hit counter script
Toro 41250 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Garden Machinery Accessories
  5. 41250
  6. Installation instructions manual
Toro 41250 Installation Instructions Manual

Toro 41250 Installation Instructions Manual

Road light and homologation kit for multi pro 1750 turf sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Road Light and Homologation Kit
Multi Pro
Model No. 41250—Serial No. 314000001 and Up
This kit is designed to add the light components required for
on-road travel. It is a dedicated attachment for a turf spray
application vehicle and is intended to be used by professional,
hired operators in commercial applications.
Note: Determine the left and right sides of the machine
from the normal operating position.
Read these instructions carefully to learn how to operate
and maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe products,
you are responsible for operating the product properly and
safely.
You may contact Toro directly at www.Toro.com for product
and accessory information, help finding a dealer, or to register
your product.
Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
This product contains a chemical or chemicals known to the State of California to
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
1750 Turf Sprayer
WARNING
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Register at www.Toro.com.
Customer Service and have the model and serial numbers of
your product ready. Figure 1 illustrates the location of the
model and serial numbers on the product.
1. Model and serial number plate
Original Instructions (EN)
All Rights Reserved *3405-939* A
Printed in the USA
Form No. 3405-939 Rev A
Installation Instructions
Figure 1

Advertisement

Table of Contents
loading

Related Manuals for Toro 41250

Summary of Contents for Toro 41250

  • Page 1 Although Toro designs and produces safe products, you are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register Figure 1 your product.

  • Page 2: Installation

    Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. – No parts required Remove the seat. Headlight support Bolt (5/16 x 2-1/4 inch) Washer (5/16 inch) Flanged locknut (5/16 inch) Install the front and rear lights.
  • Page 3 Procedure Description Qty. Lock-mount bracket Latch Grip Install the seat lock. Hex-head screw (12 x 30 mm) Locknut (12 mm) – No parts required Install the seat.

  • Page 4: Preparing The Machine

    Preparing the Machine No Parts Required Procedure 1. Move the machine onto a level surface, set the parking Figure 3 brake, shut off the pump, shut off the engine, and 1. Nut 3. Terminal (positive-battery remove the ignition key. cable) 2.
  • Page 5 Figure 7 1. Seat plate 2. Seat Figure 5 1. Washer 3. Hairpin 4. Prop rod 2. Bracket (seat) 3. Remove the 2 hairpins that secure the pivot fitting of the seat plate to the chassis brackets (Figure Figure 6 1.
  • Page 6 Installing the Front and Rear Lights Parts needed for this procedure: Headlight support Bolt (5/16 x 2-1/4 inch) Washer (5/16 inch) Flanged locknut (5/16 inch) Figure 9 Headlight 1. Threaded post (headlight) 4. Vertical hole (front-light Rear-light bracket (left) support) Rear-light bracket (right) 2.
  • Page 7 Installing the Rear Lights 6. Repeat steps at the other rear-light bracket at the other end of the center-boom channel. 1. Align the holes of the rear-light bracket with the 2 holes in the center-boom channel. Note: The left and right rear-light bracket are unique. Ensure that the short flange of the bracket is flush with the surface of the channel.
  • Page 8 3. Remove the backing from a speed decal. 4. Align the top and forward edges of the sprayer decal (B of Figure 12) with the tape marks that you made in steps and 1. 5. Press the decal onto the surface of the tank from the top down while removing air bubbles as you apply the decal.
  • Page 9 Installing the License Plate Brackets 1. Assemble the license-plate bracket to the support bracket with the 2 flange-head bolts (5/16 x 3/4 inch) and 2 flange locknuts (5/16 inch) as shown in Figure Figure 15 1. Flange-head bolts (5/16 x 3.
  • Page 10 2. Align the data plate to the platform channel as shown Figure 17 and mark the 4 hole locations. 3. Centerpunch the platform channel at the 4 marks (Figure 17). Installing the Data Plate 4. Drill 4 holes 3 mm (1/8 inch) through the channel at the centerpunch marks (Figure 17).
  • Page 11 2. Rotate the 90° bracket as shown in Figure 20 loosely secure it to the mounting stud of the horn assembly with the nut that you removed in step 1. Note: You will tighten the nut of the horn assemble in a later procedure.
  • Page 12 Installing the Main-Block Fuse Insert the fuse into the main-block frame (Figure 23). Installing the Flasher Module and the Main-Block Fuse Parts needed for this procedure: Flasher module Push-in fastener Fuse (15 A) Figure 23 Installing the Flasher Module 1. Fuse (15 A) 2.
  • Page 13 Routing and Installing the Wire Harness to the Machine Parts needed for this procedure: Wire harness Cable tie Preparing to Route the Wire Harness Use the following graphic for an outline of routing the wire harness to the machine (Figure 24).
  • Page 14 Routing the Wire Harness to the Side Console 1. Route the harness through the front of the seat shroud (Figure 25). Figure 27 1. Ring terminal 2. Positive (+) battery post Routing the Wire Harness to the Figure 25 Turn-Signal 1.
  • Page 15 Figure 31 1. Horn 3. Terminal of the wire-harness leg 2. Terminal of the horn 3. Tighten by hand the nut that secures the horn to the Figure 29 90° bracket; refer to Figure 20 7 Installing the Horn 1. Turn-signal switch 2.
  • Page 16 Routing the Wire Harness to the Taillights 1. Route the tail light leg of the wire harness from the flasher module rearward along the right-frame tube between the frame tube and the engine (Figure 35). Figure 33 1. 6-socket connector 3.
  • Page 17 Figure 39 1. Tail light 3. 4-pin connector 2. 4-socket connector 7. Repeat step for the other tail light. Figure 37 1. Wire harness 3. 4-socket connector ( LEFT REAR TURN BRAKE SIGNAL 2. Boom-valve bracket Installing the License-Plate 4. Route the wire harness to the left of the flow meter and toward the boom-frame channel (Figure 38).
  • Page 18 2. Align the lens for the light down and the holes in the light with the holes in the license-plate bracket (Figure 41). Figure 42 1. Hole plug 2. Side-console mount 2. Route the 8-socket connector of the wire harness through the hole in the side-console mount (Figure 43).
  • Page 19 Installing the Light Switch and the Horn Button Parts needed for this procedure: Horn switch Button cover Figure 46 3-position switch 1. Control-panel cover 2. Choke control Light-switch decal (plain) 4. Remove the round plug from the control-panel cover Installing the Horn Switch (A of Figure 47).
  • Page 20 Figure 48 1. Horn switch 2. 2-pin connector Installing the Light Switch Figure 50 1. Remove the existing 8-socket connector from the old 1. Socket connector 2. Light-switch connector light switch (Figure 49). (slot number 1) 4. Install the light-switch decal onto the control-panel cover, centered over the light switch opening, with the words toward the back of the machine...

