Advertisement
Available languages
Available languages
Quick Links
Condenser
Operating Instructions
Microphone
Mode d'emploi
C-100
©2018 Sony Corporation Printed in Japan
http://www.sony.net/
4-735-085-12(1)
1
GB
FR
3
English
Before using the microphone, please read this manual thoroughly. This manual should be
retained for future reference.
FOR UNITED STATES CUSTOMERS. NOT APPLICABLE IN CANADA, INCLUDING IN THE
PROVINCE OF QUEBEC.
POUR LES CONSOMMATEURS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y
COMPRIS LA PROVINCE DE QUÉBEC.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
The validity of the CE marking is restricted to only those countries where it is legally
enforced, mainly in the countries EEA (European Economic Area).
Names and Functions of Parts (Fig.)
(The numbers refer to the corresponding numbers in the figure.)
Microphone
Directivity (Polar pattern) switch
: Uni-directional
: Omni-directional
: Bi-directional
PAD switch
Select the PAD switch to the level of input source.
:
Off
: On
LOW CUT switch
The low cut filter reduces the wind noise effectively.
: Normal setting
: The low cut filter is applied.
Output connector (XLR-3-12C type)
The sound recorded with the microphone is output. The power is supplied to the
microphone from an external equipment through this connector when the microphone
is operating on the external power supply.
Wind screen
Attach to the microphone to reduce wind or breathing noise.
Cradle suspension
When using a microphone stand (not supplied), for example, attach the cradle
suspension to the microphone.
A stand adaptor is equipped to the cradle suspension. If you do not plan on using the
stand adaptor, detach it, and then attach it to a microphone stand (sold separately).
Ring
Be sure to rotate and fix the ring after the microphone is equipped to the cradle
suspension. Unless done so, there is a risk the microphone will fall.
Stand adaptor
Power Supply
This microphone is powered only from an external power supply. Connect output connector
of the microphone to the microphone connector of a Phantom power supply (external
power supply) or an audio mixer. For connection, use a microphone cable.
Note
An unbalanced cable cannot be connected to this microphone. Be sure to use a balanced
microphone cable.
How to open the carrying case (Fig.)
1 Pull up the bottom hinge.*
2 Pull down the upper hinge.*
* Release the other hinge in the same way.
3 Push up the lid.
• When closing the carrying case, be careful that your hands, etc. are not caught in it.
• Do not place a heavy object or sit on the carrying case.
2
Condenser Microphone
Notes on Use
• Microphones are delicate. Do not drop or subject it to excessive shock.
• Avoid extended usage or storage in high humidity or temperatures above 60 °C (140 °F).
It may cause noise or failure.
• If acoustic feedback occurs during use (a howling sound is heard from the speakers),
point the microphone away from the speakers or increase the distance between the
microphone and the speakers.
• It takes a few minutes for the output voltage to stabilize after changing the directivity
switch.
Use it after the output is stabilized.
• The microphone output signal is a balanced output. Unbalanced output is not supported,
so be sure to connect it to the balanced input circuit.
• Since the microphone adopts an extremely high impedance circuit, if the switch is
changed while the external power is on, it may emit induction noise, but this is not a
malfunction.
• The portion with "AUTO_PRESSURE_RELEASE" on the carrying case cannot be moved.
Also, this does not guarantee its performance.
• A cable with the connector housing part connected to the ground wire (pin 1) is
recommended for the microphone cable.
Cables that are not connected to a ground wire may emit noise.
If a ground terminal is available, noise can be reduced by connecting to that terminal.
Also, if used extending several microphone cables and the connector housing part
touches the floor, noise may worsen.
Specifications
General
Type
2 Way Microphone (Condenser + Electret condenser)
Power supply
External power supply operation 44 V to 52 V DC (IEC* 61938 P48)
Power consumption
Less than 4.5 mA
Output connector
XLR-3-12C Type
Dimensions
40 mm dia. × 175 mm (1.57 in. dia. × 6.89 in.)
Mass
Approx. 290 g (10.2 oz)
Supplied accessories
Cradle suspension (1)
Wind screen (1)
Stand adaptor (W3/8 - NS5/8) (1)
Carrying case (1)
Operating instructions (this sheet) (1)
Warranty card (1)
Performance
Frequency response
20 Hz - 50,000 Hz
Directivity
Uni-directional / Omni-directional / Bi-directional (switchable)
Output impedance
90 Ω ±15%, balanced
Sensitivity
-31 dB (Uni-directional)
-37 dB (Omni-directional)
-35 dB (Bi-directional)
(deviation±3 dB)
(0 dB=1 V/Pa, 1 kHz)
Inherent noise
Less than 19 dB SPL (Uni-directional)
Less than 24 dB SPL (Omni-directional)
Less than 22 dB SPL (Bi-directional)
(0 dB=2 × 10
-5
Pa)
(IEC* 61672-1 A-Weighted, 1 kHz, 1 Pa)
Maximum input sound pressure level
More than 132 dB SPL (Uni-directional)
More than 138 dB SPL (Omni-directional)
More than 136 dB SPL (Bi-directional)
(output level for 1% waveform distortion at 1 kHz, converted into
equivalent input sound pressure level: 0 dB=2 × 10
Dynamic range
More than 113 dB (Uni-directional)
More than 114 dB (Omni-directional)
More than 114 dB (Bi-directional)
PAD
0 dB/-10 dB (switchable)
LOW CUT filter
Flat/70 Hz (switchable)
* IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Note
Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE
FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE
TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION
OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.
-5
Pa)
Advertisement
Related Manuals for Sony C-100
Summary of Contents for Sony C-100
- Page 1 Note stand adaptor, detach it, and then attach it to a microphone stand (sold separately). Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR ...
- Page 2 La conception et les spécifications peuvent être modifiées sans préavis. Remarque Vérifiez toujours que l’appareil fonctionne correctement avant l’utilisation. Sony n’assumera pas de responsabilité pour les dommages de quelque sorte qu’ils soient, incluant mais ne se limitant pas à la compensation ou au remboursement, à cause de la perte de profits actuels ou futurs suite à...