hit counter script
Download
Share
Print this page
Honeywell ImperLED E Quick Start Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Lantern
  5. ImperLED E
  6. Quick start manual
Honeywell ImperLED E Quick Start Manual

Honeywell ImperLED E Quick Start Manual

Hide thumbs Also See for ImperLED E:
1
2
3
4
5
6
7
8
9

Advertisement

Available languages

Available languages

Quick Links

Download this manual
Dimensional drawings:
Installation:
1
4
Mounting methods
ImperLED E luminaries can be surface mounted on walls or ceilings. For these mounted installations, special
accessories are included. A recessed kit is also available.
Step 1: Place a flat blade screwdriver and pull up gently the 6 diffusor clips from both sides to remove the
diffusor.
Step 2: Place a flat blade screwdriver and pull up gently the reflector.
Step 3: Install the plastic base with the included mounting screws and plugs. If the hole that exists is not useful,
drill another hole on one of the designated positions in order to pass the cables and install the included
gasket (verify that it is not deformed).
Step 4: Always use in any case round cable, with a diameter of 5-10mm (H05RN-F type 2x1mm
type, at least equal to its mechanical and electrical properties). ATTENTION! The cable must not be
deformed in any way (this requirement is important to ensure the IP rating).
Make a hole in the center by using a small screwdriver. Pass the round cable through the gasket.
Step 5: Connect the mains cable to the respective terminal block: L for live wire, N for neutral. Power supply
cables cross section should be 0.8 – 3 mm
(optional), DALI communication (optional) or voltage-free contact (optional).
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway
ImperLED E
2
5
. The C1 and C2 terminals are used for elBus communication
2
3
or any other
2
http://www.hls-nordic.com
GB

Advertisement

loading

Related Manuals for Honeywell ImperLED E

Summary of Contents for Honeywell ImperLED E

  • Page 1 Installation: Mounting methods ImperLED E luminaries can be surface mounted on walls or ceilings. For these mounted installations, special accessories are included. A recessed kit is also available. Step 1: Place a flat blade screwdriver and pull up gently the 6 diffusor clips from both sides to remove the diffusor.
  • Page 2 Step 6: The control of maintained or non-maintained operation of the luminary is achieved through Switch 4 on DS1. For maintained operation, switch number 4 must be in ON position. For non-maintained operation, switch number 4 must be in OFF position. Step 7: Install the included cable tie (if needed) to fasten securely the power cables.

  • Page 3: Selftest Functions

    Expected battery lifetime 10 years At the end of their useful life the packaging, product and batteries The ImperLED E is a self-contained luminaire with selftest function. should be disposed of via a It can be configured as maintained or non-maintained.
  • Page 4 ImperLED E Målskisse: Installasjon: Monteringsmetode: ImperLED E kan monteres på vegg eller tak, monteringsutstyr medfølger. Innfellingssett er tilgjengelig som tilleggsutstyr. Pkt. 1: Bruk en flatspor skrutrekker til forsiktig å trekke opp de 6 låseklipsene på lampedekslet. Ta av lampedekslet. Pkt. 2: Bruk en flatspor skrutrekker og trekk reflektoren forsiktig opp.
  • Page 5 Merk: Dersom batteriet skal skiftes ut, må det erstattes av samme type og kapasitet. Batteribytte må utføres av leverandør eller kvalifisert person. Merk: Lyskilden er ikke utskiftbar. Merk: Dersom armaturens nettkabel er skadet, må den kun skiftes ut av kompetent person for å unngå fare. Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com...
  • Page 6 Teknisk beskrivelse ImperLED E Combi ST LED 230V 1h wPict 10y Indikatordioder Beskrivelse Artikkelnr.: 290406.10 Lumenutbytte, normal: 250 lm Lumenutbytte, nøddrift: 350 lm Vekt: 880 g Maks. effektforbruk: 5.4W / 5.6VA Normal Driftsspenning: 220-240V AC / 50-60Hz Varighet nøddrift: Minimum 1 time...

  • Page 7: Installation

    ImperLED E Måttskiss: Installation: Monteringsmetoder ImperLED E-armaturer kan monteras på vägg eller i tak. Nödvändiga tillbehör ingår. Infällnads-kit beställs separat. Steg 1: Använd en platt skruvmejsel för att försiktigt dra upp de 6 låsklämmorna på lampskyddet. Ta bort lampskyddet. Steg 2: Använd en platt skruvmejsel och dra försiktigt upp reflektorn.
  • Page 8 Nödbelysning Vägledande markering Steg 6: Val av nöd- eller vägledande markering görs med DIP- switch 4 på DS1. För vägledande markering måste switch # 4 vara inställd på position ON. För nödbelysning måste switch # 4 ställas i OFF-läge. Steg 7: De medföljande stripsen kan användas för avlastning av kabeln. Steg 8: Anslut batteriet till motsvarande kontakt på...
  • Page 9 Teknisk beskrivning ImperLED E Combi ST LED 230V 1h wPict 10y Indikeringsdioder Beskrivning Art no.: 290406.10 Lumen, normaldrift: 250 lm Lumen, nöddrift: 350 lm Vikt: 880 g Max. effektförbrukning: 5.4W / 5.6VA Normal drift Driftspänning: 220-240V AC / 50-60Hz Nöddrifttid: Minimum 1 timma Laddning pågår (batteritest inte möjligt under laddning)