cycle count. If no serious issues are detected, the attribute will display Good in the Status column. D-Link DNR-4020-16P User Manual...
Page 117: Disk Calculation
Select an amount of time or an amount of storage, depending on save time / whether Computation time or Computing Capacity was selected Disk Capacity above. Recording Enter the number of hours that NVR will record data (per day). time per day D-Link DNR-4020-16P User Manual...
Page 118: Ftp
Enter the password associated with the username entered above. FTP Path Enter the path to the directory where you would like to save your files. File Size (0-64 Enter the desired file size of each recording. A smaller size means more frequent uploads. D-Link DNR-4020-16P User Manual...
Page 119: Alarm
In this tab you can enable and configure the NVR’s general alarm. Duration Time Enter the duration that the alarm should activate for. Buzzer duration Enter the duration that the alarm buzzer should sound for. time D-Link DNR-4020-16P User Manual...
Page 120: Motion Detection
Alarm Out Enable Event Toggle to keep a record of alarm events. Recording Detection Select the area of the display to scan for motion. Area Detection Enable or disable the alarm according to a particular schedule. Schedule D-Link DNR-4020-16P User Manual...
Page 121: Video Loss
Popup Message: Display a notification in a popup window Enable Alarm Trigger a notification on the Alarm Out interface(s). Enable Event Toggle to keep a record of alarm events. Recording Detection Enable or disable the alarm according to a particular schedule. Schedule D-Link DNR-4020-16P User Manual...
Page 122: Alarm In
Specify the normal state of the sensor. A change from this state will trigger the alarm. Port Name Designate a name for the sensor. Camera Alarm Click this tab to configure similar settings for sensors connected to a camera’s Alarm In interface. D-Link DNR-4020-16P User Manual...
Page 123: Abnormal Alarm
Select the event(s) the alarm should trigger from the following list: • Email: Send an email notification • Buzzer: Trigger a buzzer sound • Popup Message: Display a notification in a popup window Enable Alarm Trigger a notification on the Alarm Out interface(s). D-Link DNR-4020-16P User Manual...
Page 124: Alarm Out
Action After Select either Close or Open. Receiving Trigger Alarm Output Select the alarm out put mode (Switch Mode by default). Mode Camera Alarm Configure similar settings for devices connected to a camera’s alarm out interface. D-Link DNR-4020-16P User Manual...
Page 125: Network
Obtain DNS Toggle this to enable DNS automatically. Automatically Preferred DNS Primary domain name server that translates names to IP addresses. Server Alternate DNS Secondary domain name server to back up the primary domain Server name server D-Link DNR-4020-16P User Manual...
Page 126 The HTTP port for the web UI. Data Port The port that data will be transferred over. The port that client devices will connect to. Client Port It is necessary to reboot the device after modifying any of the port configuration settings. D-Link DNR-4020-16P User Manual...
Page 127 Set this to match the subnet mask of the provided IP address. The default value is 255.255.255.0. Default Set this to the default gateway on your router or local subnet Gateway for proper network routing. The default gateway is 10.10.10.1. D-Link DNR-4020-16P User Manual...
Page 128: Ddns
Enter your host name. For example: myhost.mydomain.net. Username Enter the username for your dynamic DNS account. Password Enter the password for your dynamic DNS account. Confirm it in the next text box. Test Click this to test the DDNS settings. D-Link DNR-4020-16P User Manual...
Page 129: Port Mapping
Toggle this to enable or disable port mapping. If you enable this, you will also have to select a mode (Manual or Auto) and HTTP, client and data ports. NAT Port In this tab you can enter a start and end port for the NAT port range. D-Link DNR-4020-16P User Manual...
Page 130: Email
Enter the emails that should receive the NVR’s alerts. Enter the form of encryption to use, or select OFF. Encryption Sending Enter an internal between 0 and 600 seconds. interval Test Click this to send a test email. D-Link DNR-4020-16P User Manual...
Page 131: Ip Filter
IP Filter Toggle this to enable IP filtering. Rule Type Select Black List to block all IPs from the ranges you specify, or White List to only allow IPs from the ranges you specify. D-Link DNR-4020-16P User Manual...
Page 132: Snmp
SNMPV3 This SNMP version adds encryption and authentication to the service for better security. You can specify separate Read/Write versus Read-only name and passwords as well as the type of encryption to use. D-Link DNR-4020-16P User Manual...
Page 133: Web Mode
Section 3 - Configuration Web Mode Click the switch on this page to enable or disable HTTPS for the web UI. D-Link DNR-4020-16P User Manual...
