Fm/Am Tuning; Tuning In To The Desired Fm/Am Station (Frequency Tuning); Registering Fm/Am Stations And Tuning In (Preset Tuning) - Yamaha RX V565 Owner's Manual
Av receiver
Hide thumbs
Also See for RX V565:
- Service manual (150 pages) ,
- Owner's manual (136 pages) ,
- Firmware update procedures (5 pages)
Table of Contents
Advertisement
The FM/AM tuner of this unit provides the following two
modes for tuning.
■
Frequency tuning mode (Auto tuning /
Manual tuning)
You can tune in to a desired FM/AM station by searching
or specifying its frequency.
■
Preset tuning mode (Preset tuning)
You can preset the frequencies of FM/AM stations by
registering them to specific numbers, and later just select
those numbers to tune in.
Note
• Adjust the FM/AM antennas connected to this unit for the best reception.
Tuning in to the desired FM/AM station
(Frequency tuning)
1
Press NINPUT l / h (or gTUNER)
repeatedly and switch the input source to
"TUNER."
2
Press FFM (hFM) or GAM (hAM) to select
a band.
"FM" or "AM" appears on the front panel display
according to the band that you have selected.
3
Press HTUNING l / h (or hTUNING k /
n) to specify the frequency.
To adjust the frequency to a higher range, press h (or
k). To adjust it to the lower range, press l (or n).
The TUNED indicator on the front panel display
lights up when the tuner is tuned in to a station. The
STEREO indicator also lights up if the program being
broadcasted is in stereo.
FM 92.5 MHz
The frequency changes in the following manner according
to how you press HTUNING l / h (or hTUNING k
/ n).
When you press the key more than 1 second
The tuner searches the frequency of a station that is
detectable around the current frequency. This is effective
when the tuner can receive strong signals without any
interference. Once the search starts, release the key.
When you keep holding the key, the search continues even
when a station is detected. This is useful when you want to
tune in to a specific station.
When you press and release the key
The tuner increases or decreases the frequency in steps.
Use this method when the tuner cannot receive strong
signals and stations are skipped during the search. You can
listen to better quality sound even when the tuner cannot
receive a strong signal.
28
En
FM/AM tuning
STEREO
TUNED
y
• You can switch between stereo and monaural for FM broadcast in the
option menu (see page 34).
4
To tune in by direct frequency tuning, enter
the frequency of the desired station using
the numeric keys on the remote control.
Enter only integers. For example, if you want to set
the frequency to 88.9 MHz, enter "889" using
sNumeric keys.
Note
• "Wrong Station!" appears on the front panel display when you
enter a frequency that is out of receivable range. Make sure that the
entered frequency is correct.
Registering FM/AM stations and
tuning in (Preset tuning)
You can register up to 40 FM/AM stations (Preset) using
"Automatic station preset" or "Manual station preset."
Registering stations by automatic station
preset
The tuner automatically detects FM stations with strong
signals and registers up to 40 stations. AM stations cannot
be automatically registered. Use manual station preset.
1
Press NINPUT l / h repeatedly (or press
gTUNER) to switch the input source to
"TUNER."
2
Press mOPTION on the remote control.
The option menu screen for setting options of tuner
input appears on the front panel display.
y
• For details on the option menu, see page 33.
• The option menu is displayed on monitor components.
3
Select "Auto Preset," and press nENTER.
Auto Preset
Automatic station preset starts about 5 seconds later
from the lowest frequency upwards.
y
• You can select the preset number at which the preset starts by
pressing hPRESET k / n or nCursor k / n while the front
panel display is in the state as shown in the below figure.
• To cancel registration, press nRETURN on the remote control.
Status
01:FM 87.5 MHz
Preset number
Frequency
Hide quick links:
Advertisement
Chapters
Table of Contents
