Philips CE120/55 Quick Start Manual
Philips car entertainment system ce120 sd/sdhc card slots usb direct mp3 link
Hide thumbs
Also See for CE120/55:
- User manual (30 pages) ,
- Service manual (25 pages) ,
- Installation & connection manual (2 pages)
Advertisement
Quick Links
Download this manual
See also:
User Manual
Register your product and get support at
ENG
Quick Start Guide
N.V.
Electronics
Philips
CE120
1
a
b
c
e
g
English
reserved.
rights
All
1
Black
Koninklijke
2008
©
Overview of parts
These are the supplied parts needed to connect
2
Blue
and install this unit.
a Carry case with front panel stored inside
b Trim plate
c Standard connector
d Disassembly tool x 2 pcs
e Rubber cushion
3
Yellow
f Screw x 4 pcs
4
Pink
g Mounting bolt
5
Red
Connect wires: ISO connectors
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied
standard connector to the unit.
3
Do the other connections, if applicable.
6
Green/
black
1
Antenna
To antenna
strip
7
White/
2
Rear line out
To amplifi er line in (right)
black
(right)
strip
3
Rear line out
To amplifi er line in (left)
8
Gray/
(left)
black
strip
Connect wires: without ISO
connectors
9
Purple/
black
1
Cut off the bigger end of the supplied
strip
standard connector.
3
2
Check the car's wiring carefully and connect
Connect the supplied standard connector to
them to the supplied standard connector.
the unit.
4
Do the other connections, if applicable.
2a
d
2b
f
To a metal surface of the car
1
Antenna
To antenna
First connect the black ground
2
Rear line out
To amplifi er line
(earth) lead, then connect the
(right)
in (right)
yellow and red power supply
leads.
3
Rear line out
To amplifi er line
To the electric antenna control
(left)
in (left)
lead or power supply lead of the
antenna booster
If there is no electric antenna or
antenna booster, or it is manually
Attach the front panel
operated telescopic antenna, it
is not necessary to connect this
1
Attach the trim plate.
lead.
2
Insert the left side of the panel in the chassis
To the +12V car battery which
until it is correctly engaged.
is energized at all times .
3
Press the right side of the panel until it is
To telephone mute terminal (if
locked into place.
any) .
To the +12V power terminal
which is energized in the ac-
Mount into the dashboard
cessory (ACC) position of the
ignition switch
If there is no accessory position,
Note
connect to the +12V car battery
•
Check wire connection before you mount the
terminal that is always live. Be
unit into a car.
sure to connect the black ground
•
If preset radio stations are lost when the
(earth) lead to a metal surface of
ignition key is turned OFF and then back ON,
the car fi rst.
reconnect the red leads crosswise to the
Left speaker (Rear)
yellow ones.
1
Ensure that car dashboard opening is within
Left speaker (Front)
these measurements:
•
If the car dashboard is bigger, the sup-
plied mounting sleeve is not suitable for
Right speaker (Front)
the car. Remove the mounting sleeve
with the removal keys and consult a
professional for advice.
2
If the car does not have an on-board drive
Right speaker (Rear)
or navigation computer, disconnect the nega-
tive terminal of the car attery.
•
If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer may
lost its memory.
•
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
9
1
2
3
8
4
5
7
6
3
2
Connect the supplied mounting bolt to the
Press DBB or SEARCH to select band:
unit.
[FM1] , [FM2] , [FM3] , [AM1] , or [AM 2] .
4
3
Place the supplied rubber cushion over the
Press LOC/DX to select tuner sensitivity:
end of the mounting bolt.
[LOCAL] (local): Only station with strong
5
signal can be broadcast.
Slide the unit into the dashboard until you
hear a click sound.=
[DX] (distance): Stations with strong and
weak signals can be broadcast.
6
Reconnect the negative terminal of the car
4
battery.
Press
or
to tune to a radio station
manually.
The radio station is broadcast.
»
Detach the front panel
•
To search for radio station automatically,
press
or
for 3 seconds.
You can detach the front panel to deter theft.
Insert USB device
1
Press
to release the panel.
2
Pull the panel towards you to detach it from
1
Open the cover marked
the chassis.
panel.
3
Store the panel in the supplied carry case to
2
Insert the USB device into the USB socket.
protect it from dirt or damage.
The unit star ts playing from the USB
»
device automatically.
Turn on
1
Insert SD/MMC card
Press
to turn on the unit.
•
To turn off the unit, press
for 3
1
seconds.
Open the cover marked
panel.
Set clock
2
Insert the SD or MMC card into the card
slot.
1
Press MENU / DISP for 3 seconds.
The unit starts playing from the SD/MMC
»
2
Press DBB or SEARCH repeatedly until
card automatically.
the currently clock is displayed.
3
Turn
in clockwise direction to set hour.
Control play
Turn in anti-clockwise direction to set
minute.
4
•
To select a folder, press DBB or SEARCH
Press
to confi rm.
.
•
To skip to a track, press
View clock
•
To search within a track, press
3 seconds.
1
•
To pause, press 1 ,
. To resume, press 1 ,
Press MENU / DISP repeatedly until the clock
again.
is displayed.
Tune to a radio station
1
Press SOURCE to select Tuner.
3
2
1
on the front
on the front
or
.
or
for
Advertisement
Related Manuals for Philips CE120/55
Summary of Contents for Philips CE120/55
- Page 1 Register your product and get support at CE120 Quick Start Guide English reserved. rights N.V. Electronics Philips Koninklijke 2008 © Overview of parts These are the supplied parts needed to connect and install this unit. a Carry case with front panel stored inside...
- Page 2 English Black To a metal surface of the car First connect the black ground (earth) lead, then connect the Overview of parts yellow and red power supply leads. These are the supplied parts needed to connect Blue To the electric antenna control and install this unit.