  • Page 21: Connecting The Battery

    Connecting the Battery No Parts Required Procedure Figure 52 1. Align the ring terminal for the machine wire harness, ring terminal of the kit wire harness, terminal for 1. 3-position switch 2. 8-socket connector (with the positive battery cable to the positive battery post the line in slot number 1) (Figure 54).
  • Page 22 4. Align the lock bracket and the clevis pin through the hole of the outboard-seat gusset (Figure 56). 5. Align the holes in the latch with the holes in the seat gussets (Figure 57). Installing the Seat Lock Parts needed for this procedure: Lock-mount bracket Latch Grip...

  • Page 23: Installing The Seat

    8. Fully insert the clevis pin through the holes in the seat latch and the inboard-seat gusset. 9. Secure the lock bracket to the outboard-seat gusset with the hex-head screw (12 x 20 mm) and the locknut (12 mm) as shown in Figure Figure 62 1.

  • Page 24: Operation

    Operation 7. With seat latched, ensure that the grip of the lock-mount bracket is facing down. Using the Headlights Move the light switch on the side console rearward toward the sloped end of the switch to turn the headlights to the position (Figure 65).

  • Page 25: Maintenance

    Using the Horn Maintenance Push down on the horn button to sound the horn (Figure 67). Replacing Light Bulbs Replacing a Headlight Bulb 1. Ensure that the light switch is in the O position. 2. Remove the 6 screws securing the headlight (Figure 69).
  • Page 26 Replacing a Tail-light Bulb Replacing a License Plate Bulb 1. Ensure that the light switch is in the O position. 1. Remove the 2 screws that secure the cover to the base of the license-plate light, and remove the cover (A of 2.

  • Page 27: Replacing Fuses

    Replacing Fuses Replacing Fuse Block Fuse The electrical system is protected by fuses, and requires no maintenance. If a fuse blows, check the component or circuit for a malfunction or short. 1. Pull out the open fuse. 2. Replace the open fuse with a new fuse (Figure 72).
  • Page 28 Notes:...
  • Page 29 Notes:...
  • Page 30 Notes:...
  • Page 31 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
  • Page 32 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.

Table of Contents