Page 134: Pppoe
Username Enter the username provided by your ISP. Password IP Enter the password provided by your ISP. Address Enter the fixed address of the NVR and the port that is used to access the web interface. D-Link DNR-4020-16P User Manual...
Page 135: Network Status
Section 3 - Configuration Network Status On this page you can view the status of the NVR’s LAN and PoE ports and check your Internet connection. D-Link DNR-4020-16P User Manual...
Page 136: System
The number of channels supported by the device. Supported Alarm In The number of Alarm In interfaces. Alarm Out The number of Alarm Out interfaces. Audio In The number of Audio In interfaces. Audio Out The number of Audio Out interfaces D-Link DNR-4020-16P User Manual...
Page 137: System
Enter the a new name to identify the NVR to other devices. Display Port Enter the desired resolution for the NVR’s configuration Resolution interface. Language Select your preferred language. Temperature Select either Celsius or Fahrenheit. Units D-Link DNR-4020-16P User Manual...
Page 138 Specify how frequently (in seconds) to verify the system time Checks with the NTP server. Date If NTP Sync is disabled, automatically enter the date. Time If NTP Sync is disabled, automatically enter the current time. D-Link DNR-4020-16P User Manual...
Page 139 Section 3 - Configuration Time Zone On this page, you can select your current time zone and apply it to the NVR’s time settings. Time Zone Select your current time zone from the drop-down menu. D-Link DNR-4020-16P User Manual...
Page 140 Toggle this to enable or disable Daylight Saving Time. Savings Time Start Time The date and time that DST should start. End Time The date and time that DST should end. Offset Time The number of hours to adjust the clock during DST D-Link DNR-4020-16P User Manual...
Page 141 NVR’s. Sync Camera Toggle this to enable time syncing with the connected cameras. Time Frequency of Enter how often (in seconds) the NVR should sync its time Checks settings with its cameras’ time settings. D-Link DNR-4020-16P User Manual...
Page 142: User Account
On this page you can create or change the account information for the NVR’s user accounts (for example, by updating the password). Click the pencil icon under the Operate tab to edit an existing user account, or click Add to create a new one. D-Link DNR-4020-16P User Manual...
Page 143 Toggle this to set the device to log in automatically. Logout time Set the number of minutes of inactivity after which the device should log out automatically. Monitor channel(s) Select the channels to continue to monitor after logging out when logout from the device. D-Link DNR-4020-16P User Manual...
Page 144: Security Center
Use this tab to set a pattern to unlock your NVR instead of a Unlock Pattern typed password. Secure Email Use this tab to set a recovery email to use in case you forget your password D-Link DNR-4020-16P User Manual...
Page 145: Logs
Enter the starting time to search the logs from. End Time Enter the end time to search the logs until. Search Click this to search for logs. Export Click this to export the logs to a file. D-Link DNR-4020-16P User Manual...
Page 146 Enter the starting time to search the logs from. End Time Enter the end time to search the logs until. Search Click this to search for logs. Export Click this to export the logs to a file. D-Link DNR-4020-16P User Manual...
Page 147: Maintenance
Reset the device to factory settings. Import Config. Import configuration settings from a file. Export Config. Export current configuration settings to a file. FW Update Update the device’s firmware. This requires a firmware file on an inserted USB storage device. D-Link DNR-4020-16P User Manual...
Page 148 Auto Check Enable or disable to auto check the latest firmware version with latest Version FOTA server. Auto Update Enable or disable to auto update device firmware. Setting hour, minute and the day for auto firmware update. D-Link DNR-4020-16P User Manual...
Page 149: Auto Reboot
Enable Auto Toggle this to enable the automatic restart feature. Reboot Reboot Time Set the frequency at which the device should restart (i.e. per day, week, or month) and the time that it should do so. D-Link DNR-4020-16P User Manual...
Page 150: Password Reset
1. Log in to the NVR and right click the mouse to access the main menu. 2. Under System menu, select Security Center. 3. Go to Secure Email and input the administrator password and designate the Email Address. D-Link DNR-4020-16P User Manual...
Page 151: Obtain Verification Code
The NVR will generate a new verification code every day and after reboot. The NVR will need internect access to send out verification code e-mails. D-Link DNR-4020-16P User Manual...
Page 152: Resetting User Password
