Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when building this shed.
‰
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the shed for any purpose other than that for which it is designed.
8
Use appropriate safety clothing including eye protection.
9
DO NOT attempt to assemble in windy weather.
8
Note: The assembly of this product will require assistance.
2. INTRODUCTION
Galvanized steel panels easily assembled to form a rigid and secure gable roofed shed. Has a single door which is secured by cross bolt and
eyelet that accepts a padlock (not included) for additional security. Supplied with bolt-down fixing kits.
3. SPECIFICATION
Model no's: ...........................................GSS2323/GSS2323G
Colour: .................................................................silver/green
Roof type:....................................................................... apex
Doors: .................................................................................. 1
Overall size (W x D x H*): ................. 2300 x 2300 x 1900mm
* minimum wall height
4. CONCRETE PLINTH
Concrete slab: Please ensure that your site is level. It is recommended that your slab is 100mm thick and you use builders plastic and F52
reinforcing mesh. We recommend that you make your slab 100mm bigger than the base dimensions of your shed. This will allow for a 50mm
edge around your shed. We recommend that you slope the 50mm edges downward by 10 mm so that rain water will drain away from your shed.
© Jack Sealey Limited
INSTRUCTIONS FOR
GALVANIZED SHED 2.3 X 2.3 X 1.9M
MODEL NO:
Wear safety
Wear
footwear
gloves
Original Language Version
GSS2323 & GSS2323G
GSS2323/G | Issue:2(SP) 13/04/17
Advertisement
Related Manuals for Sealey GSS2323
Summary of Contents for Sealey GSS2323
- Page 1 GSS2323 & GSS2323G MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Sheet Sheet 1216x770 Roof Sheet Sheet 2000x735 Front Sheet Sheet 2000x735 Front Door Sheet Sheet 1945x770 Door Channel Channel 1943 Door Channel Channel 1943 Door Channel Channel 768 Door Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 3 Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 4 Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 5 Signature: _________________________________________ In the unlikely event that you find you are missing a part, please contact Pinnacle at 1800 349 776. A copy of proof of purchase may be requested. Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 6 GardenShed 2.3 x 2.3 x 2.4m Shed overview: Shed overview: Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 7 Tip: If panel and screw holes do not line up, try pulling panel to match up holes. Tip: If panel and screw holes do not line up, try pulling panel to match up holes. Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 8 26H are used as top side channels. Make sure part 26I and 26H are used as top side channels. ROOF TOP EDGE RIDGES FACING UP ROOF TOP EDGE RIDGES FACING UP Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 9 RIDGES FACING DOWN ROOF TOP EDGE Note: Channel 34R and 34L Note: Channel 34R and 34L should face down. should face down. Mid wall channel Mid wal lchannel connector connector Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 10 NOTE: Screws are applied to both sides of the connectors. All screws marked with a cross should not be fixed at this stage. ROOF TOP EDGE RIDGES FACING UP Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 11 Repeat the same steps for the other side. NOTE: All screws marked with a cross should not be fixed at this stage. Make sure the small lip on the channel is always facing out. This ensures rain water cannot build up inside your shed. RIDGES FACING DOWN ROOF TOP EDGE Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 12 Enhance the structural strength by applying part 66 (channel connector). Note that screws are applied to both sides of the connectors. Enhance the structural strength by applying part 66 (channel connector). Note that screws are applied to both sides of the connectors. Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 13 Leave 4 corners unfixed at this stage. Repeat the same steps for the other roof panel. Leave 4 corners unfixed in this stage. Repeat the same steps for the other roof panel. Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 14 (channel connector). Fix parts 26P , 26N (top channels), 42A (jamb), 26L, 26M, and 23A (bottom channels) with self-tapping screws. Enhance the top channels by applying part 66 (channel connector). Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 15 Now fix parts 33R and 33L (mid wall channels) to the sheeting with self tapping screws. Note: The groove should face downwards. Now fix parts 33R and 33L (mid wall channels) to the sheeting with self-tapping screws. Please note the groove should face downwards. ROOF TOP EDGE RIDGES FACING UP Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 16 FIXW ITH3 .0*10MMR IVET FIXW ITH3 .0*10MMR IVET FIX WITH 3.0MM RIVETS DO NOT FIX RIVETS HERE, DO NOT FIX RIVETS HERE, LEAVE FOR PAD BOLT. LEAVE FOR PAD BOLT. Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 17 Once channels are fitted to both doors, align 2 x part U4 (brace) and part W (joining brace) with holes on the back of the door and position temporarily with some tape or simply hold in place. RIDGES FACING DOWN BACK Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 18 ROOF TOP EDGE FRONT FIX WITH 3.0MM RIVETS FIXW ITH3 .0*10MMR IVET WHITEP LASTIC STOPPER WHITE PLASTIC STOPPER BACK RIDGES FACING DOWN WHITE PLASTIC WHITEP LASTIC STOPPER STOPPER Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 19 Fix the pad bolt (but NOT its keeper at this stage) using the pre-drilled holes with the self-tapping screws or the rivets provided (see diagram A and B below). BACK RIDGES FACING DOWN ROOF TOP EDGE FIX DOOR HINGES 4.0 X 10MM RIVETS FIX PAD BOLT WITH 3.0 X 10MM RIVETS Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 20 FIX PAD BOLT KEEPER FIX PADBOLT KEEPER WITH 16MM SCREWS WITH 16mm SCREWS FIX PAD BOLT KEEPER FIX PADBOLT KEEPER WITH 3.0 X 10MM RIVETS WITH 3.0*10MM RIVET Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 21 Slide the side of the roof panel with channels 26E and 26F into the ridge beam. Slide the side of the roof panel with channels 26E and 26F into the ridge beam. Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 22 THEN REPEATT HISP ROCEDUREF OR wall roof brace. THE REARW ALLR OOFB RACE PARTS 26E AND 26F (CHANNELS) ON THIS END PARTS 26A AND 26B (CHANNELS) ON THIS END Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 23 Attach part 95 (logo cap) and fix the roof panels using 16mm self-tapping screws as per diagram below. FIX WITH 16MM FIXI TW ITH1 6mmS ELF SELF-TAPPING SCREWS TAPPINGS CREWS FIX WITH 16MM FIXI TW ITH1 6mmS ELF SELF-TAPPING SCREWS TAPPINGS CREWS Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 24 Now fit the bolt down kit as per the diagram below. Strengthen your mid wall brace by applying part 72 (mid wall brace bracket) to each corner if necessary. BOLT &N UT WALL SHEET BOLT & NUT WALL SHEET STEEL ANGLE SLAB SLEEVE ANCHOR BOLT SLEEVE ANCHOR BOLT DOOR DOOR Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 25 Apply channel safety cover L type to channel 33L and R type to channel 33R for safety. Also, apply the self-tapper covers to visible in walls on the inside of the shed. screw ends visible in walls on the inside of the shed. Original Language Version GSS2323/G | Issue:2(SP) 13/04/17 © Jack Sealey Limited...
- Page 26 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.