Input the new password in the New Password field and confirm the new password again in the Confirm Password field. Then click Modify Password to apply the new password. The new password can now be used to log into the NVR. D-Link DNR-4020-16P User Manual...
Page 153: Troubleshooting
Step 1: Open your web browser and connect to your NVR. Step 2: The browser will ask whether to install ActiveX. Step 3: Click the upper bar to begin the installation process. Step 4: Click Install to complete the process. D-Link DNR-4020-16P User Manual...
Page 154: Technical Specifications
• 1 x Fan Features Network Client OS • Microsoft Windows 10 Supported Cameras • Supports D-Link brand IP cameras • Supports auto-discovery Live View/Playback • HDMI port max output resolution: 4k • VGA port max output resolution: 1080p System Requirements for Web Interface •...
Page 155 • Console via HDMI/VGA Physical Weight • 2.8 kg (6.2 lbs) (No Disk) Power Input • Input: 100 to 240 V AC/ 3.0 A, 50 to 60 Hz • Output: 52 V AC/ 2.5 A, DC 12V/ 5.0A D-Link DNR-4020-16P User Manual...
Page 156 • Max. 143 W Temperature • Operating: 0 to 40 ˚C (32 to 104 ˚F) • Storage: -20 to 70 ˚C (-4 to 158 ˚F) Humidity • Max of 90% non-condensing Certifications • CE • RoHS • FCC Dimensions D-Link DNR-4020-16P User Manual...
Page 157: Regulatory Information
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. CE EMI Class A Warning This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. D-Link DNR-4020-16P User Manual...
Page 158 L’électricité statique peut endommager les composants électroniques. Déchargez l’électricité statique de votre corps (en touchant un objet en métal relié à la terre par exemple) avant de toucher le produit. • N’essayez pas d’intervenir sur le produit et ne le démontez jamais. Pour certains produits contenant une batterie remplaçable par l’utilisateur, D-Link DNR-4020-16P User Manual...
Page 159 • Mantenga el producto alejado de los radiadores y de otras fuentes de calor. • Desenchufe siempre el producto de la alimentación de red antes de limpiarlo y utilice solo un paño seco sin pelusa" D-Link DNR-4020-16P User Manual...
Page 160 • Houd het product uit de buurt van radiators en andere warmtebronnen. • U dient het product steeds los te koppelen van de stroom voordat u het reinigt en gebruik uitsluitend een droge pluisvrije doek" D-Link DNR-4020-16P User Manual...
Page 161 D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging. D-Link recommends that you always switch off or unplug your D-Link products when they are not in use. By doing so you will help to save energy and reduce CO2 emissions.
Page 162 D-Link et l’environnement Chez D-Link, nous sommes conscients de l'impact de nos opérations et produits sur l'environnement et nous engageons à le réduire. Pour limiter cet impact, D-Link conçoit et fabrique ses produits de manière aussi écologique que possible, en utilisant des matériaux recyclables et faiblement toxiques, tant dans ses produits que ses emballages.
Page 163 D-Link zijn producten zo milieuvriendelijk mogelijk, door het gebruik van recycleerbare producten met lage toxiciteit in product en verpakking. D-Link raadt aan om steeds uw D-Link producten uit te schakelen of uit de stekker te halen wanneer u ze niet gebruikt. Door dit te doen bespaart u energie en beperkt u de CO2-emissies.
Page 164 D-Link a životní prostředí Ve společnosti D-Link jsme si vědomi vlivu našich provozů a výrobků na životní prostředí a snažíme se o minimalizaci těchto vlivů. Proto své výrobky navrhujeme a vyrábíme tak, aby byly co nejekologičtější, a ve výrobcích i obalech používáme recyklovatelné a nízkotoxické materiály.
Page 165 D-Link produkter som er så miljøvennlig som mulig, ved å bruke resirkulerbare, lav-toksiske materialer både i produktene og forpakningen. D-Link anbefaler at du alltid slår av eller frakobler D-Link-produkter når de ikke er i bruk. Ved å gjøre dette hjelper du å spare energi og å redusere CO2-utslipp.
Page 166 D-Link sine produkter, så de er så miljøvenlige som muligt, ved at bruge genanvendelige materialer med lavt giftighedsniveau i både produkter og emballage. D-Link anbefaler, at du altid slukker eller frakobler dine D-Link-produkter, når de ikke er i brug. Ved at gøre det bidrager du til at spare energi og reducere CO2-udledningerne.
Page 167 D-Link och miljön På D-Link förstår vi och är fast beslutna att minska den påverkan våra verksamheter och produkter kan ha på miljön. För att minska denna påverkan utformar och bygger D-Link sina produkter för att de ska vara så miljövänliga som möjligt, genom att använda återvinningsbara material med låg gifthalt i både produkter och förpackningar.

D-Link JustConnect DNR-4020-16P User Manual

Product Overview

Installation

Troubleshooting

Technical Specifications

Regulatory Information

Quick Links

Related Manuals for D-Link JustConnect DNR-4020-16P

Summary of Contents for D-Link JustConnect DNR-4020-16P

Table of Contents